• Composites Research
• /
• 제36권5호
• /
• pp.315-320
• /
• 2023

오토클레이브를 사용하는 열경화성 탄소 섬유 복합재 성형 공정에서는 설정한 온도 사이클에 따라 내부 온도가 변화한다. 이 온도 변화에 따라 복합재 수지가 경화되며 성형이 진행된다. 이러한 과정에서 수지의 화학 반응으로 열이 발생하며, 이로 인해 오토클레이브 내부 온도와 복합재의 온도가 다를 수 있는 상황이 나타난다. 이전 연구에서는 복합재와 오토클레이브의 온도를 동일하게 가정하고, 성형 후에 발생하는 잔류 응력과 열 변형을 예측하였다. 그러나 잔류 응력과 열 변형은 복합재 온도와 경화도에 따라 영향을 받는 요소이기 때문에, 본 연구는 수지의 화학 반응열을 고려하여 정확한 온도와 경화도 변화를 계산하는 열화학 모델 해석 기법을 검증하였다. 또한, 이 모델이 다른 두께에서도 이와 같은 경향성을 나타내는지 확인하기 위해 두께별 케이스 연구를 하였다.

• Composites Research
• /
• 제20권5호
• /
• pp.13-19
• /
• 2007

섬유강화 열가소성수지 복합재료는 열경화성수지 복합재료의 강도 수준에 근접할 뿐만 아니라 열경화성수지 복합재료의 취약점으로 지적되고 있는 생산성, 리사이클, 내충격성 등이 우수하다. 일방향 섬유강화 복합재료의 강도계산을 위한 연구와 섬유배향상태를 측정하여 정량적으로 나타낼 수 있도록 연구하여 발표하였으나, 섬유함유율에 따른 섬유배향상태와 복합재료의 기계적 성질을 예측을 할 수 있는 데이터베이스 구축은 되어있지 않으므로 이에 대한 체계적인 연구가 필요하다 본 연구에서는 섬유함유율에 따른 섬유배향상태를 변화시켜 섬유강화 열가소성수지 복합판재를 제작한 후, 섬유함유율 및 섬유배향상태가 복합판재의 인장강도에 어떠한 영향을 주는지에 대해서 고찰하였다. 섬유강화 열경화성수지 복합재료의 $0^{\circ}$ 방향에서 인장강도 비는 등방성에서 이방성으로 갈수록 섬유배향함수와 섬유함유율에 관계없이 일정하게 나타났으나, $90^{\circ}$ 방향에서 인장강도 비는 인장 하중이 강화섬유 길이방향의 수직방향으로 작용했을 때 섬유필라멘트 분리에 의해 감소하였다.

• 한국표면공학회지
• /
• 제46권5호
• /
• pp.208-215
• /
• 2013

The aim of the present study was to improve the radiative heat dissipation of aluminum alloy, Al 1050. Resin/CuO coating and Cu/CuO composite plating were applied on aluminum alloy to improve the radiative heat dissipation. Resin/CuO coating was made using thermosetting silicon resin and Cu/CuO composite plating was made in pyrophosphate copper plating bath. Radiant heat flux($W/m^2$) was measured by self-produced radiant heat measurement device to compare each specimen. The cross section of specimen and chemical bonding of surface were analyzed by FE-SEM, XPS and FT-IR. As a result, radiant heat of Resin/CuO coating was higher than Cu/CuO composite plating due to the adhesion with aluminum plate and the difference in chemical bonding. But, Both of them were higher than aluminum alloy. In order to confirm the result of experiment, aluminum plate, Resin/CuO coating and Cu/CuO composite plating sample were applied LED and measured the LED temperature. As a result, LED temperature of samples were matched previous results and confirmed coated samples were lower about 10 degrees than the aluminum alloy.

• 한국철도학회논문집
• /
• 제12권6호
• /
• pp.1059-1066
• /
• 2009

근래에 와서 강화 플라스틱 복합재료의 생산과 함께 열경화성 수지 폐기물들의 양이 급격하게 증가하여 심각한 환경문제를 야기하고 있다. 우수한 기계적 물성을 지닌 유용한 열경화성 수지의 하나인 에폭시 수지는 열가소성 수지처럼 용융되거나 재 성형되지 않는다. 본 연구에서는 철도 차량용 탄소섬유 강화 에폭시 수지 복합재로부터 에폭시 수지를 분해하여 탄소섬유를 회수하는 일련의 실험을 수행하였다. 여러 분해공정들을 실험적으로 조사하여, 분해 효율과 회수되는 탄소섬유의 기계적 물성을 비교 검토하였다. 회수되는 탄소섬유가 서로 엉키는 것을 방지하기 위해서 각 복합재료 시편은 테플론 지지대로 고정시키고, 기계적인 교반을 가하지 않았다. 분해 생성물은 전자현미경(SEM), 기체 크로마토그라피 질량분석기(GC-MS) 및 만능재료시험기를 사용하여 분석하였다. 질산 수용액을 사용하는 분해 공정과 액상 및 기상 열분해 공정에서는 탄소섬유가 완전하게 회수되었다. 회수된 탄소섬유의 인장강도 감소율은 4% 미만으로 미미하였다.

• 한국재료학회지
• /
• 제3권2호
• /
• pp.140-144
• /
• 1993

열경화성 에폭시 수지의 물성 중 담약성을 개선하기 위해 새로운 반응성첨가제 succinonitrile(SN)을 Diglycidy1 ether of bisphenol A(DGEBA(-4,4'-methylene dianiline(MDA)계에 도입하여 현재 널리 사용되고 있는 유리섬유 복합재료에 매트릭스로 사용될 경우에 있어서 파괴되는 거동을 미시적으로 고찰하였다. 그 결과 post debond friction 에너지가 파괴 거동을 주도하고 있으며, 다음으로 pull-out에너지 그리고 debonding 에너지 순으로 나타났다. 따라서 파괴 거동에 미치고 있는 중요한 요인은 섬유와 매트릭스 간의 경계면 전단 응력이 크게 좌우함을 알 수 있었으며, 이때 반응성 첨가제 SN은 전단응력을 떨어뜨리는 것으로 고찰되었다.

• 한국염색가공학회지
• /
• 제32권4호
• /
• pp.245-254
• /
• 2020

The sheet molding compound composite has been applied divers section. This paper reports processing of carbon fiber reinforced thermosetting composite with diverse resins and which was composed of chopped carbon fiber (30 ~ 60 wt%). Normally the paste that the viscosity is over 15,000 cps has been used in traditional Sheet molding compound (SMC) machine. In this research, SMC machine was designed to make Carbon-sheet molding compound (C-SMC) prepreg which was composed with low viscosity resin (1,800 ~ 2,500 cps increase up to 10,000 cps after aging). In order to confirm the optimal processing condition. Mechanical strength tests including tensile test, shear test, impact test, flexural strength test were conducted on C-SMC composites. Plus we identified the correlation between the mechanical properties and prepreg processing condition (carbon ratio and applied resin).

• Advances in aircraft and spacecraft science
• /
• 제4권5호
• /
• pp.573-583
• /
• 2017

This paper presents a first step towards the understanding of water diffusion in RTM textile composite materials for aircraft applications and focuses on the development of experimental and numerical approaches to characterize the diffusion kinetics within the material. The method consists in making samples which are representative of the materials architecture and carrying out gravimetric tests on such samples. Analysis of results with the aid of a diffusion model reconstructing the architecture of the samples helps identifying the diffusion behaviour of the material.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.797-803
• /
• 2001

The on-line cure monitoring of fiber reinforced thermosetting resin matrix composite material was performed for the better quality and productivity during manufacturing. Since the dissipation factor measured by dielectrometry method is dependent on the degree of cure and temperature of resin, in this study, a new method to obtain the degree of cure during on-line cure monitoring for glass/polyester composites was developed by employing a combination function of the temperature and the dissipation factor. Two sensor signals from a K-type thermocouple and an interdigitated dielectric sensor were processed during curing process under various cure cycles. The DSC (Differential Scanning Calorimetry) data was also used for the reference of degree of cure.

• Structural Engineering and Mechanics
• /
• 제76권5호
• /
• pp.613-618
• /
• 2020

Exhausting oil resources and increasing pollution around the world are forcing researchers to look for new, renewable, biodegradable materials to lead sustainable development. The use of fiber reinforced composites based on natural fibres has increasingly begun as prospective materials for various engineering applications in the automotive, rail, construction and aerospace industries. The natural fiber chosen to make the composite material is plant-based fibre, e.g. jute fibre, and hemp fibre. Thermosetting polymer based Epoxy (LY556) was utilized as matrix material and The composites were produced using hand lay-up technique. The fabricated composites were tested for acoustic testing, thermo-gravimetric analysis (TGA) and flammability testing to asses sound absorption, thermal decomposition and fire resistivity of the structures. Hemp fibre composites have shown improved thermal stability over Jute fibre composites. However, the fire resistance characteristics of jute fibre composites are better as compared to hemp fibre composites. The sound absorption coefficient of composites was found to enhance with the increase of frequency.

• Journal of the Korean Wood Science and Technology
• /
• 제29권3호
• /
• pp.47-58
• /
• 2001

For finding both ways of recycling the wood and plastic wastes and solving the problem of free formaldehyde gas emission through manufacturing wood particle-polypropylene fiber composite board without addition of formaldehyde-based thermosetting resin adhesive, control particleboards and nonwoven web composite boards from wood particle and polypropylene fiber formulation of 50 : 50, 60 : 40, and 70 : 30 were manufactured at density levels of 0.5, 0.6, 0.7, and 0.8 g/$cm^3$, and were tested both in the physical and mechanical properties according to ASTM D 1037-93. In the physical properties, control particleboard had significantly higher moisture content than composite board. In composite board, moisture content decreased with the increase of target density only in the board with higher content of polypropylene fiber and also appeared to increase with the increase of wood particle content at a given target density. Control particleboard showed significantly greater water absorption than composite board and its water absorption decreased with the increase of target density. In composite board, water absorption decreased with the increase of target density at a given formulation but increased with the increase of wood particle content at a given target density. After 2 and 24 hours immersion, control particleboard was significantly higher in thickness swelling than composite board and its thickness swelling increased with the increase of target density. In composite board, thickness swelling did not vary significantly with the target density at a given formulation but its thickness swelling increased as wood particle content increased at a given target density. Static bending MOR and MOE under dry and wet conditions increased with the increase of target density at a given formulation of wood particle and polypropylene fiber. Especially, the MOR and MOE under wet condition were considerably larger in composite board than in control particleboard. In general, composite board showed superior bending strength properties to control particleboard, And the composite board made from wood particle and polypropylene fiber formulation of 50 : 50 at target density of 0.8 g/$cm^3$ exhibited the greatest bending strength properties. Though problems in uniform mixing and strong binding of wood particle with polypropylene fiber are unavoidable due to their extremely different shape and polarity, wood particle-polypropylene fiber composite boards with higher performance, as a potential substitute for the commercial particleboards, could be made just by controlling processing variables.