• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.10a
• /
• pp.351-352
• /
• 2006

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.57-62
• /
• 2000

Diagnosis or measurements using Infrared thermoimage hasn't been available. A quick diagnosis and thermal analysis can be possible when that kind of system is introduced to the investigation of each part. In this study, Infrared Camera, Thermovision 900 was used in order to investigate. Infrared Camera usually detects only Infrared wave from the light in order to illustrate the temperature distribution. Infrared diagnosis system can be applied to various field. Also, it is more effective to analyze temperature distribution on the welding parts during welding process. Especially, diagnosis using Infrared camera plays an important role on thermal analysis of Axle Casing Nut for Commercial Vehicles.

• Korean Chemical Engineering Research
• /
• v.47 no.6
• /
• pp.688-694
• /
• 2009

A spray-type cleaning agent in utilizing dust-remover on PCB was chosen to study the cleanliness test and efficiency. In order to choose alternative environmental-friendly cleaning agents, it is important that the systematic selection procedures should be introduced and applied through the evaluation of their cleaning ability, environmental characteristics, and economical factors, and that the objective and effective evaluation methods of cleanliness should be established for the industry. A novel cleaning evaluation method with scanning electron microscopy/energy-dispersive X-ray analysis of surface observation evaluation method and an infra-red thermography camera(THERMOVISION A20 model) was studied in this work. The sound card(CT-2770 model) cut by $2{\times}2cm$ size was used as a part, and before and after the spray cleaning, the cleanliness was observed by the image analyzer of SEM and further the removal efficiency of dust was quantitatively evaluated by the component analysis of EDX. For the parts of P4TE model motherboard and IPC-A-36 PCB plate, before and after the spray cleaning, temperature differences were measured and compared at room temperature and 50 oven temperature by an infra-red thermography camera in the contaminants of dust and iron powder.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.2
• /
• pp.301-305
• /
• 2010

Cutting procedures where qualities are determined by various demand factors largely influences shipbuilding productivity. Particularly, defects in cutting shapes and cutting surface results in delay for post shipbuilding stages such as in welding and assemblage lines which could become factors for reduced economic viability of the project. Existing cutting procedures utilize fossil fuels such as propane or ethylene as the main fuel component and these methods applied particularly to ship plate cutting gives relatively slow cutting speed and generates large quantities of harmful and sometimes poisonous polluting fumes of which warrants an urgent need to look for alternative cutting methods. Recent introduction of hydrox gas generated by electrically dissociating water into hydrogen and oxygen components to be utilize as an alternative cutting fuel has resulted not just in visible improvement on cutting quality and speed over the existing methods but it has also been welcomed as an environmentally friendly clean fuel source. This paper has been prepared to serve as the basis for accommodating this environmentally friendly hydrox gas cutting method into actual working environment by observing and recording hydrox gas cutting thermal characteristics.

• Fire Science and Engineering
• /
• v.28 no.6
• /
• pp.22-27
• /
• 2014

In this study a Fuel bed where surface fire spreads through is made to measure the data such as the flame height, radiation, spread rate and temperature distribution of Fuel bed. As experimental variables species of trees, wind velocities and slop are chosen. Fallen leaves of Quercus Variabilis (Q.V.) and Pinus Densiflora (P.D.) are used as fuel. Wind velocity is controlled by simply designed wind turnnel from 1 to 5 m/s. Slope of fuel bed is changed from $0^{\circ}$ to $30^{\circ}$. For the measurements of temperature distribution and spread rate total 35 of K-type 1.6 mm thermocouples are positioned as a lattice design. Radiant heat flow meters are used besides video camera and thermovision camera.