• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2004년도 하계종합학술대회 논문집(2)
• /
• pp.387-390
• /
• 2004

Thick film alcohol gas sensors were fabricated. Their electrical properties and gas sensing characteristics were investigated. The sensitivity of $1wt.\%$ Pd-doped ${\gamma}-Fe_2O_3$ thick film heat treated at $400^{\circ}C$, 2hrs was $74\%$ to 500ppm alcohol gas at the operating temperature of $250^{\circ}C$. The selectivity of the film to alcohol was good. It showed fast response time to low concentrations of alcohol in air, hence this sensor can be used as a breath sensor.

• 센서학회지
• /
• 제20권2호
• /
• pp.114-117
• /
• 2011

A thick 25 ${\mu}m$ thickness poled P(VDF/TrFE) film pyroelectric infrared ray sensor has been fabricated and then thin 1.6 ${\mu}m$ thickness P(VDF/TrFE) film pyroelectric infrared ray sensor has been fabricated also. These thick and thin P(VDF/TrFE) film pyroelectric infrared ray sensor was mounted in TO-5 housing to detect infrared light of 5.5 ~ 14 ${\mu}m$ wavelength for human body detecting with each other. The noise output voltage of the thick P(VDF/TrFE) film pyroelectric infrared ray sensor were 380 mV and NEP(noise equivalent power) is $3.95{\times}10^{-7}$ W which is the similar value with the commercial pyroelectric infrared ray sensor using ceramic materials as a sensing material. The NEP and specific detectivity $D^*$ of the thin P(VDF/TrFE) film pyroelectric infrared ray sensor were $2.13{\times}10^{-8}$ W and $9.37{\times}106$ cm/W under emission energy of 13 ${\mu}W/cm^2$ respectively. These result caused by lower thermal diffusion coefficient of a thin 1.6 ${\mu}m$ thickness PVDF/TrFE film than the thick 25 ${\mu}m$ thickness poled P(VDF/TrFE) film pyroelectric infrared ray sensor.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.656-658
• /
• 2004

Pb$(Zr_{0.8}Ti_{0.2})TiO_3$ powder were prepared by the sol-gel method using a solution of Pb-acetate, Zr n-propoxide and Ti iso-propoxide. PZT thick film were fabricated by the screen printing method, and the structural and ferroelectric properties asafunting of the sintering temperature were studied. PZT film thickness, obtained by four screen printing, was approximately $70\sim90{\mu}m$. The relative dielectric constant and the dielectric loss of the PZT thick film sintered at $1050^{\circ}C$t were approximately 676 and 1.4%, respectively. The remanent polarization and the coercive field of the PZT thick film sintered at $1050^{\circ}C$ were $21.15{\mu}C/cm^2$ and 10.1 kV/cm, mapetively

• E2M - 전기 전자와 첨단 소재
• /
• 제9권8호
• /
• pp.819-824
• /
• 1996

We have investigated the temperature dependence of CO gas sensitivity for ZnO and ZnO-CuO thick films at 200 ppm CO gas, where those films were prepared by thermal transformation. The ZnO thick film shows the maximum sensitivity of -4 at >$300^{\circ}C$ On the other hand, ZnO-CuO(more than 1mol%) thick film shows that the maximum sensitivity reduced to less than 1.5. The decrease in sensitivity of CO gas with increasing the CuO contents is due to the decrease of the oxygen absorption in thick films.

• Transactions on Electrical and Electronic Materials
• /
• 제6권4호
• /
• pp.186-189
• /
• 2005

We have fabricated superconducting HTSC ceramic thick films by chemical process. c-axis oriented HTSC thick films have been attempted bi-axially textured Ni tapes. The x-ray diffraction pattern of the HTSC thick films contained superconducting phase crystal. The critical temperature and critical current density was 110K.

• Journal of Electrical Engineering and Technology
• /
• 제2권3호
• /
• pp.408-412
• /
• 2007

It is almost impossible to secure the reproductibility and stability of a commercial Thick-Film Metal Oxide Semiconductor Gas Sensor since it is very difficult to keep the consistency of the manufacturing environment. Thus it is widely known that the general Semiconductor-Oxide Gas Sensors are not appropriate for precise measurement systems. In this paper, the output characteristic analyzer of the various Thick-Film Metal Oxide Semiconductor Gas Sensors that are used to recognize the air quality within an automobile are proposed and examined. The analyzed output characters in a normal air chamber are grouped by sensor ranks and used to fill out the characteristic table of the Thick-Film Metal Oxide Semiconductor Gas Sensors. The characteristic table is used to determine the rank of the sensor that is equipped in the current air cleaner system of an automobile. The proposed air control system can also adapt the on-demand operation that recognizes the history of the passenger's manual-control.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 1999년도 High Temperature Superconductivity Vol.IX
• /
• pp.242-246
• /
• 1999

For the fabrication of fault current limiting device using HTSC thick film, YBa$_2Cu_3O_x$ superconducting thick film was formed by surface diffusion process of the Y$_2BaCUO_5$ and the mixed compound of (3BaCuO$_2$+2CuO) expected to be liquid phase above the peritectic temperature of YBa$_2Cu_3O_x$. For the surface diffusion, the compounds of 3BaCuO$_2$+2CuO mixed with binder material was patterned on Y$_2BaCUO_5$ substrate by the screen printing method. After proper sintering, the characteristics of current limit on thick film fabricated was measured. The thick film was able to limit the current from 2.8213 mA$_{rms}$nu to 4.2034 mA$_{rms}$ with 500${\omega}$ load resistance, and from 4.1831 mA$_{rms}$ to 4.2150 mA$_{rms}$ with 10${\omega}$ load resistance.

• 한국세라믹학회지
• /
• 제48권1호
• /
• pp.106-109
• /
• 2011

In order to fabricate 8YSZ thick film by silk screen printing, YSZ(yttria-stabilized zirconia) commercial powder was used as starting materials. Paste for screen printing was made by mixing 8YSZ powder and organic vehicles. 8YSZ thick film was formed on $Al_2O_3$ substrate. The crystal structure, and microstructure were investigated. Grain size of 8YSZ was increased with increasing calcination temperature and rapid grain growth was shown after calcination at $1300^{\circ}C$. Microstructure showed the mixture of large and small grain size after $1400^{\circ}C$ sintering. Shrinkage rate of 8YSZ thick film sintered at $1400^{\circ}C$ was more than 40%.

• Macromolecular Research
• /
• 제12권4호
• /
• pp.391-398
• /
• 2004

Thick-film photolithography is a new technology that combines lithography processes, such as exposure and development, with the conventional thick-film process applied to screen-printing. In this study, we developed a low-temperature cofireable silver paste applicable for thick-film processing to form fine lines using photolitho-graphic technologies. The optimum paste composition for forming fine lines was investigated. The effect of processing parameters, such as the exposing dose, had on the fine-line resolution was also investigated. As the result, we found that the type of polymer and monomer, the silver powder loading, and the amount of photoinitiator were the main factors affecting the resolution of the fine lines. The developed photoimageable silver paste was printed on a low-temperature cofireable green sheet, dried, exposed, developed in an aqueous process, laminated, and then fired. Our results demonstrate that thick-film fine lines having widths < 20 $\mu\textrm{m}$ can be obtained after cofiring.

• 한국전기전자재료학회논문지
• /
• 제23권2호
• /
• pp.118-123
• /
• 2010

The eco-friendly technologies have been extended as matter of international concern due to various diseases and syndromes according to an environmental pollution. In this study, we have manufactured a ceramic cluster with thick film type for anion generation equipment which is maximized anion but minimized ozone contents generated. To develop the formulation of ceramic cluster, we conducted the $Mg_2SiO_4$ powders doped with 10 vol% glass frits as Na-Zn-B-O system and sintered at $1050^{\circ}C$ for 2 hours in air for starting materials and investigated the matching properties between the Ag-Pd electrode and the starting materials. The sintered sample for the composition of cluster has 6.7 of dielectric constant and 32 kV/mm of withstand voltage. The yield of anions was measured according to an electrode pattering, discharge gap between electrode, and thickness of electrode protective layer in the cluster of thick film type. We have manufactured the ceramic clusters with optimized thick film structure that have an anion over a hundred particles and the ozone of 0.6 ppb generated.