• Journal of Biosystems Engineering
• /
• 제27권2호
• /
• pp.89-96
• /
• 2002

The trend of consumption of vegetable soybeans is increasing because they are recognized as the clean vegetable. The works requiring the most intensive labor are threshing and seperation ones, and they form about 80% of total labour for vegetable soybeans production. It is necessary to develop the vegetable soybeans-thresher for the sake of cost down of vegetable soybeans production. The purpose of this study is to acquire the basic informations to design of the vegetable soybeans-thresher. We make the experimental system which control the speed of threshing cylinder and the teeth gap and investigate the detachment forces. The result are as follows ; The ratio of un-threshed soybeans-pod to stem after threshing work is decreasing as the threshing cylinder speed increases: 0.0% and 2.8% at 55m/s and 18m/s of threshing cylinder speed respectively. Also the ratio of un-threshed soybeans-pod to stem is shown as 2.0% below in the condition of 64~160mm of teeth gap and over 28m/s of threshing cylinder speed. The damaged pod ratio of detached soybeans after threshing work is decreasing as the threshing cylinder speed increases: 4.8% and 1.3% at 55m/s and 18m/s of threshing cylinder speed respectively. The minimum damaged pod ratio of detached soybeans are shown as 1.0%, 1.5% and 1.9% at 18m/s, 28m/s and 37m/s of threshing cylinder speed respectively. The average detachment forces of pods are shown as 1.5kg$_{f}$ for 3 grains, 1.2kg$_{f}$ for 2 grains and 0.8kg$_{f}$ for 1 grain respectively. The maximum detachment force of pod is shown as 2.7kg$_{f}$ for 3 grains. grains.

• Journal of Biosystems Engineering
• /
• 제7권1호
• /
• pp.33-41
• /
• 1982

When wet-paddy is threshed by conventional auto-fed thresher, the threshed material under the concave is difficult to separate with pneumatic separation only. The development of thresher with an oscillating sieve in addition to the conventional pneumatic separation has been recommanded to improve the separation of grains from straw and chaff having high moisture content. This study was intended to evaluate the separating performance of an oscillating sieve and to obtain the effective operation conditions of the sieve separation. The sieve with oscillating in an elliptical motion was developed and installed in the experimental unit which can simulate the separating operation of the conventional auto-fed thresher. Results of the study are summarized as follows: 1. The flowing velocity of grains on oscillating sieve was increased as the sieve frequency increased but the feed rate did not significantly affect the flowing velocity of grains on sieve. 2. The effects of sieve frequency and the direction of sieve rotation on the separating performance by oscillating sieve show that increasing the frequency of sieve driving crank above the 460 rpm in the same direction of material flow (con-flow) improved the separating performance. 3. The height of grain guide plate and air velocity through the sieve to optimize the separating performance of oscillating sieve were experimentally determined to give about 10cm above the sieve and 7 m/s, respectively.

• Journal of Biosystems Engineering
• /
• 제15권2호
• /
• pp.110-122
• /
• 1990

This study was undertaken to develop the feed rate control system for the head feed thresher by making use of the microprocessor and to evaluate the response of the system to a various threshing conditions. The control unit was composed of one-board microcomputer. The speed of the wet-paddy feeding chain was controlled by dc moter with PI controller. It was used the adaptive control method to maintain the constant feed rate regardless of the fed rice varieties. The sliding type potentiometer was used as the feed rate sensor, which was attached on the sheaf-holding apparatus. The mathematical models of the system components were derived and computer simulation was developed for investigating the parameters affecting on control performance and for estimating the response of the system. A one-board microcomputer-based feed rate control system developed in this study was properly functioned and assessed as adequate for the feed rate control system of the head feed thresher. Based on the simulation for the bundle feed, it was anticipated that the lower setting value of the cylinder speed(RL) is to be set higher than the limiting operational speed. In addition, the higher setting value of the cylinder speed(RH) is to be set lower than the limiting cylinder speed for threshing. The computer simulation for the continuous spread feed showed that the lower the setting value of straw layer thickness(LL) was set, the shorter the correction time. However, if too low LL may be established, the feed rate could not reach to its desired rate.

• Journal of Biosystems Engineering
• /
• 제32권5호
• /
• pp.324-331
• /
• 2007

The purpose of this study is to analysis effects of defect factors of combine header for cutting speed of combine header, feeding depth of straw, and cylinder speed of thresher. Measurement system for defect factors was consists of sensors to monitor the combine operation and I/O interface to convert the signals. Cutting speed of combine header, feeding depth of straw, cylinder speed of thresher were measured and analyzed. The data were collected from three paddy field during rice harvesting. The tests were conducted at different grounding speeds, lug troubles, and cutter condition. The one way ANOVA and the multiple comparison tests were performed. The results showed that the measured data were useful to monitor the defect factors of combine during harvesting. The faults conditions of grounding speeds, lug troubles, and cutter conditions affected cutting speeds, feeding depths and cylinder speeds of the combine. The data seem to be useful to analysis the faults conditions of combine header.

• Journal of Biosystems Engineering
• /
• 제6권1호
• /
• pp.48-59
• /
• 1981

The major limiting factor on the determination of combine capacity is the frequent occurence of clogging over the some parts of machine when the crop is wet in the case of Japanese self-feeding type combine. And in the case of American conventional combine having big separating parts, the great grain loss and damage occur when the machine is used for rice harvesting. This experiment was carried out to develop the new type threshing and separating equipment. Proto-type thresher which consist of a conical threshing drum and a conical separating sieve rotating around the threshing cone was constructed and tested. In the case of 800 rpm of threshing cone speed, average threshing loss was below 1 percent, separating loss was about 1 percent, grain damage was about 0.4 percent, and average total power required was about 2.6 PS. This design has some problems such as higher power required or wrapping problems under the conditions of feeding long damp straw. But, compared with the conventional combine or thresher, this machine certainly has some potentials for this approach to combine development. The crop feed rate must be increased through improvement of the feeding portion of the threshing cone. And it is required to investigate further about some parameters causing wrapping phenomena.

• Journal of Biosystems Engineering
• /
• 제18권4호
• /
• pp.371-381
• /
• 1993

Threshing operation is performed by impact, compression and friction forces inside the thresher. These values should be appropriate to the crop condition to enhance the threshing and separating efficiency and to decrease the grain damage. To analyze the threshing process inside the rasp-bar type thresher, impact, friction and compression forces were measured using transducers with strain gage circuits. To measure the impact forces and friction forces between the rasp-bar and crop, full bridge strain gage circuit was built on the rasp-bar holder. To measure the compression forces and circumferential friction forces between the concave and crop, two sets of full bridge strain gage circuits were built on the T-type concave transducer. Threshing work of wheat crop with 12% of moisture content was performed at 3 levels of compression ratio and with 3 replications. Each transducer could not measure the exact forces continuously because the transducer oscillates with the forces. However they could measure maximum forces and force distribution according to the time. Average friction coefficients between crop and concave was 0.61 not showing any significant difference according to the compression ratio. Average acceleration of the crop in the cylinder appeared from $70.6m/s^2$ to $140.8m/s^2$ according to the compression ratio. The velocity of the crop at the exit of the cylinder appeared from 10.7m/s to 15.0m/s according to the compression ratio.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2003년도 하계 학술대회 논문집
• /
• pp.309-316
• /
• 2003

참깨탈곡의 생력기계화를 위해 일관작업이 가능한 참깨탈곡기를 개발하여 시험한 결과를 요약하면 다음과 같다. 가. 타격식 탈곡요인시험 결과 타격수 14, 17cpm에서 탈곡률은 98.5, 98.7%, 미탈곡률은 1.1, 1.0%, 배출구 손실률은 0.4. 0.3%로 가장 양호하게 나타났다. 나. 타격식 탈곡물의 정선요인시험결과 경사 12$^{\circ}$, 요동수 220cpm일 때 탈곡률과 미정선 손실률이 각각 97.2%와 0.6%로 가장 양호하게 나타났다. 다. 타격식 탈곡부와 정선부를 조합한 시작기의 성능시험결과 공급량 15단/min, 타격수 14cpm, 정선체 요동수 220cpm에서 탈곡률은 98.7%, 탈곡부 손실률은 1.3%, 정선율은 97.0%, 미정선 손실률 0.7%로 나타났다. 라. 시작기는 10a당 작업성능이 0.5시간으로 인력 4.8시간에 비해 9.6배 능률적이고 소요경비가 17,471원으로 인력 32,290원에 비해 45.9% 절감되는 것으로 나타났다

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2001년도 동계 학술대회 논문집
• /
• pp.199-204
• /
• 2001

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2001년도 동계 학술대회 논문집
• /
• pp.90-95
• /
• 2001

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1997년도 하계 학술대회 논문집
• /
• pp.3-9
• /
• 1997