• Composites Research
• /
• 제25권1호
• /
• pp.19-25
• /
• 2012

본 연구에서는 압축하중을 받는 원공을 가진 샌드위치 복합재 기둥의 좌굴 거동을 조사하였다. 샌드위치 복합재 기둥은 유리섬유직물/에폭시 면재와 우레탄 폼 심재로 구성되어 있다. 이때 면재 두께는 1.7mm, 심재 두께는 23mm, 37mm, 48mm, 61mm, 그리고 원공 직경은 25mm와 38mm를 고려하였다. 원공 위치가 샌드위치 복합재 기둥의 좌굴 거동에 미치는 영향을 조사하기 위해 직경 25mm인 원공이 시편중앙부에 있는 경우, 시편중앙부를 기준으로 중앙부와 끝단 사이의 1/4 지점에 있는 경우, 시편중앙부를 기준으로 중앙부와 끝단 사이의 1/2 지점에 있는 경우를 고려하였다. 시편중앙부에 직경 25mm인 원공이 있는 경우의 좌굴하중과 최대하중은 원공이 없는 경우보다 10% 정도 낮게 나타나며, 시편중앙부에 직경 38mm인 원공이 있는 경우의 좌굴하중과 최대하중은 원공이 없는 경우보다 30% 정도 낮게 나타났다. 그러나 원공 위치가 좌굴하중과 최대하중에 미치는 영향은 크지 않았다. 주요 파괴 모드는 심재 두께가 23mm와 37mm와 같이 얇은 경우는 심재 전단파괴가 지배적이고 심재 두께가 48mm와 61mm와 같이 두꺼운 경우는 면재-심재 분리가 지배적으로 관찰되었다.

• 대한기계학회논문집A
• /
• 제25권11호
• /
• pp.1813-1819
• /
• 2001

Partial penetration welding Joint defines that groove welds without steel backing, welded from on side, and groove weeds welded from both sides but without back gouging, that is. it has an unwelded portion at the root of the weld. In this study we analysed fur residual stress and displacement distribution on partial penetration welding condition of thick plate metal. For 25.4mm thick plate, theoretical residual stress and displacement analysis by finite element method using ABAQUS was carried out and compared with the experimental result using hole-drilling method. In results of the condition of partial penetration, it appeared that longitudinal stress at welding area was a little difference and transverse stress did not have any effect by partial penetration multi-pass welding. From a point of welding distortion in partial penetration multi-pass welding, it seemed to be better to control root face smaller than 6.35mm.

• Journal of Welding and Joining
• /
• 제19권6호
• /
• pp.636-642
• /
• 2001

Partial penetration welding joint defines the groove welds that applies the one side welding which does not use steel backing and both side welding without back gouging, that is, the partial penetration welding joint leaves an unwelded portion at the root of the welding area. In this study, we analyzed the residual stress and fracture on the thick metal plates that introduced the partial penetration welding method. As results of using above mentioned welding method, we could draw a conclusion that longitudinal stress and traverse stress occurred around the welding area was so minimal and did not affect any influence. We also performed the fracture behavior evaluation on the partial penetration multi-pass welding with 25.4mm thick plate by using theJ-integral, which finally led us the conclusion that the partial penetration multi -pass welding method is more applicable and effective in handling the root face with less than 6.35mm.

• 대한기계학회논문집A
• /
• 제30권4호
• /
• pp.473-480
• /
• 2006

This paper explains analytical and experimental studies to evaluate the natural frequency of a composite carbody of Korean tilting train. The composite carbody with length of 23m was manufactured as a sandwich structure composed of 40mm-thick aluminium honeycomb core and 5mm-thick woven fabric carbon/epoxy face. From the finite element analysis, the 1st bending and 1st twisting natural frequency of the composite carbody were 11.67Hz and 14.4Hz, respectively. In order to verify the analytical results, the natural frequency measuring tests were performed. The measured 1st bending and twisting natural frequencies of the composite carbody were 10.25Hz and 11.0Hz, respectively. Both of these results satisfied the design requirement.

• 대한조선학회논문집
• /
• 제32권1호
• /
• pp.132-140
• /
• 1995

선체의 중량을 감소시키기 위한 구조적인 형식중의 하나가 샌드위치 type이고 고속선의 면재는 F.R.P.와 Kevlar/Epoxy를, 심재로는 P.V.C.foam을 많이 사용한다. 본 연구에서는 면재의 두께가 두껍고 윗면재와 아랫면재의 두께가 다른 비대칭인 경우에 대하여 Rayleigh-Ritz의 에너지방법으로 해석하였다. 그리고 얇은 면재와의 비교를 위하여 등방성이고 중립축에 대칭인 평판을 기준하여 굽힘응력, 전단응력, 국부적인 굽힘응력, 막응력효과를 고려한 응력들을 면재2종류와 심재3종류에 대해서 비교하고 해석하였다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 추계학술발표대회 논문집
• /
• pp.234-238
• /
• 2005

This paper explains the fatigue test procedure of a composite train carbody. The composite carbody with length of 23m was manufactured as a sandwich structure composed of a 40mm-thick aluminium honeycomb core and 5mm-thick woven fabric carbon/epoxy face. In order to evaluate fatigue strength of the composite carbody, the carbody will be excited by two 50-ton capacity hydraulic actuators. The excitation frequency will be measured by natural frequency evaluation test under full weight condition. The test The fatigue test is to be conducted For $2{\times}10^6$cycles. During the fatigue test, the nondestructive tests using X-ray and liquid penetrant will be performed. From crack detection tests, the location and Fatigue crack progress will be investigated.

• 한국전기전자재료학회논문지
• /
• 제23권2호
• /
• pp.153-158
• /
• 2010

The crystallization of FePt/MgO(001) magnetic thin films of various thicknesses has been studied using synchrotron x-ray scattering, atomic force microscope, and vibrating sample magnetometer. In film with a 499-$\AA$-thick, face-centered tetragonal, ordered FePt phase was dominantly crystallized into perpendicular (001) grains keeping the magnetically easy c-axis normal to the film plane during annealing. In film with a 816-$\AA$-thick, however, longitudinal (110) grains keeping the c-axis parallel to the film plane were grown on top of the perpendicular (001) grains. The behavior of the magnetic properties was consistent with the thickness dependence of the crystallization. We attribute the thickness dependence of the crystallization to the substrate effect, which prefers the growth of the c-axis oriented perpendicular grains near the film/substrate interfacial area.

• 한국정보과학회논문지:소프트웨어및응용
• /
• 제30권7_8호
• /
• pp.773-779
• /
• 2003

얼굴 영역의 정확한 위치를 정확히 찾는 것은 얼굴 인식을 위한 핵심적인 전처리 과정이다. 본 논문에서는 조명조건, 표정, 배경의 변화에 무관하게 얼굴의 구성요소를 검출할 수 있는 강건한 기법을 제안한다. 수평 방향의 상대적으로 어두운 화소값을 갖는 눈썹, 눈, 입 둥과 같은 독립된 얼굴 요소를 검출하기 위해 형상 분해 국부 최적 임계치 기법을 적용하며 얼굴을 구성하는 간단한 기하학적 조건을 만족하는 얼굴 요소의 그룹을 검색함으로써 순수 얼굴영역을 검출한다. AR-face 데이타베이스의 영상에 적용한 결과, 두꺼운 안경테에 의해 눈썹이 가리워진 특수한 경우를 제외한 거의 모든 영상에 대해 정확한 얼굴 영역을 검출할 수 있었고, 얼굴의 대칭성을 이용해 회전과 이동 변화를 보상할 수 있으므로 강건한 얼굴 인식의 전처리 과정으로 사용할 수 있다.

• Journal of the Korean Wood Science and Technology
• /
• 제19권3호
• /
• pp.53-61
• /
• 1991

Mechanical properties of composite panel made with 3mm thick Apitong(Dipterocarpus grandiflorus) veneer on each face of particleboard core of 4 different specific gravity were determined. The results obtained were as follows: 1. Measured MOR and MOE increased with an increased in specific gravity of particleboard core. 2. Test results showed that the difference in bending properties between flatwise bending and edgewise bending was present. The average MOE value of flatwise loading was higer than that of epdgewise loading. But it was shown reverse tendency in MoR and MOE. 3. The delamination between face veneer and core particle was found in flatwise bending but nell in edgewise. 4. These composite panel could be substituted for plywood and other panel materials in furniture making as considered suitable allowable stress and bending strength.

• 한국결정성장학회지
• /
• 제11권3호
• /
• pp.106-111
• /
• 2001

The freestanding GaN substrates were grown by hydride vapor phase epitaxy (HVPE) on (0001) sapphire substrate and prepared by using laser induced lift-off. After a mechanical polishing on both Ga and N-surfaces of GaN films with 100$\mu\textrm{m}$ thick, their polarities have been investigated by using chemical etching in phosphoric acid solution, 3 dimensional surface profiler and Auger electron spectroscopy (AES). The composition of the GaN film measured by AES indicted that Ga and N terminated surfaces have the different N/Ga peak ratio of 0.74 and 0.97, respectively. Ga-face and N-face of GaN revealed quite different chemical properties: the polar surfaces corresponding to (0001) plane are resistant to a phosphoric acid etching whereas N-polar surfaces corresponding to(0001) are chemically active.