• Journal of Hydrogen and New Energy
• /
• v.29 no.5
• /
• pp.538-548
• /
• 2018

The thermo-acoustic instability in the combustion process of a gas turbine is caused by the interaction of the heat release mechanism and the pressure perturbation. These acoustic vibrations cause fatigue failure of the combustor and decrease the combustion efficiency. This study is to develop a segmented dynamic thermo-acoustic model to understand combustion instability of gas turbine. Therefore, this study required a dynamic analysis rather than static analysis, and developed a segmented model that can analyze the performance of the system over time using the Matlab/Simulink. The developed model can confirm the thermo-acoustic combustion instability and exhaust gas concentration in the combustion chamber according to the equivalent ratio change, and confirm the thermo-acoustic combustion instability for the inlet temperature and the load changes. As a result, segmented dynamic thermo-acoustic model has been developed to analyze combustion instability under the operating condition.

• Journal of Mechanical Science and Technology
• /
• v.19 no.9
• /
• pp.1811-1820
• /
• 2005

Thermo-acoustic instability of methane/ air flames in an industrial gas-turbine combustor is numerically investigated adopting CFD analysis. The combustor has 37 EV burners through which methane and air are mixed and then injected into the chamber. First, steady fuel! air mixing and flow characteristics established by the burner are investigated by numerical analysis with single burner. And then, based on information on the flow data, the burners are modeled numerically via equivalent swirlers, which facilitates the numerical analysis with the whole combustion system including the chamber and numerous burners. Finally, reactive flow fields within the chamber are investigated numerically by unsteady analysis and thereby, spontaneous instability is simulated. Based on the numerical results, scaling analysis is conducted to find out the instability mechanism in the combustor and the passive control method to suppress the instability is proposed and verified numerically.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.47-50
• /
• 2011

A Rijke tube which has an electric heater and a flow controller was designed and thermo-acoustic instability was induced by the Rijke tube. The thermo-acoustic instability was damped by a resonator and the damping characteristics were investigated and compared to room temperature acoustic test. Results show that decay time of the thermo-acoustic condition was increased by about 40% compared to that of room temperature acoustic test.

• Journal of ILASS-Korea
• /
• v.29 no.1
• /
• pp.23-31
• /
• 2024

This study conducted a 3D thermo-acoustic analysis based on the helmholtz solver to analyze the major resonance modes causing combustion instability in a single-can combustor. The experimental investigations were carried out on a test rig designed by the Korea Institute of Machinery & Materials (KIMM) under various conditions of hydrogen co-firing and fuel staging. Through these experiments, two primary unstable frequencies were identified. To determine the resonance modes of these frequencies, a 3D thermo-acoustic analysis was conducted using temperature information from the test rig. The results confirmed that the unstable frequencies observed in the experiments were all longitudinal modes. Additionally, the mode shapes identified in the analysis facilitated a simplification of the exit geometry for the low-order network model, confirming that this did not significantly affect the fundamental resonance modes.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.873-876
• /
• 2011

In this research, a Helmholtz resonator was applied to the thermo-acoustic environment that has thermal gradient using Rijke tube. The thermo-acoustic instability was invoked by a Rijke tube which use a DC power supplier and a Blower. A target instability frequency was appeared by the Rijke tube. A preliminary experiment on damping characteristics of the resonator in the thermo-acoustic environment was performed and compared with the room temperature experiment data.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.7
• /
• pp.552-558
• /
• 2009

An experimental study using the combustor with branch tube was conducted in order to model the industry combustor with FGR (flue gas recirculation) system and to study a thermo-acoustic instability generated by a branch tube. The branch tube is a structure used to modify a system geometry and then to change its pressure field, and the thermo-acoustic instability, usually occurs in a confined geometry, can result in serious problems on industrial combustors. Thus understanding of the instability created by modifying geometry of combustor is necessary to design and operate combustor with FGR system. Pressure fluctuation in the combustion chamber was observed according to diameter and length of branch and it was compared with the solution of 1-D wave equation. It was found that branch tube affects the pressure field in the combustion chamber, and the pressure fluctuation in the combustion chamber was reduced to almost zero when phase difference between an incipient wave in the combustion chamber and a reflected wave in the branch tube is $\pi$ at the branch point. Also, the reduction of pressure fluctuation is irrespective of the installed height of branch tube if it is below $h^*=0.9$ in the close-open tube and open-open tube.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1166-1171
• /
• 2004

The combustion instability acts as a serious obstacle for the lean premixed combustion of gas turbine and even causes the fatal damage to the combustor and whole system. In this experiment, the pressure fluctuation is highly related to the stabilizing position of flame and fuel injection location. The fuel injection location is connected with the convection time of the fresh mixture, which is important time scale to refresh the mixtures near the flame stabilization location. The flame is extremely unstable when the alternative stabilization occurs and bulk mode frequency (${\sim}10Hz$) of pressure fluctuation is observed in this condition. It was found that the convection time scale of the fresh reactant coincided with the time scale of the bulk mode fluctuation. Hence this phenomenon results from the local equivalence ratio change caused by the pressure fluctuation induced by thermo-acoustic effects.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.83-87
• /
• 2009

Ramjet engine is weak for low frequency combustion instability because of their long air flow passage. A model combustor which has fuel injector and V-gutter shaped flame holder was designed and fabricated in order to simulate a combustion mechanism of ramjet engine, and it could demonstrate combustion instability which might occur in ramjet combustor. The frequency of the instability was very similar to that of acoustic resonance frequency of combustor, and it proved that a typical combustion instability by thermo-acoustic coupling occurred.

• 한국연소학회:학술대회논문집
• /
• 2004.06a
• /
• pp.42-48
• /
• 2004

Lean laminar premixed propane and methane flames which were anchored by a hydrogen-pilot flame in a tube were investigated experimentally. The flame shapes were observed by varying mean velocity from 10cm/s to 140cm/s and equivalence ratio from 0.45 to 0.8. In this study, behaviors of flames are divided into five regions such as tail-out, flash-back, flickering, stable and vibrating flames with respect to the mean velocity and the equivalence ratio. Although the flames are unstable in both the flickering and the vibrating region, they have different characteristics such as the frequency, sound generation and creation process of flame curvature. The flickering region exists near the flammability limit and the flame flickers in a frequency of about 10Hz. When flame front is bended, the propane flame front is straightened and the methane flame front is bended more by thermo-diffusive instability. In the vibrating region, the flame vibrates emitting audible sound in a frequency of about 100Hz. In the boundary of vibrating region, the vibration of flame changes between two modes such as single frequency vibration and dual frequency vibration. Increase and decrease of vibration in each mode are determined by thermo-acoustic instability.

• Journal of Mechanical Science and Technology
• /
• v.20 no.6
• /
• pp.905-913
• /
• 2006

The instability curve of a Rijke tube system was obtained accurately by following different paths of heat power and flow-rate for three regions and by defining its locus from the criterion based on the measured sound pressure levels. The unstable limits in the region of flow-rate lower than that at the minimal power are compared with previous data. To observe the effect of turbulence on the unstable limits, inflow turbulence was introduced by placing a bundle of circular cylinders upstream of the heating part ($50). The large-amplitude inflow fluctuation may delay the transition of the chamber acoustic mode to the unstable Bone even at a sufficient power.