• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.1
• /
• pp.1-10
• /
• 2010

Design and performance evaluation of $H_2O_2$ monopropellant thrusters to be used at reaction control of space launch vehicles were presented in this paper. Design thrust level was determined as 100, 250 Newton which is nominal thrust level for commercial space launch vehicles. Qualification thruster models including solenoid valves were developed after the reactor design were evaluated at engineering thruster models. Each thruster was evaluated by measurement of characteristic velocity, thrust, specific impulse, and pulse response times at sea level test condition.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.5
• /
• pp.325-332
• /
• 2022

The vertical take-off and vertical landing (VTVL) function is essential to carry out exploration missions on the moon or Mars. For this, the engine of the exploration vehicle must have appropriate thrust control accuracy and response time. The hybrid rocket engine (HRE) is known to have a high level of thrust control capability that can satisfy these conditions. This study aims to first verify whether the thrust control performance of the developed HRE is suitable for VTVL. To this end, an oxidizer supply system that does not use a pressurization device was adopted, aiming for a mission time of about 10 seconds. In this study, the thrust control characteristics appearing under various supply pressure decreasing conditions were identified through experiments. Appropriate tank and charging conditions were set from the experimental results. In addition, the results of previous studies and current study's test were compared to confirm whether the developed HRE had adequate control performance for VTVL, and finally, the thrust control performance was verified through altitude control simulation.

• Journal of Institute of Control, Robotics and Systems
• /
• v.6 no.11
• /
• pp.981-986
• /
• 2000

A pulse amplitude modulation(PAM) controller is designed for the 3 axis attitude control of a sounding rocket. a certain number of fixed level of thrust are used for the pulse amplitude modulation and the nonlinearity of the controller is considered to examine the existence of the limit cycles and the stability analysis is carried out with the aid of Nyquist plot.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.22 no.4
• /
• pp.93-98
• /
• 2014

In this study, control of oxidizer mass flow rate and verification of control system were performed for hybrid rocket thrust control application. Oxidizer flow control system consists of ball valve and stepping motor where gaseous oxygen was used for oxidizer at feeding pressure of 10, 20 and 30 bar. According to experimental results, the oxidizer mass flow rate showed a relatively linear increment as ball valve open angle increases regardless of feeding pressure. In addition, the level of the oxidizer flow rate was kept almost constant at each sequence of flow control with ball valve during the 20 seconds of operation.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.237-240
• /
• 2007

To control Thrust of propulsion system, we built the 50 N level PE-COx hybrid rocket, and changed the mass flow rate of COx. From the preliminary experiential results, we could see possibility of controlling thrust of the hybrid rocket by controlling mass flow rate of COx.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.257-260
• /
• 2008

In order to control thrust of propulsion system, we built the 50 Newton level PE-GOx hybrid rocket, and changed the mass flow rate of GOx. From the preliminary experiential results, we could see possibility of controlling thrust of hybrid rockets by controlling mass flow rate of GOx.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.1
• /
• pp.40-47
• /
• 2010

In this study, basic research on the thrust control by controling oxidizer mass flow rate of a $GO_2$/PE hybrid rocket is presented. For this purpose, hybrid rocket system including oxidizer flow control system and data acquisition system was developed. To control oxidizer mass flow rate, we used needle valve with stepping motor which was controled by LabVIEW program. During the fundamental experiments, this system managed to follow the pre-programmed (20 N - 10 N - 20 N - 0 N) thrust level.

• Aerospace Engineering and Technology
• /
• v.12 no.1
• /
• pp.189-199
• /
• 2013

This paper summarizes results of second stage attitude control of KSLV-I third flight test. The results show that three axes attitude control at coasting phases of KSLV-I was successfully accomplished by the reaction control system, and pitch and yaw attitude control at thrusting phase where second stage kick motor burns was also normally accomplished by using the thrust vector control system. It is verified that the second stage controller performed successfully for all flight phases regardless of some disturbances due to mass center offset, slag effects, and residual thrust of kick motor. These results may provide an important basis in enhancing domestic technology level of attitude control of launch vehicle.

• 한국전산유체공학회:학술대회논문집
• /
• 2001.05a
• /
• pp.21-29
• /
• 2001

For rapid and abrupt control of a missile in supersonic flight, side jet on a missile body is found to be a useful devise as evidenced by recent missile development at several nations. The magnitude of the side jet and the duration of it decide the level of control of such a missile system. In this paper, the aerodynamic characteristics of the side jet devise itself are examined in terms of key parameters such as the side jet nozzle contour, the chamber pressure and temperature. Specifically attention is focused on the effect of the chamber shape between the straight nozzle and the bended nozzle by 90 degrees. The flow properties as well as the thrust level are compared between the two shapes. Particular attention is paid at the way the nozzle is bended at the joint. Effects of the length and the divergence angle of the nozzle on the thrust magnitude are also quantified among the three different side jet nozzles.

• Tribology and Lubricants
• /
• v.36 no.1
• /
• pp.27-33
• /
• 2020

Self-equalizing tilting pad thrust bearings are usually employed in turbomachines to achieve high stability and reliability. A tilting pad bearing can incorporate self-equalizing links to handle the misalignment between the bearing and the thrust collar. In this popular design method, the pads sit on the upper-level plates and the lower-level plates stay on the retainer base. With misalignment, the pads that are heavily loaded are pushed down. Consequently, the link pushes up the pads on the opposite side, keeping the bearing surface parallel to the thrust collar surface. The self-equalizing link is used to handle the misalignment from the thermal and mechanical effects. In this study, the experimental investigation deals with the performance of self-equalizing tilting pad thrust bearings. The test rig for evaluating the performance of bearing is developed which can control the misalignment angle. Simultaneous measurements are taken for the force acting on each pad. Pad metal temperature and oil film thickness are functions of the shaft speed, bearing load, misalignment angle, and design of leveling plates. The effect of misalignment on bearing performance is discussed. The results demonstrate that the load on each pad depends on the test conditions(especially misalignment angle), and the load influences the performance of bearings.