• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 춘계학술대회논문집
• /
• pp.56-62
• /
• 2000

Semi-solid forming process has some advantages such as successful manufacturing of high quality components with less inner defects suitable for less machining high productivity and energy-saving effect. the thixotropic behavior(solid-like in the unperturbed state and liquid-like during shearing) has been the basis for the semi-solid forming process. The main focus of this article is the investigation of the effect of T6 heat treatment and alloying elements on the mechanical properties in the semi-solid formed products using thixotropic hypoeutectic (A357 and ALTHIX 86S) and hypereutectic(A390) materials. The new methods to produce semi-solid formed components with high quality are also proposed and discussed in terms of a die design and the development of a lubricant.

• 한국세라믹학회지
• /
• 제40권7호
• /
• pp.632-636
• /
• 2003

To prepare the alumina cement free vibrated alumina castable, $\rho$-alumina is employed as a binder material, and nano-sized clay is added to enhance the curing strength and give thixotropic behavior. The rheological behavior of matrix of castable is controlled by investigating the influences of ultrafines, $\rho$-alumina, and nano-sized clay on the viscosity of matrix. The microsilica and ultrafine alumina were added 3 wt% and 4 wt%, respectively to the matrix, which showed that the viscosities tends to be lowest values. The rheological property of the matrix is well established by adding $\rho$-alumina as 8 wt% and clay as 4 wt%. The thixotropic behavior of the $\rho$-alumina bonded castable was appeared by introducing nano-sized clay into the matrix and adjusting the pH near to the PZC of the clay suspension.

• Computers and Concrete
• /
• 제15권1호
• /
• pp.73-88
• /
• 2015

Following previous studies, the current paper describes the results of an experimental program concerning the repair of reinforced concrete columns by thixotropic pseudo plastic mortar, preformed to analyze and quantify the influence of initial construction damage to the behavior of the repaired element. Five columns (section scale 1:2) were designed according to the minimum requirements of reinforcement of ductility orientated codes' design with variables the percentages of initial construction damages. All were tested in axial compression with repeated cycles up to failure. For comparison reasons, another one of the same characteristics, yet healthy, was constructed and tested as a reference specimen. A numerical study (Finite Element Analysis) was conducted for further investigation of the behavior of the thixotropic mortar as repair material. The results indicate that: a) surpassing a specific amount of damage, columns even suitably repaired present lower strain capacity, b) finite element analysis present the same way of deboning of the repaired material taking into consideration the buckling of the reinforcement bars.

• 한국세라믹학회지
• /
• 제36권12호
• /
• pp.1281-1286
• /
• 1999

• 신재생에너지
• /
• 제8권1호
• /
• pp.18-23
• /
• 2012

The screen printing has been widely used to form silver electrodes in solar cell device due to their simplicity of process. However, the wavy and irregular surface which is believed to be originated from a screen mask mesh and thixotropic characteristics of paste on screen printing process is well-known to give a negative effect on solar cell efficiency. The dispensing method that the silver paste is extruded through micro nozzle under a moderate pressure and coated on substrate can form the silver electrode without any wavy surface. In this study, we optimize the composition of silver paste and develop paste blending condition based on the thixotropic behavior of paste. The optimized paste shows a large thixotropic loop area which is related to an aspect ratio of electrode line and has the viscosity of 40 $Pa{\cdot}s$ at 40 s-1. The electrode line we finally obtainis 67.2 ${\mu}m$ in width and has an aspect ratio of 0.277.

• 한국식품과학회지
• /
• 제17권3호
• /
• pp.141-145
• /
• 1985

가열산화된 식용 콩기름시료(가열온도 : $180^{\circ}C$, 가열시간 : 7시간, 공기주입속도 : 120 ml/min)를 여러 측정온도에서 320 rpm에서 904 rpm의 넓은 전단속도 범위에서 그 유동곡선을 얻어 그 유동학적 특성을 조사하였던바 틱소트로피 유체의 특성을 나타내었다. 또한 전단속도가 증가함에 따라, 그리고 측정온도가 낮아짐에 따라(측정온도범위 : $13{\sim}37^{\circ}C$) 틱소트로피의 유채 특성을 더 강하게 나타내었다. 한편 가열산화된 콩기름 시료의 유동학적 특성을 반복하여 측정하고저 할 때에는 최소한 1시간 이상의 "휴식기"를 두어야 그 유동학적 특성이 완전히 회복됨을 알 수 있었다. 평형상태에서 가열산화된 콩기름 시료의 유동학적 특성을 정량적으로 나타내기 위해서 틱소트로피계수(coefficient of thixotropy)와 유사성이 있는 틱소트로피 기울기(thixotropic slope)를 적용하였으며 이들은 유동학적 특성에 관한 본 연구의 실험결과들을 만족스럽게 예측하여 주었다.

• Elastomers and Composites
• /
• 제44권3호
• /
• pp.323-328
• /
• 2009

고분자 용융 같은 물질의 유변학적인 성질은 전단 흐름에서 복잡한 비 뉴톤 유동 현상을 보인다. 이들 유동성질은 유동단위와 유동부분 사이의 상호작용의 특성에 의하여 결정된다. poly(vinyl alcohol) hydrogel의 비 뉴톤유동 곡선을 cone-plate 레오메타로 여러 온도와 여러 농도 조건에서 얻었다. PVA hydrogel의 유동 곡선을 비 뉴톤 유동식에 적용시켜 유동 파라메타를 얻었다. 유동현상은 전단 속도가 증가함에 따라 전단박화의 틱소트로피 현상을 나타내었다.

• 한국결정성장학회:학술대회논문집
• /
• 한국결정성장학회 1998년도 PROCEEDINGS OF THE 15TH KACG TECHNICAL MEETING-PACIFIC RIM 3 SATELLITE SYMPOSIUM SESSION 4, HOTEL HYUNDAI, KYONGJU, SEPTEMBER 20-23, 1998
• /
• pp.79-83
• /
• 1998

Plasma display panel is a potential candidate for HDTV, due to the fact hat the expansion of screen size is much easier using thick film technology. In this study, transparent dielectric materials using lead borosilicate glasses is developed, which satisfy the requirements of dielectrics for PDP. Paste is made of this glass composition. The paste has thixotropic behavior suitable for screen printing. The paste shows more thixotropic behavior as the particle size decrease. After firing, cross sectional area was analyzed by SEM. The void of fired thick film was removed using bimodal particle system. The dielectric showed good adhesion characteristics.

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2003년도 춘계총회 및 연구발표회 초록집
• /
• pp.138.2-138
• /
• 2003

• 한국유변학회:학술대회논문집
• /
• 한국유변학회 2001년도 춘계 학술발표회 논문집
• /
• pp.73-76
• /
• 2001