• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2006년도 제27회 추계학술대회논문집
• /
• pp.139-145
• /
• 2006

액체추진제로켓엔진(LRE)은 로켓의 궤도 및 동특성 제어에 있어서 가장 중용한 부분 중 하나이다. LRE 제어 목적은 주어진 추력 궤도에 맞추어 추력을 조절하는 것과 주연소실과 가스발생기 내의 연소가스의 온도가 일정 범위를 넘어가지 않도록 추진제의 혼합비를 일정하게 유지시키는 것이다. 이런 제어 목적을 가진 LRE는 LRE를 구성하고 있는 구성품 간의 상호간섭에 의하여 다중제어가 쉽게 이루어지지 않는다. 본 연구에서는 LRE에 대한 동특성 모델을 구성하였으며 PID 제어와 PID+Q-ILC 제어로직을 적용한 결과에 대해 해석하였다. 전산모사 결과, PID 제어 보다 PID+Q-ILC 제어 방식을 적용할 경우 오차를 더욱 더 줄일 수 있는 것을 확인하였다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.427-428
• /
• 2002

Clearance movements of engine piston are regarded very important because they cause impact vibrations as well as many tribological problems. Some of the major parameters that influence these kinds of performances are piston profiles, piston offsets and clearance magnitudes. In our study. computational investigation is performed about the piston movements in the clearance between piston and cylinder liner by changing the skirt profiles and piston offsets. Our results show that curved profile and more offset to thrust side have better performance with low side impact during the engine cycle.

• 한국군사과학기술학회지
• /
• 제18권6호
• /
• pp.816-821
• /
• 2015

In this paper, an in-flight prediction method of thrust profiles for solid rocket motors is proposed. Actually, it is very difficult to have detailed information about the performance of the rocket motors beforehand because it is quite sensitive to combustion environments. To overcome this problem, we have developed an algorithm for generating in-flight prediction of rocket motor performance in realistic environments via a reference burnback profile and accelerations measured at a short time-interval just after launch. The performance is evaluated through a lot of flight test results.

• 한국항공운항학회지
• /
• 제14권2호
• /
• pp.39-44
• /
• 2006

The unsteady vortex lattice method is used to model lead-lag in flapping motions of a rectangular flat plate wing. The results for plunging and pitching motions were compared with the limited experimental results available and other numerical methods. They show that the method is capable of simulating many of the features of complex flapping flight. The lift, thrust and propulsive efficiency of a rectangular flat plate wing have been calculated for various lead-lag motion and reduced frequency with an amplitude of flapping angle(20o). To describe a motion profile of wing tip such as elliptic, line and circle, the phase difference of flapping and lead-lag motion was changed. And the effects of the motion profile on the aerodynamic characteristics of the flapping wing are discussed by examination of their trends.

• 한국항공우주학회지
• /
• 제48권11호
• /
• pp.837-847
• /
• 2020

본 논문에서는 20g급 날갯짓 초소형 비행체의 정지 비행 시의 날갯짓 효율을 증가시키기 위한 날갯짓 속도 분포 최적화를 진행하였다. 비원형 기어를 이용하여 다양한 날갯짓 속도 분포를 나타내는 메커니즘을 설계하였으며, 실증 기체를 이용하여 실험적으로 날갯짓 속도 분포 최적화를 진행하였다. 최적화 모델은 노이즈를 포함한 Kriging을 사용하였으며 불확실성에 의한 오차를 반영하였다. 날갯짓 속도 분포를 네 개의 파라미터로 나타내어 각 파라미터에 대한 최적화를 진행하였고. 최적화 결과 추력-파워비가 11.3% 증가하였다. 추력-파워비가 증가한 이유에 대해 탄성력에 의해 이전 스트로크에서의 각운동에너지가 일부 보존되어 다음 스트로크에서 사용되어 효율이 높아진 것으로 분석하였다.

• 설비공학논문집
• /
• 제20권2호
• /
• pp.113-120
• /
• 2008

Potential application of the scroll type machine to air compressor for fuel cell has been studied. Among the seven configuration factors which determine scroll wrap profile, the wrap thickness and the orbiting radius were chosen as two independent variables to generate various scroll wrap profiles. A conceptual design practice was conducted for scroll air compressor for SOFC with power output of 2 kW. With larger wrap thickness and orbiting radius, base plate area of the orbiting scroll becomes smaller, so is the axial gas force acting on the base plate, resulting in reduced thrust loss in spite of larger friction velocity. Performance analysis on the designed model showed that its total efficiency was 64.4% with the mass flow rate per unit compressor input of 0.00905 kg/(s kW) for the wrap thickness of 3.5 mm and the orbiting radius of 3.0 mm.

• 동력기계공학회지
• /
• 제3권1호
• /
• pp.16-22
• /
• 1999

The purpose of this study is to prevent the stick, scuffing, scratch between piston and cylinder, is to contribute the piston design such as piston profile, clearance by calculating reaction force by over-lap of piston skirt, as measuring the temperature distributions of cylinder wall. The experiment has been peformed to obtain data during actual engine operation. Temperature gradient in peripheral and axial distributions of cylinder wall according to torque and speed of engine were measured by use of an 800cc class gasoline engine. The results obtained are summarized as follows ; 1) The temperature of cylinder wall at TDC was about $50{\sim}75^{\circ}C$ higher than temperature of cooling water. 2) The rear side temperature of top dead center was $141^{\circ}C$(1/4 load) in axial distribution, whereas the rear side of midway position temperature was $98^{\circ}C$. 3) The temperature of cylinder wall increased in according to rising temperature of cooling water. 4) The thrust side temperature of cylinder wall was about $15^{\circ}C$ in all load test. 5) The rear side temperature of top dead center was $159^{\circ}C$ (1/2 load) in peripheral distribution, it was about $39^{\circ}C$ higher than thrust side temperature.

• 한국기계가공학회지
• /
• 제21권8호
• /
• pp.53-59
• /
• 2022

In this study, an experimental device was fabricated to evaluate the hovering flight performance of a single rotor on a hexacopter used for river surveillance, and a thrust performance test was conducted. In addition, the 3D profile of the propeller was extracted by 3D scanning and CFD analysis was performed using ANSYS CFD 14.5 based on the extracted 3D model of the propeller. The aerodynamic characteristics were compared with the results of the performance tests and CFD analysis, and the vortex structure corresponding to each motor rotational speed in revolutions per minute (rpm) was identified. In the future, we plan to provide valuable data for multicopter propeller design and performance verification.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2004년도 춘계학술발표회
• /
• pp.425-432
• /
• 2004

In this paper, the results of the numerical analysis for the minimum depth of soil cover have been compared with those of currently suggested codes. Based on this comparison, the minimum depth of soil cover for the structures with long spans was suggested. Results showed that the actual depth of the soil cover required against soil failure over a circular and low-profile arch structure does not vary significantly with the size of the span and for the circular structure, the minimum depth of the soil cover was about 1.5m, and for the low-profile arch structures, below about 1.6m. And the previously established code in which the minimum depth of soil cover is defined to linearly increase with the increase in the span (CHBDC, 2001) was very conservative. For the structure with the relieving slab, the maximum live load thrust was reduced by about 36 percent and the maximum moment about 81 percent. The numerical analysis gave more conservative estimation of the live-load thrusts than the other design methods.

• Tribology and Lubricants
• /
• 제31권4호
• /
• pp.177-182
• /
• 2015

Tapered roller bearings are widely used in equipment where high combined thrust and radial loads are experienced. A certain amount of tilting between the tapered rollers and the races always occurs because of bending moment load conditions and shaft deflection. It is now well understood that a coherent elastohydrodynamic lubrication (EHL) film separates the rollers and races. In spite of extensive study on EHL problems for over half a century, relatively few studies have focused on the finite line contacts problem. This study presents a complete numerical analysis of the effects of roller tilting on the EHL characteristics in a tapered roller bearing. We systematically analyze this highly nonlinear problem using finite differences with fully non-uniform grids and the Newton-Raphson method. Detailed EHL pressure distributions and film shapes are presented under moderate loads and material parameters. A very small roller tilting significantly affects the pressure distributions and film shapes near both ends of the roller. Moreover, the effect of tilting on the EHL characteristics at the small end is much greater than that at the large end. Therefore, in designing optimum profiles for tapered roller bearings, the profile radius should be larger at the small end.