• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2005년도 학술발표회(2)
• /
• pp.902-903
• /
• 2005

• 대한기계학회논문집B
• /
• 제27권3호
• /
• pp.294-301
• /
• 2003

We examine a problem in which porous/viscoelastic compliant thin plates are subject to pressure fluctuations under transitional or turbulent boundary layer. Measurements are presented of the frequency spectra of the near-field pressure and radiated sound by compliant surface. A porous plate consisting of 5mm thick. open-cell foam with fabric covering and a viscoelastic-painted plate of 1mm thick over an acoustic board of 4mm thick were placed over a rigid surface in an anechoic wind tunnel. Streamwise velocity and wall pressure measurements were shown to highly attenuate the convective wall pressure energy when the convective wavenumber (k$_{c}$h) was 3.0 or more. The sound source localization on the compliant walls is applied to the measurement of radiated sound by using an acoustic mirror system.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.779-782
• /
• 2002

We examine the problem in which porous/viscoelastic compliant thin plates are subject to pressure fluctuations under transitional or turbulent boundary layer. Measurements are presented of the frequency spectra of the near-field pressure and radiated sound by compliant surface. A porous plate consisting of 5mm thick, open-cell foam with fabric covering and a viscoelastic painted plate of 1mm thick over an acoustic board of 4m thick were placed over a rigid surface in an anechoic wind tunnel. Streamwise velocity and wall pressure measurements were shown to highly attenuate the convective wall pressure energy when the convective wavenumber ($k_{ch}$) was 3.0 or more. The sound source localization on the compliant walls is applied to the measurement of radiated sound by using an acoustic mirror system.

• Journal of the Korean Wood Science and Technology
• /
• 제16권1호
• /
• pp.9-20
• /
• 1988

Lespedeza species have been widely used not only as plant resources for bark, leaves and honey, but also as erosion control materials. This study was carried out to investigate the structural and wood tiber characteristics in order to obtain basic information for the utilization of the wood. The wood structure was investigated for 10 selected species and the wood fiber, for the 5 selected species among Lespedeza species distributed all over the country. The following results were obtained. In the cross section, campylotropis showed ray diffuse porous wood, L. bicolor, L. cyrtobotrya, L. thunbergii var. intermedia, diffuse porous wood, and L. tomentella, L. angustifolioides. L. maritima, L. robusta, L. patentibicolor, ring porous wood. The maximum diameter of a single vessel ranged 66-123 ${\mu}$ in all species. Campylotropis showed the most number of vessels, L. angustifolioides, the least. The number of ray per mm ranged 7-22, Campylotropis showed the most number of rays, L. angustifolioides, the least. In the radial section the average length of vessel ranged 121-250 ${\mu}$ in all species. L. thunbergii var. intermedia showed the longest vessel, L. tomentella, the shortest. In tangential section the average width of the uniseriate ray ranged 9.2-14.7${\mu}$, that of the multiseriate ray, 19.2-42.1 ${\mu}$. The average height of the uniseriate ray ranged 143.0-1162.0 ${\mu}$. The width of fiber ranged 10.12-13.61 ${\mu}$, L. maximowiezii showed the narrowest tiber, L. thunbergii var. intermedia. the widest, the thickness of fiber wall ranged 2.93-3.71 ${\mu}$ in the five species. L. maximowiezii showed the most thin fiber wall, L. thunbergii var. intermedia, the thickest, L. cyrtobotrya showed the difference in the size of fiber between the shade and the sunny sites but L. maximowiezii showed no difference. There was significant difference in fiber length, fiber width and wall thickness between L. eyrtobotrya and L. maximowiezii.

• 한국재료학회지
• /
• 제18권10호
• /
• pp.529-534
• /
• 2008

The hydrogen gas sensing properties of a zinc oxide nanowire structure were studied. Porous zinc oxide nanowire structures were fabricated by oxidizing zinc deposited on a single-wall carbon nanotube (SWNT) template. This revealed a porous ZnO-SWNT composite due to the porosity in the SWNT film. The gas sensing properties were compared with those of zinc oxide thin films deposited on SiO2/Si substrates in sensitivity and operating temperature. The composite structure showed higher sensitivity and lower operating temperature than the zinc oxide film. It showed a response even at room temperature while the film structure did not.

• 한국가구학회지
• /
• 제18권4호
• /
• pp.261-267
• /
• 2007

This report describes the wood anatomy and 1% safranine solution penetration depth in radial and longitudinal directions of Anthocephalus chinensis belonging to the family Rubiaceae native to Bangladesh. The wood of this species was mostly characterized by diffuse porous, vessel with simple perforation plate, vestured alternate intervessel pittings, relatively medium vessel elements and fiber, and nonseptate fiber with distinctly bordered pits at radial wall. The body ray cell was procumbent with 2 to over 4 rows of upright and square marginal cells. Sometimes, the rays with procumbent, square and upright cells were mixed. Latewood fiber was thin to thick walled while it was very thin walled in earlywood. Axial parenchyma was diffuse, vasicentric, 5-8 cells per parenchyma strand dominantly present. Liquid penetration depth was observed in radial and longitudinal directions at moisture level of 7.42%. Longitudinal penetration was found 6.3 times higher than radial penetration. The initial penetration rate of safranine solution was high, but gradually decreased during the course of time. Different anatomical features were found to be responsible for the variation of safranine solution penetration depth compared to Gmelina arborea.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2009년도 하계학술발표대회 논문집
• /
• pp.645-649
• /
• 2009

Liquid desiccant cooling technology can supply cooling by using waste heat and solar heat which are hard to use effectively. For compact and efficient design of a dehumidifier, it is important to sustain sufficient heat and mass transfer surface area for water vapor diffusion from air to liquid desiccant on heat exchanger. In this study, the plate type heat exchanger is adopted which has extended surface, and hydrophilic coating and porous layer coating are adopted to enhance surface wettedness. PP(polypropylene) plate is coated by porous layer and PET(polyethylene terephthalate) non-woven fabric is coated by hydrophilic polymer. These coated surfaces have porous structure, so that falling liquid film spreads widely on the coated surface foaming thin liquid film by capillary force. The temperature of liquid desiccant increases during dehumidification process by latent heat absorption, which leads to loss of dehumidification capacity. Liquid desiccant is cooled by cooling water flowing in plate heat exchanger. On the plate side, the liquid desiccant can be cooled by internal cooling. However the liquid desiccant on extended surface should be moved and cooled at heat exchanger surface. Optimal mixing and distribution of liquid desiccant between extended surface and plate heat exchanger surface is essential design parameter. The experiment has been conducted to verify effective surface treatment and distribution characteristics by measuring wall side flow rate and visualization test. It is observed that hydrophilic and porous layer coating have excellent wettedness, and the distribution can be regulated by adopting holes on extended surface.

• 대한두개안면성형외과학회지
• /
• 제20권3호
• /
• pp.164-169
• /
• 2019

Background: The conventional surgical method for reconstructing orbital floor fractures involves restoration of orbital continuity by covering an onlay with a thin material under the periorbital region. However, in large orbital floor fractures, the implant after inserting is often dislocated, leading to malposition. This study aimed to propose a novel implanting method and compare it with existing methods. Methods: Among patients who underwent surgery for large orbital floor fractures, 24 who underwent the conventional onlay implanting method were compared with 21 who underwent the novel ${\gamma}$ implanting method that two implant sheets were stacked and bent to resemble the shape of the Greek alphabet ${\gamma}$. When inserting a ${\gamma}$-shaped implant, the posterior ledge of the orbital floor was placed between the two sheets and the bottom sheet was impacted onto the posterior wall of the maxilla to play a fixative role while the top sheet was placed above the residual orbital floor to support orbital contents. Wilcoxon signed-rank test and Mann-Whitney U test were used for data analyses. Results: Compared to the conventional onlay method, the gamma method resulted in better restoration of orbital contents, better improvement of enophthalmos, and fewer revision surgeries. Conclusion: Achieving good surgical outcomes for extended orbital floor fractures is known to be difficult. However, better surgical outcomes could be obtained by using the novel implantation method of impacting a ${\gamma}$-shaped porous polyethylene posteriorly.

• 한국가구학회지
• /
• 제17권3호
• /
• pp.29-36
• /
• 2006

Juvenile and matured wood of Populus tomentiglandulosa species of Salicaceae native grown in Korea was observed by FE-SEM and optical microscope. Species is characterized by mostly diffuse-porous, simple perforation plates, polygonal alternate non-vestured intervessel pit, medium length of vessel elements and fibres, non-septate very thin walled libriform fibres and exclusively uniseriate procumbent rays. Axial parenchyma was absent or extremely rare. Vessel and fibre length were longer in both matured and juvenile latewood than those of earlywood. Ray cell lumen diameter, ray length, number and diameter of endwall pit in ray cell, endwall pit, number and diameter of pit in lateral wall of one ray parenchyma cell, vessel ray pit number and diameter vary from juvenile early and latewood to matured wood.

• 한국항공우주학회지
• /
• 제34권12호
• /
• pp.18-24
• /
• 2006

슬롯과 다공판을 이용한 충격파와 난류 경계층 간섭유동의 피동제어에 관한 연구가 수행되었다. 슬롯의 다양한 형상 변화가 간섭유동에 미치는 영향이 관찰되었으며, 이를 위하여 간섭유동 후방에서 피토/벽압력 분포 및 쉴리렌, 유맥선, 오일막 간섭 줄무늬 형상과 같은 유동가시화 결과 등이 얻어졌다. 유동방향의 슬롯의 경우 간섭유동 후방에서 제어되지 않은 경우와 비교하여 보다 높은 피토압력이 국소적으로 관찰되었으나, 폭방향 슬롯제어는 전체적으로 제어되지 않은 경우에 비하여 피토압력 크기에서 큰 장점을 보이지 않았다.