• Transactions of the Korean hydrogen and new energy society
• /
• v.31 no.1
• /
• pp.33-40
• /
• 2020

As hydrogen utilization becomes more active recently, a large amount of hydrogen should be supplied safely. Among the three supply methods, liquefied hydrogen, which is an optimal method of storage and transportation convenience and high safety, has a low temperature of -253℃, which is complicated by the liquefaction process and consumes a lot of electricity, resulting in high operating costs. In order to reduce the electrical energy required for liquefaction and to raise the efficiency, hydrogen is cooled by using a mixed refrigerant in a precooling step. The electricity required for the precooling process of the mixed refrigerant can be reduced by using the cold energy of LNG. Actually, LNG cold energy is used in refrigeration warehouse and air liquefaction separation process, and a lot of power reduction is achieved. The purpose of this study is to replace the electric power by using LNG cold energy instead of the electric air-cooler to lower the temperature of the hydrogen and refrigerant that are increased due to the compression in the hydrogen liquefaction process. The required energy was obtained by simulating mixed refrigerant (MR) hydrogen liquefaction system with LNG cold heat and electric system. In addition, the power replacement rate of the electric process were obtained with the pressure, the temperature of LNG, the rate of latent heat utilization, and the hydrogen liquefaction capacity, Therefore, optimization of the hydrogen liquefaction system using LNG cold energy was carried out.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.386-391
• /
• 2001

A finite element code based on P2P1 tetra element has been developed for the large eddy simulation (LES) of turbulent flows around a complex geometry. Fractional 4-step algorithm is employed to obtain time accurate solution since it is less expensive than the integrated formulation, in which the velocity and pressure fields are solved at the same time. Crank-Nicolson method is used for second order temporal discretization and Galerkin method is adopted for spatial discretization. For very high Reynolds number flows, which would require a formidable number of nodes to resolve the flow field, SUPG (Streamline Upwind Petrov-Galerkin) method is applied to the quadratic interpolation function for velocity variables, Noting that the calculation of intrinsic time scale is very complicated when using SUPG for quadratic tetra element of velocity variables, the present study uses a unique intrinsic time scale proposed by Codina et al. since it makes the present three-dimensional unstructured code much simpler in terms of implementing SUPG. In order to see the effect of numerical diffusion caused by using an upwind scheme (SUPG), those obtained from P2P1 Galerkin method and P2P1 Petrov-Galerkin approach are compared for the flow around a sphere at some Reynolds number. Smagorinsky model is adopted as subgrid scale models in the context of P2P1 finite element method. As a benchmark problem for code validation, turbulent flows around a sphere and a MIRA model have been studied at various Reynolds numbers.

• Journal of the Korean Ceramic Society
• /
• v.50 no.2
• /
• pp.122-126
• /
• 2013

The surface roughness of the inner and outer surfaces of a tube is an important requirement for nuclear fuel cladding. When an inner SiC clad tube, which is considered as an advanced Pressurized Water Cooled Reactor (PWR) clad with a three-layered structure, is fabricated by Chemical Vapor Deposition (CVD), the surface roughness of the substrate, graphite, is an important process parameter. The surface character of the graphite substrate could directly affect the roughness of the inner surface of SiC deposits, which is in contact with a substrate. To evaluate the effects of the surface roughness changes of a substrate, SiC deposits were fabricated using different types of graphite substrates prepared by the following four polishing paths and heat-treatment for purification: (1) polishing with #220 abrasive paper (PP) without heat treatment (HT), (2) polishing with #220 PP with HT, (3) #2400 PP without HT, (4) polishing with #2400 PP with HT. The average surface roughnesses (Ra) of each deposited SiC layer are 4.273, 6.599, 3.069, and $6.401{\mu}m$, respectively. In the low pressure SiC CVD process with a graphite substrate, the removal of graphite particles on the graphite surface during the purification and the temperature increasing process for CVD seemed to affect the surface roughness of SiC deposits. For the lower surface roughness of the as-deposited interlayer of SiC on the graphite substrate, the fine controlled processing with the completed removal of rough scratches and cleaning at each polishing and heat treating step was important.

• Journal of Families and Better Life
• /
• v.24 no.5 s.83
• /
• pp.251-270
• /
• 2006

This study examined how the households used and combined financing sources to pay for college education. It compared the probability of using each source (current incomes, saving, education loans and grants) by households' socio-economic characteristics and analyzed which factors influence the decision to use each source and the amounts from each source for financing college education. Data for this study were from a questionnaire completed by 4-year college students (n=623) and were analyzed by t-tests, ANOVA and Heckman's two-step estimation models. The findings of this study were as follows: First, the most frequent source for college education was parents' savings and the second one was parents' incomes. Also, the most frequent combination of sources was saving and current incomes and the second was combination of three sources, saving, incomes and education loans. Second, the probability of using incomes was higher for younger students than for older students. The number of siblings showed significant differences among income, savings and education loans. Those who had higher incomes were more likely to use current incomes, saving, but less likely to borrow for financing college education. Middle-class income groups were more likely to borrow for education. Third, household incomes and asset holdings had generally positive impacts on the probability of using incomes and savings for college education, while total debt burden decreased both the probability and amounts of income and saving sources. The college costs had significantly positive effects on both the probability and the amounts of all of financing sources. Total grants received significantly decreased the amounts from incomes, savings and borrowing sources.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.1
• /
• pp.71-79
• /
• 2014

A parallelization of the bi-conjugate gradient solver for the pressure equation of the CUPID (component unstructured program for interfacial dynamics) code, which was developed for analyzing the components of a pressurized water-cooled reactor, was studied in a symmetric multi-processing system. The parallel performance was investigated for three typical parallel programming models (MPI, OpenMP, Hybrid) by solving incompressible backward-facing step flow at various grid resolutions. It was confirmed that parallel performance was low when problem size was small or the memory requirement for each thread was considerably higher than the cache memory. Furthermore, it was shown that MPI was better than OpenMP regardless of the problem size, and Hybrid was the best when the number of threads was relatively small.

• Structural Engineering and Mechanics
• /
• v.66 no.4
• /
• pp.505-513
• /
• 2018

Steam flooding is widely used in heavy oil reservoir with coupling effects among the formation temperature change, fluid flow and solid deformation. The effective stress, porosity and permeability in this process can be affected by the multi-physical coupling of thermal, hydraulic and mechanical processes (THM), resulting in a complex interaction of geomechanical effects and multiphase flow in the porous media. Quantification of the state of deformation and stress in the reservoir is therefore essential for the correct prediction of reservoir efficiency and productivity. This paper presents a coupled fluid flow, thermal and geomechanical model employing a program (MATLAB interface code), which was developed to couple conventional reservoir (ECLIPSE) and geomechanical (ABAQUS) simulators for coupled THM processes in multiphase reservoir modeling. In each simulation cycle, time dependent reservoir pressure and temperature fields obtained from three dimensional compositional reservoir models were transferred into finite element reservoir geomechanical models in ABAQUS as multi-phase flow in deforming reservoirs cannot be performed within ABAQUS and new porosity and permeability are obtained using volumetric strains for the next analysis step. Finally, the proposed approach is illustrated on a complex coupled problem related to steam flooding in an oil reservoir. The reservoir coupled study showed that permeability and porosity increase during the injection scenario and increasing rate around injection wells exceed those of other similar comparable cases. Also, during injection, the uplift occurred very fast just above the injection wells resulting in plastic deformation.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.801-803
• /
• 1998

We investigated Pt and $RuO_2$ as a bottom electrode and PZT thin film for ferroelectric applications. XRD examination shows that a mixed phase of (111) and (200) Pt peak for the temperature ranged from RT to $200^{\circ}C$, and a preferred (111) orientation for the substrate temperature of $300^{\circ}C$. From the XRD and AFM results, we recommend the substrate temperature of $300^{\circ}C$, 80 W for the Pt bottom electrode growth. From the study of an oxygen partial pressure from 0 to 50%, we learned that only Ru metal was grown with $0{\sim}5%$, a mixed phase of Ru and $RuO_2$ for $10{\sim}40%$, pure $RuO_2$ at 50%. Having optimized the bottom electrode growth conditions, we employed two step process in PZT film capacitor: PZT film growth at the low substrate temperature of $300^{\circ}C$ and then post RTA anneal treatments. PZT films were randomly oriented on $RuO_2$ and (110) preferentially oriented on Pt electrode. Leakage current density of PZT film demonstrated two to three orders higher for $RuO_2$ bottom electrode. From C-V results we observed a dielectric constant of PZT film higher than 1200. This paper presents the optimized process conditions of the bottom electrodes and properties of PZT thin films on these electrodes.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.355-360
• /
• 2002

ElectroSlag Strip Overlaying (ESSO) process has been around since 1970. ESSO process had limited acceptance due to a few problems associated with the use of this process in its very early stage. Limited knowledge and, most significantly, poor quality of the equipment and welding flux gave the ESSO process a bad name. However, this process is well accepted today and used in North America, Europe and Japan. The ESSO process provides low dilution overlays at high deposition rates, excellent and consistent deposit chemistry with excellent surface quality, and virtually no defects. Capitan has taken this process one step further through extensive research and development of the process itself as well as the equipment. The improvement brought to the process warranted the issuance in May 2000 of an US patent. This study demonstrates the feasibility of this process with immediate positive production results. The main achievements of this work are as follows: $\textbullet$ Development of six various strip-flux combinations on three different base materials: carbon steel, $\frac{1}{4}$ Cr/.5 Mo and 2 $\frac{1}{4}$ Cr/l Mo, fully tested with: penetrant, ultrasound, bends, hardness, overlay chemistry, corrosion and hydrogen disbonding. $\textbullet$ 12" dia. 90 hot formed elbows from straight pipe electroslag overlayed with "1 layer" and "2 layer" Alloy 625 $\textbullet$ a very unique development of miniaturized overlaying equipment able to perform overlay in pipe with diameters as low as 10" (254 mm). This development has large applications in the field of offshore, petrochemical, refining, pulp and paper and power generation industries. The aftermath of this development was its immediate acceptance by major end users with the completion of four projects of overlayed pipe in the USA and Far East Asia.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.9
• /
• pp.1149-1164
• /
• 1997

In this study, the applicability of the RNG k-.epsilon. model to the analysis of the complex flows is studied. The governing equations based on a non-orthogonal coordinate formulation with Cartesian velocity components are used and discretized by the finite volume method with non-staggered variable arrangements. The predicted results using the RNG k-.epsilon. model of three complex flows, i.e., the flow over a backward-facing step and a blunt flat plate, the flow around a 2D model car are compared to these from the standard k-.epsilon. model and experimental data. That of the unsteady axisymmetric turbulent flow within a cylinder of reciprocating model engine including port/valve assembly and the spray characteristics within a chamber of direct injection model engine are compared to these from the standard k-.epsilon. model and experimental data. The results of reattachment length, separated eddy size, average surface pressure distribution using the RNG k-.epsilon. model show more reasonable trends comparing with the experimental data than those using the modified k-.epsilon. model. Although the predicted rms velocity using the modified k-.epsilon. model is lower considerably than the experimental data in incylinder flow with poppet valve, predicted axial and radial velocity distributions at the valve exit and in-cylinder region show good agreements with the experimental data. The spray tip penetration predicted using the RNG k-.epsilon. model is more close to the experimental data than that using the modified k-.epsilon. model. The application of the RNG k-.epsilon. model seems to have some potential for the simulations of the unsteady turbulent flow within a port/valve-cylinder assembly and the spray characteristics over the modified k-.epsilon. model.

• Journal of the Korea Convergence Society
• /
• v.9 no.10
• /
• pp.109-120
• /
• 2018

The purpose of this study was to investigate the effects of functional electrical stimulation (FES) with mirror therapy on balance and gait ability in chronic stroke patients. Thirty-five subjects who met the inclusion criteria were randomly allocated into three groups: the functional electrical stimulation with mirror therapy group(FMT group, n=11), mirror therapy group(MT group, n=12), and control group (n=12). The exercises were conducted for 30 min per day, five, per week for four weeks. Balance and gait ability were examined at baseline and after 4 weeks of intervention. After training, the FMT group showed significant improvement in berg balance scale (BBS), center of pressure (COP) length, affected step length (ASL), Cadence and average gait speed (AGS) compared MT group and control group(p<0.05). This findings show that FES and MT convergence can be an effective intervention for stroke patients balance and gait ability. Continued development of convergence interventions for stroke patients with balance and gait ability in practice, are suggested.