• 한국전산유체공학회지
• /
• 제4권3호
• /
• pp.52-62
• /
• 1999

The development of a parallelized aerodynamic simulation process involving moving bodies is presented. The implementation of this process is demonstrated using a fully systemized Chimera methodology for steady and unsteady problems. This methodology consists of a Chimera hole-cutting, a new cut-paste algorithm for optimal mesh interface generation and a two-step search method for donor cell identification. It is fully automated and requires minimal user input. All procedures of the Chimera technique are parallelized on the Cray T3E using the MPI library. Two and three-dimensional examples are chosen to demonstrate the effectiveness and parallel performance of this procedure.

• 한국자동차공학회논문집
• /
• 제5권4호
• /
• pp.207-218
• /
• 1997

A new blank design method is introduced to predict the blank shape and the strain distribution in the sheet metal forming process. This method deals with only one step from the final shape to the initial blank using the ideal forming theory. Based on this theory, a three-dimensional membrane finite element code has been developed to design an initial blank in the sheet metal forming process. In this paper, the designs of initial blanks for forming a cylindrical cup, a rectangular cup, and a front fender are presented as examples. Also, it compares the two shapes, the target shape with the shape which is deformed from the initial blank using the FEM analysis code. The results illustrate the information that this direct design code is useful in the preliminary design state.

• Journal of Mechanical Science and Technology
• /
• 제19권2호
• /
• pp.649-654
• /
• 2005

This paper presents fabrication and drive test of a peristaltic PDMS micropump actuated by the thermopneumatic force. The micropump consists of the three peristaltic-type actuator chambers with microheaters on the glass substrate and a microchannel connecting the chambers and the inlet/outlet port. The micropump is fabricated by the spin-coating process, the two-step curing process, the JSR (negative PR) molding process, and etc. The diameter and the thickness of the actuator diaphragm are 2.5 mm and $30{\mu}m$, respectively. The meniscus motion in the capillary tube is observed with a video camera and the flow rate of the micro pump is calculated through the frame analysis of the recorded video data. The maximum flow rate of the micropump is about $0.36\;{\mu}L/sec$ at 2 Hz for the zero hydraulic pressure difference when the 3-phase input voltage is 20 V.

• 한국분말재료학회지
• /
• 제9권4호
• /
• pp.203-210
• /
• 2002

A new PIM in-process joining technique has been developed for more complicated and functional PIM components by application of the exuded wax from the green compacts during solvent debinding step. At first, various stainless steels and iron compacts with rectangular shape were combined, and the joining behaviors and properties were investigated by shear and tensile test, and microscopic observation. Subsequently, perfect joined three pieces of thin and hollow compacts were obtained for the combination of same and different stainless steels, and it was difficult to join the iron and stainless steel compacts in hydrogen atmosphere because of the different starting temperature of shrinkage. However, pretty good joined iron and stainless steel compacts were obtained by consideration of particle size and vacuum atmosphere. Finally, for the combination of ferro-silicon and austenitic stainless steel compacts, high functionality (magnetic (1.60Tes1a) & non-magnetic) and perfect joint were obtained.

• 한국디지털건축인테리어학회논문집
• /
• 제8권1호
• /
• pp.5-14
• /
• 2008

This study is the one of the step to propose the Design studio course that apply concept of 'BIM" that is new digital environment of Architecture. This Study propose as followed, First. The proposal of the experimental course of the Design studio, Second, Application of course of study, Third, The design course of study is proceeded by purpose of completion of BIM. This study is proceeded by the purpose of the concept of the BIM first and proposals of fundamental ideas that apply the idea. Proposed training courses are marked by that divide three areas of information - architecture information, environment information, drawing information - with process consisted in professional practice of design and adjust each process and sequence. Also, this study suggest process that applying BIM tools in this work as the basis frame.

• 센서학회지
• /
• 제24권2호
• /
• pp.83-87
• /
• 2015

In this paper, we fabricated a low-cost glucose sensor with a simpler structure and fabrication process than the existing glucose sensor. The currently used glucose sensor has a three-layer structure with upper, middle, and bottom plates; here, we fabricated a single-layer glucose sensor using only a printing and dispensing process. We successfully fabricated the glucose sensor using a simple method involving the formation of an electrode and insulator layer through a 2- or 3-step printing process on plastic or paper film, followed by the dispensing of glucose oxidase solution on the electrode. Cyclic voltammetry (CV) and cyclic amperometry (CA) measurements were used to evaluate the characteristics of the fabricated single-layer glucose sensor. Also, its sensitivity was analyzed through glucose-controlled blood measurements. Hence, a low-cost single-layer glucose sensor was fabricated with evaluation of its characteristics demonstrating that it has useful application in medicine.

• 한국정밀공학회지
• /
• 제17권1호
• /
• pp.179-184
• /
• 2000

Chemical Mechanical Polishing (CMP) refers to a material removal process done by rubbing a work piece against a polishing pad under load in the presence of chemically active and abrasive containing slurry. CMP process is a combination of chemical dissolution and mechanical action. The mechanical action of CMP involves hydrodynamic behavior. The liquid slurry is trapped between the work piece and pad forming a hydrodynamic film. For the first step to understand material removal mechanism of the CMP process, the hydrodynamic analysis is done with semiconductor wafer. Three-dimensional Reynolds equation is applied to get pressure distribution of the slurry film. Shear stress distributions on the wafer surface are also analyzed

• Earthquakes and Structures
• /
• 제16권1호
• /
• pp.29-39
• /
• 2019

A three-step screening process is presented in this article for selection of consistent earthquake records in which number of suitable ground motions is quickly screened and reduced to a handful number. Records that remain at the end of this screening process considerably reduce the dispersion of structural responses. Then, an effective method is presented for spectral matching and modification of the selected records. Dispersion of structural responses is explored using different statistical measures for each scaling procedure. It is shown that the Uniform Design Method, presented in this study for scaling of earthquake records, results in most cases in the least dispersion measure.

• 제어로봇시스템학회논문지
• /
• 제21권12호
• /
• pp.1122-1129
• /
• 2015

This paper suggests a method of detecting traffic lights for vehicles by combining the HSV(hue saturation value) color model, morphometric characteristics, and location information appearing on consecutive images in daytime. In order to detect the traffic light, the color corresponding to the signal lights should be explored. It is difficult to detect traffic lights among colors of lights from buildings, taillight of cars, leaves, placards, etc. The proposed algorithm searches for the traffic lights from many candidates using morphometric characteristics and location information in consecutive images. The recognition process is divided into three steps. The first step is to detect candidates after converting RGB channel into HSV color model. The second step is to extract the boundaries between the housing of traffic lights and background by exploiting the assumption that the housing has lower brightness than the surrounding background. The last step is to recognize the signal light after eliminating the false candidates using morphometric characteristics and location information appearing on consecutive images. This paper demonstrates successful detection results of traffic lights from various images captured on the city roads.

• 복식문화연구
• /
• 제28권4호
• /
• pp.508-526
• /
• 2020

This study has established a fashion illustration education plan using the contour drawing that fosters observational ability and enables creative drawing. This study developed two illustration curriculum proposals consisting of 15 weeks, combining literature and case studies. The researchers organized a step-by-step teaching plan that utilizes contour drawing according to the three stages of fashion illustration classes: foundation courses, general courses, and intensive courses. When the contour drawing is used at the beginning stage of the foundation courses of fashion illustration, it can be used as a technique to reduce the fear of students about practical skills, induce interest in illustration, and cultivate observation ability about objects. In general process, it is combined with various tools and coloring materials to strengthen expression power, and it is possible to produce detailed expressions and illustrations about human body and clothing. In intensive courses, it is expanded to the production of creative works with new aesthetics through digital techniques and mixed materials. As such, the contour drawing is expanded in various ways according to the learning contents and goals of each step, and is flexibly adjusted according to the learning content. Contour drawing has the effect of acquiring observation and expression ability, and it is analyzed as a technique that enables the production of creative illustration of students.