• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.201-204
• /
• 2007

This paper proposes a improvement of switching converter's input wave form using VIENNA Rectifier(three-phase three-switch three-level PWM Rectifier). VIENNA Rectifier is based on the combination of a three-phase diode bridge and dc/dc boost converter. It can be available to get sinusoidal mains current, and low-blocking voltage stress on rower transistors. In addition, it can control output voltage.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 전력전자학술대회 논문집
• /
• pp.149-153
• /
• 1998

In this paper A switched mode AC/DC three phase boost converter with high power factor and sinusoidal input current waveform is analyzed and simulated. The proposed converter retain high power factor and sinusoidal input current waveform even under electric arc welder load. It is shown that experimental result and simulation waveform yield a sinusoidal input current waveform at high power factor.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2007년도 하계학술대회 논문집
• /
• pp.19-21
• /
• 2007

This paper proposes an input waveform improvement using VIENNA Rectifier(three-phase/level/switch). VIENNA Rectifier is based on the combination of a three-phase diode bridge and dc/dc converter. It features low input current ripple and sinusoidal mains current form.

• 전기학회논문지
• /
• 제62권6호
• /
• pp.767-781
• /
• 2013

In this paper, we proposes the AC input voltage and current sensorless control scheme to control the input power factor and DC output voltage of the three-phase Z-source PWM rectifier. For DC-link voltage control which is sensitive to the system parameters of the PWM rectifier, fuzzy-PI controller is used. Because the AC input voltage and current are estimated using only the DC-link voltage and current, AC input voltage and current sensors are not required. In addition, the unity input power factor and DC output voltage can be controlled. The phase-angle of the detected AC input voltage and estimated voltage, the response characteristics of the DC output voltage according to the DC voltage references, the FFT results of the estimated voltage and current, efficiency, and the response characteristics of the conventional PI controller and fuzzy-PI controller are verified by PSIM simulation.

• Journal of Power Electronics
• /
• 제19권1호
• /
• pp.89-98
• /
• 2019

This paper analyzes the input side performance of a conventional three-phase to single-phase matrix converter (3-1MC). It also presents the input-side waveform quality under this topology. The suppression of low-frequency input current harmonics is studied using the 3-1MC plus capacitance compensation unit. The constraint between the modulation function of the output and compensation sides is analyzed, and the relations among the voltage utilization ratio and the output compensation capacitance, filter capacitors and other system parameters are deduced. For a 3-1MC without large-capacity energy storage, the system performance is susceptible to input voltage imbalance. This paper decouples the inner current of the 3-1MC using a Lyapunov function in the input positive and negative sequence bi-coordinate axes. Meanwhile, the outer loop adopts a voltage-weighted synthesis of the output and compensation sides as a cascade of control objects. Experiments show that this strategy suppresses the low-frequency input current harmonics caused by input voltage imbalance, and ensures that the system maintains good static and dynamic performances under input-unbalanced conditions. At the same time, the parameter selection and debugging methods are simple.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 춘계학술대회 논문집
• /
• pp.631-636
• /
• 1995

A robotic wrist with three rolling motion is considered. It has the gear trains with three independent input parameters and mechanical interference in their motion. This paper presents dervation of basic kinematic equations that relate the input parameters and the orientation of the end-effector, determination of singularities in its motion, and the computational procedure of the inverse kinematics.

• Journal of Power Electronics
• /
• 제8권1호
• /
• pp.60-73
• /
• 2008

In this paper a three-phase ac-to-dc resonant converter with high input power factor and isolated output is proposed. To improve the input power factor of the converter, high frequency current is injected into the input of the three-phase diode bridge rectifier. It is injected through an impedance network consisting of a series of L-C branches from the output of the high frequency three-phase inverter. A narrow switching frequency variation is required to regulate the output voltage. A design example with different design curves is illustrated along with the component ratings. Experimental verification of the converter is performed on a prototype of 3 kW, 1000 V output, operating above 300 kHz. Experimental results confirm the concept of the proposed converter. Narrow switching frequency variation is required to regulate the output voltage.

• 제어로봇시스템학회논문지
• /
• 제17권11호
• /
• pp.1138-1144
• /
• 2011

This article deals with the problem of fault detection of a spacecraft's actuators. The authors introduce an extended unknown input observer for nonlinear systems. This is an extended form of unknown input observers which are used for linear systems. Since faults are not available, those are considered as unknown inputs. Unknown input observers can estimate states without full information of inputs if some conditions are satisfied. The authors suggest a continuous-time extended UIO (eUIO) and prove the convergence of state estimation errors. Since the dynamic equation of a spacecraft is nonlinear, an extended UIO can be applied. Three eUIOs are designed to monitor three reaction wheels. The moving averages of each eUIO's residuals are selected for decision logic. The proposed method is verified by numerical simulations.

• 품질경영학회지
• /
• 제29권3호
• /
• pp.166-176
• /
• 2001

This paper considers a six sigma project for reducing the color variation of the monitor materials in a chemical plant. The project follows a disciplined process of five macro phases: define, measure, analyze, improve, and control (DMAIC). A process map is used to identify process input variables. Three key process input variables are selected by using an input variable evaluation table; a melting pressure, a coloring agent, and a DP color variation. DOE is utilized for finding the optimal process conditions of the three key process input variables. The sigma level of defects rate becomes a 4.58 from a 2.0 at the beginning of the project.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 F
• /
• pp.2656-2658
• /
• 1999

This paper presents a control scheme for a three-phase PWM converter system without any voltage sensors. Two input currents and one load current are measured. In a general PWM converter system, the required AC input and DC output voltage values in order to control the converter are estimated using the differential equations of the converter from the measured input currents and load current values in the switch modes of the converter circuit. The PI controller is used as DC voltage controller and sinusoidal tracking controller which tracks directly AC input current is used as input current controller. The Proposed method is verified by simulations. This paper describes the estimation method and configuration of the controller, and discusses steady state and transient performances of the converter