• Journal of the Korean institute of surface engineering
• /
• v.38 no.1
• /
• pp.7-13
• /
• 2005

Bismuth thin films were prepared on glass substrate with RF magnetron sputtering and effects of substrate temperature on surface morphology and their electrical transport properties were investigated. Grain growth of bismuth after nucleation and the onset of coalescense of grains at 393 K were observed with field emission secondary electron microscopy. Continuous thin films could not be obtained above 473 K because of grain segregation and island formation. Hall effect measurements showed that substrate heating yields the decrease of carrier density and the increase of mobility. Resistivity of bismuth film has its minimum (about 0.7 x 10/sup -3/ Ωcm) in range of 403～433 K. Annealing of bismuth films deposited at room temperature was carried out in a radiation furnace with flowing hydrogen gas. The change of resistivity was not significant due to cancellation of the decrease of carrier density and the increase of mobility. The abrupt change of electrical properties of film annealed above 523 K was found to be caused by partial oxidation of bismuth layer in x-ray diffraction analysis.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.5
• /
• pp.80-86
• /
• 2012

The disposal of the bottom ash originated from a thermoelectric power plant which used the pulverized coal, has been an important issue of the power plants. In order to find the possible way of recycling of the bottom ash, the applicability of the bottom ash as an inorganic filler for paper making was investigated in this study. The pretreatment with acid were applied for upgrading the properties of bottom ash. The effects of the addition of the bottom ash to the different pulp stocks, Sw-BKP, DIP(Deinked Pulp), Sw-UBKP were evaluated in terms of the change in paper properties. The brightness and tensile strength decreased as the increase of the amount of the bottom ash addition. The bulk and the opacity were increased by the addition of bottom ash. The pretreatment of bottom ash resulted in the increase of improvement of the brightness and the strength properties comparing with those of untreated bottom ash.

• Korean Journal of Materials Research
• /
• v.26 no.1
• /
• pp.35-41
• /
• 2016

The electrical transport properties of $La_{0.5}Sr_{0.5}CrO_3$ below room temperatures were investigated by dielectric, dc resistivity, magnetic properties and thermoelectric power. Below $T_c$, $La_{0.5}Sr_{0.5}CrO_3$ contains a dielectric relaxation process in the tangent loss and electric modulus. The $La_{0.5}Sr_{0.5}CrO_3$ involves the transition from high temperature thermal activated conduction process to low temperature one. The transition temperature corresponds well to the Curie point. The relaxation mechanism has been discussed in the frame of electric modulus spectra. The scaling behavior of the modulus suggests that the relaxation mechanism describes the same mechanism at various temperatures. The low temperature conduction and relaxation takes place in the ferromagnetic phase. The ferromagnetic state in $La_{0.5}Sr_{0.5}CrO_3$ indicates that the electron - magnon interaction occurs, and drives the carriers towards localization in tandem with the electron - lattice interaction even at temperature above the Curie temperature.

• Korean Journal of Materials Research
• /
• v.17 no.3
• /
• pp.132-136
• /
• 2007

Oxidation resistance of sintered ${\beta}-FeSi_{2}$ was investigated at intermediate temperature range in air atmosphere. Fully dense and porous bodies of ${\beta}-FeSi_{2}$ samples were fabricated by using the Spark Plasma Sintering (SPS). They were annealed at $900^{\circ}C$ for 5days to obtain ${\beta}-FeSi_{2}$ phase. The bulk samples were oxidized at $800,\;900\;and\;950^{\circ}C$ in air atmosphere. The high temperature oxidation tests reveal that amorphous $SiO_{2}$ layer, similar to Si was formed and grew parabolically on ${\beta}-FeSi_{2}$. Accelerated oxidation is not observed as well as cracks and grain boundary oxidation. Granular ${\varepsilon}-FeSi$ was developed below the oxide layer as a result of oxidation of ${\beta}-FeSi_{2}$. Oxidation resistance of sintered ${\beta}-FeSi_{2}$ was excellent for high-temperature thermoelectric application.

• Journal of Magnetics
• /
• v.9 no.4
• /
• pp.125-127
• /
• 2004

We have grown Mn-doped $Bi_2Se_3$ and $Sb_2Se_3$ single crystals using the temperature gradient solidification method. We report on the structural and magnetic propertis of Mn-doped $Bi_2Se_3$ and $Sb_2Se_3$ compound semi-conductors. The lattice constants of several percent Mn-doped $Bi_2Se_3$ and $Sb_2Se_3$ were slightly smaller than those of the un-doped samples due to the smaller Mn atomic radius ($1.40 {\AA}$) than those of Bi ($1.60 {\AA}$) and Sb ($1.45 {\AA}$). Mn-doped $Bi_2Se_3$ and $Sb_2Se_3$ showed spin glass and paramagnetic properties, respectively.

• Korean Journal of Metals and Materials
• /
• v.47 no.12
• /
• pp.860-865
• /
• 2009

The effect of Co additive on the electrical properties of Fe-Si alloys prepared by a RF inductive furnace was investigated. The electrical conductivity and Seebeck coefficient were measured as a function of the temperature under an Ar atmosphere to evaluate their applicability to thermoelectric energy conversion. The electrical conductivity of the specimens increased as the temperature increased, showing typical semiconducting behavior. The electrical conductivity of Co-doped specimens was higher than that of undoped specimens and increased slightly as the amount of Co additive increased. This is most likely due to the difference in the carrier concentration and the amount of residual metallic phase ${\varepsilon}$-FeSi (The ${\varepsilon}$-FeSi was detected in spite of an annealing treatment of 100 h at $830^{\circ}C$). Additionally, metallic conduction increased slightly as the amount of Co additive increased. On the other hand, Co-doped specimens showed a lower Seebeck coefficient due to the metallic phase. The power factor of Co-doped specimens was higher than that of undoped specimens. This would be affected more by the electrical conductivity compared to the Seebeck coefficient.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.1
• /
• pp.51-57
• /
• 2013

We have applied mechanical alloying (MA) to produce Heusler $Fe_2VAl$ thermoelectric alloy using a mixture of elemental $Fe_{50}V_{25}Al_{25}$ powders. An optimal milling and heat treatment conditions to obtain the single phase of Fe2VAl compound with fine microstructure were investigated by X-ray diffraction and differential scanning calorimetry (DSC) measurement. The $Fe_{50}V_{25}Al_{25}$ MA sample ball-milled for 60 hours exhibits a bcc ${\alpha}$-(Fe,V,Al) solid solution. Single phase of Heusler $Fe_2VAl$ compound can be obtained by MA of $Fe_{50}V_{25}Al_{25}$ mixture for 60 hours and subsequently heated up to $700^{\circ}C$. Sintering of the MA powders was performed in a spark plasma sintering (SPS) machine using graphite dies at $900{\sim}1000^{\circ}C$ under 60 MPa. The Vickers hardness of bulk sample sintered at $1000^{\circ}C$ was high value of Hv 870. All compact bodies have a high relative density above 90 % with metallic glare on the surface.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.4
• /
• pp.67-74
• /
• 2018

Thermoelectric thin film modules were fabricated by electroplating p-type $Sb_2Te_3$and n-type $Bi_2Te_3$ thin film legs with the same thickness of $20{\mu}m$ and different diameters of $100{\mu}m$, $300{\mu}m$, and $500{\mu}m$, respectively. The output voltage and output power of thin film modules were measured and compared as a function of the leg diameter. The modules processed with thin film legs of $100{\mu}m$, $300{\mu}m$, and $500{\mu}m$-diameter exhibited open circuit voltages of 365 mV at ${\Delta}T=36.7K$, 142 mV at ${\Delta}T=37.5K$, and 53 mV at ${\Delta}T=36.1K$, respectively. Maximum output powers of $845{\mu}W$ at ${\Delta}T=36.7K$, $631{\mu}W$ at ${\Delta}T=37.5K$, and $276{\mu}W$ at ${\Delta}T=36.1K$ were obtained for the modules fabricated with the thin film legs of $100{\mu}m$, $300{\mu}m$, and $500{\mu}m$-diameter, respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.139.2-139.2
• /
• 2016

Electrons and phonons in chalcogenide-based materials play are important factors in the performance of an optical data storage media and thermoelectric devices. However, the fundamental kinetics of carriers in chalcogenide materials remains controversial, and active debate continues over the mechanism responsible for carrier relaxation. In this study, we investigated ultrafast carrier dynamics in an multilayered $\{Sb(3{\AA})/Te(9{\AA})\}n$ thin film during the transition from the amorphous to the crystalline phase using optical pump terahertz probe spectroscopy (OPTP), which permits the relationship between structural phase transition and optical property transitions to be examined. Using THz-TDS, we demonstrated that optical conductance and carrier concentration change as a function of annealing temperature with a contact-free optical technique. Moreover, we observed that the topological surface state (TSS) affects the degree of enhancement of carrier lifetime, which is closely related to the degree of spin-orbit coupling (SOC). The combination of an optical technique and a proposed carrier relaxation mechanism provides a powerful tool for monitoring TSS and SOC. Consequently, the response of the amorphous phase is dominated by an electron-phonon coupling effect, while that of the crystalline structure is controlled by a Dirac surface state and SOC effects. These results are important for understanding the fundamental physics of phase change materials and for optimizing and designing materials with better performance in optoelectronic devices.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.4
• /
• pp.377-385
• /
• 2022

Thermal batteries are specialized as primary reserve batteries that operate when the internal heat source is ignited and the produced heat (450~550℃) melts the initially insulating salt into highly conductive eutectic electrolyte. The heat source is composed of Fe powder and KClO₄ with different mass ratios and is inserted in-between the cells (stacks) to allow homogeneous heat transfer and ensure complete melting of the electrolyte. An ideal heat source has following criteria to satisfy: sufficient mechanical durability for stacking, appropriate heat calories, ease of combustion by an igniter, stable combustion rate, and modest peak temperature. To satisfy the aforementioned requirements, Fe powder must have high surface area and porosity to increase the reaction rate. Herein, the hydrothermal and spray drying synthesis techniques for Fe powder samples are employed to investigate the physicochemical properties of Fe powder samples and their applicability as a heat source constituent. The direct comparison with the state-of-the-art Fe powder is made to confirm the validity of synthesized products. Finally, the actual batteries were made with the synthesized iron powder samples to examine their performances during the battery operation.