• 전자공학회지
• /
• 제17권6호
• /
• pp.53-60
• /
• 1990

본 글은 완성된 circuit를 thick-film hybrid IC화 하기 위하여 고려하여야 할 사항인 설계의 기본개념, 기판 재질의 소개 및 특성, 도체, 저항, 유전체 paste를 소개하고 제조 기술 분야에서는 기본공정인 인쇄, 소성, 트리밍, packaging에 대하여 기술하였다.

• Journal of Welding and Joining
• /
• 제18권6호
• /
• pp.96-101
• /
• 2000

Sintered alumina ceramic substrate has been used for the insulating substrate for thick Hybrid IC owing to its cheapness and good insulating properties. Some of thick HIC's are important to eliminate the heat emitted from the parts that are mounted on the ceramic substrate. Sintered ceramic substrate can not transfer and emit the heat efficiently. It's been tried to do plasma spray coating of alumina ceramic on the metal substrates that have a good heat emission property. The most important properties to commercialize this ceramic coated metal substrate are surface roughness and deposition efficiency. In this study, plasma spray coating parameters are optimized to minimize the surface roughness and to maximize the deposition efficiency using Taguchi experimental method. By this optimization, the deposition efficiency was greatly improved from 35% at the frist time to 75% finally.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1993년도 추계학술대회 논문집
• /
• pp.49-54
• /
• 1993

This paper discusses the reliability of solder joints of electronic devices on printed circuit board. Solder application is usually done by screen printing method for the bonding between outer leads of devices and thick film(Ag/Pd) pattern on Hybrid IC as wel1 as Cu lands on PCB. As result of thermal stresses generated at the solder joints due to the differences of thermal expansion coefficients between packge body and PCB, Micro cracking often occurs due to thermal fatigue failure at solder joints. The initiation and the propagate of solder joint crack depends on the environmental conditions, such as storage temperature and thermal cycling. The principal mechanisms of the cracking pheno- mana are the formation of kirkendal void caused by the differences in diffusion rate of materials, ant the thermal fatigue effect due to the differences of thermal expansion coefficient between package body and PCB. Finally, This paper experimentally shows a way to supress solder joints cracks by using low-${\alpha}$ PCB and the packages with thin lead frame, and investigates the phenomena of diffusion near the bonding interfaces.

• 대한전자공학회논문지
• /
• 제9권5호
• /
• pp.27-33
• /
• 1972

This paper describes the computer-aided design, fabrication and performance of high Q and high gain active filters suitable for microminiaturization in the frequency range of 10-800MHz, based on the negative resistance operation of a transistor. 48 as high as 1000 and a transducer gain as high as 35dB can readily be obtained with a single-transistor amplifier and with an inductance as small as a few nH at higher frequencies and 150 nH at lower frequencies in tile above frequency range. The gain of the proposed active filter can be stoabilized within $\pm$ 1.5 dB over the temperature range -1$0^{\circ}C$ to +5$0^{\circ}C$ and the temperature dependence of the center frequency is tapicalla 50ppm/$^{\circ}C$. An experimental FM receiver utilizing these fitters and operating at a carrier frequency of 92 MH3 was built. The whole circuit was fabricated on eight alumina substrates of by the thick-film hybrid IC technique and the coils are constructed, for miniaturization, in a spiral form of 3 or 4 turns of enamel copper wire with an overall diameter of about 5mm. The test results are also reported in this paper.

• 센서학회지
• /
• 제2권1호
• /
• pp.19-27
• /
• 1993

본 논문은 $n^{+}$ 에피택셜층을 이용한 전기화학 에칭스톱과 글라스-실리콘의 양극 접합기술을 이용하여 저 압력측정을 위한 용량형 압력센서를 제작한 것이다. 제작된 센서는 하이브리드형으로 센서 커패시터와 기준 커패시터를 갖는 센서 칩과 두가지 출력검출회로 칩으로 구성되어 있다. 이 제작된 센서는 다이아프램 크기가 $1.0{\times}1.0 mm^{2}$이고, 두께가 $10{\mu}m$로 제작된 센서는 압력이 인가되지 않을 때 용량의 크기가 7.1 pF이고, 10 KPa 압력에서 감도가 5.2 %F.S.이다. 또 용량을 전압으로 검출하는 컨버터회로를 이용할 경우, $5{\sim}45^{\circ}C$ 온도범위에서 영점 온도특성과 감도 온도특성은 각각 0.051 %F.S./$^{\circ}C$와 0.12 %F.S./$^{\circ}C$ 이다.