• 한국재료학회지
• /
• 제32권6호
• /
• pp.287-292
• /
• 2022

Magnesium-antimonide is a well-known zintl phase thermoelectric material with low band gap energy, earth-abundance and characteristic electron-crystal phonon-glass properties. The nominal composition Mg_3.8-xZn_xSb₂ (0.00 ≤ x ≤ 0.02) was synthesized by controlled melting and subsequent vacuum hot pressing method. To investigate phase development and surface morphology during the process, X-ray diffraction (XRD) and scanning electron microscopy (SEM) were carried out. It should be noted that an additional 16 at. % Mg must be added to the system to compensate for Mg loss during the melting process. This study evaluated the thermoelectric properties of the material in terms of Seebeck coefficient, electrical conductivity and thermal conductivity from the low to high temperature regime. The results demonstrated that substituting Zn at Mg sites increased electrical conductivity without significantly affecting the Seebeck coefficient. The maximal dimensionless figure of merit achieved was 0.30 for x = 0.01 at 855 K which is 30% greater than the intrinsic value. Electronic flow properties were also evaluated and discussed to explain the carrier transport mechanism involved in the thermoelectric properties of this alloy system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 C
• /
• pp.1446-1448
• /
• 1997

TEC(Thermoelectric conversion) is direct conversion method between thermal energy and electric energy. We studied on the mechanical, electrical and thermal properties of thermoelectric module and made experimental thermoelectric generator with BiTe material.

• 한국세라믹학회지
• /
• 제29권11호
• /
• pp.855-862
• /
• 1992

Thermoelectric power, electrical conductivity and Hall effect were measured, as functions of temperature in the range of 100 to 600 K, on polycrystalline Bi4/3Sb2/3Te3 which had been prepared via uniaxial hot-pressing at different temperatures in the range of 373 K to 773 K, aiming at searching a profitable processing route to a polycrystalline thermoelectric material, a promising, viable alternative to a single crystalline one. It was found that, with increasing temperature of pressing under a fixed pressure, the material, normally a p-type prior to being hot-pressed, underwent a transition to n-type. This transition was confirmed to be due to plastic deformation during hot-pressing and interpreted as being attributed to the change of the major ionic defect BiTe' into TeBi˙at temperature high enough for structure elements mobility. Thermoelectric figure-of-merit of the hot-pressed material was discussed in connection with the p-n transition in addition to microstructure.

• 한국전기전자재료학회논문지
• /
• 제35권3호
• /
• pp.203-214
• /
• 2022

Thermoelectric (TE) heating and cooling devices, which are able to directly convert thermal energy into electrical energy and vice versa, are effective and have exhibited a potential for energy harvesting. With the increasing consumer demands for various wearable electronics, organic-based TE composite materials offer a promise for the TE devices applications. Conductive polymers are widely used as flexible TE materials replacing inorganic materials due to their flexibility, low thermal conductivity, mechanical flexibility, ease of processing, and low cost. In this review, we briefly introduce the latest research trends in the flexible TE technology and provide a comprehensive summary of specific conductive polymer-based TE material fabrication technologies. We also summarize the manufacture for high-efficiency TE composites through the complexation of a conductive polymer matrix/inorganic TE filler. We believe that this review will inspire further research to improve the TE performance of conductive polymers.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.454-456
• /
• 2009

N-Type $SbI_3$ doped $95%Bi_2Te_3+5%\;Bi_2Se_3$ compounds were newly fabricated by the combination of gas atomization process and Magnetic Pulsed Compaction process. The thermoelectric properties of the MPCed bulks according to consolidation temperatures were investigated by a combination of microscopy, XRD and thermoelectric property testing. The microstructure of MPCed bulk shows homogeneous and fine distribution through consolidated bulks due to the high solidification of compound powders. The research presented the challenges toward the successful consolidation of thermoelectric powder using magnetic pulsed compaction (MPC) and analysis of thermoelectric properties of the consolidated bulks.

• 한국전기전자재료학회논문지
• /
• 제28권4호
• /
• pp.252-256
• /
• 2015

In this study, we propose a novel fabrication of an oxide-based lateral thermoelectric pn couple and investigate the characteristics of the thermoelectric couple. Electrospun ZnO and $LaSrCoO_3$ nanofibers are used as n- and p-legs of the couple, respectively. The Seebeck coefficients of the n- and p-type nanofibers and the pn couple are $-98.1{\mu}V/K$, $42.4{\mu}V/K$, and $118.8{\mu}V/K$, respectively. The thermoelectric couple generates an output voltage of $484.7{\mu}V$ at a temperature difference of 4.1 K.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.85-86
• /
• 2005

In case of attaching thermoelectric module and heat source, the polymer sheet is attached on the $Al_2O_3$ plate, which is cooling side of thermoelectric module, in order to enhance mechanical safety of the system. It is impossible to calculate the exact distribution of temperature and flow pattern of inner gap of thermoelectric module. Therefore CFD analyses was executed to determine the thermo-fluid phenomena and distribution by Fluent. As the result of these analyses, heat transfer was dominated by conduction and the difference of temperature was linear distribution according to the thickness of polymer sheet.

• 한국전기전자재료학회논문지
• /
• 제28권4호
• /
• pp.257-261
• /
• 2015

In this study, we fabricated a thermoelectric module made of nanoparticles (NPs) and glass fibers investigated its thermoelectric characteristics. P-type HgTe and n-type HgSe NPs synthesized by colloidal method were used as thermoelectric materials and glass fibers were used as spacers between the hot and cold electrodes of the thermoelectric module. In the module, the average Seebeck coefficients of the HgTe and HgSe NPs were 1260 and $-628{\mu}V/K$, respectively. The p-n module generated about a voltage of 11.9 mV and showed a power density of $1.6{\times}10^{-5}{\mu}W/cm^2$ at a temperature difference of 7.5 K.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.142-142
• /
• 2007

Micro thermoelectric generator has been attractive for the alternative power source to operate the wireless sensor node. In this paper, we designed the column-type micro thermoelectric device and their device characteristics were measured. n-type Bi2Te3 and p-type BiSbTe3 thermoelectric thin films were grown on (001) GaAs substrates by metal organic chemical vapour deposition (MOCVD) and they were pattemed. The height of thermoelectric film were controlled by the deposition time, temperature and MO-x gas pressure. Seebeck coefficient was measured at room temperature and hole concentration and electrical resistivity of thermoelectric film were also characterized.

• Journal of the Korean Physical Society
• /
• 제73권11호
• /
• pp.1760-1763
• /
• 2018

To attain power generation with body heat, the thermal resistance matched design of the thermoelectric generator was the principal factor which was not critical in the case of thermoelectric generator for the waste heat generation. The dimension of thermoelectric legs and the number of thermoelectric leg-pairs dependent output power performances of the thermoelectric generator on the human wrist condition was simulated using 1-dimensional approximated heat flow equations with the temperature dependent material coefficients of the constituent materials and the dimension of the substrate. With the optimum thermoelectric generator design, thermoelectric generator modules were fabricated by using newly developed fabrication processes, which is mass production possible. The electrical properties and the output power characteristics of the fabricated thermoelectric modules were characterized by using a home-made test set-up. The output voltage of the designed thermoelectric generator were a few tens of millivolts and its output power was several hundreds of microwatts under the conditions at the human wrist. The measured output voltage and power of the fabricated thermoelectric generator were slightly lower than those of the designed thermoelectric generator due to several reasons.