• Fire Science and Engineering
• /
• v.28 no.1
• /
• pp.37-43
• /
• 2014

The high predictive performance of fire detector models is essentially needed to assure the reliability of fire and evacuation modeling in the process of Performance-Based fire safety Design (PBD). The main objective of the present study is to measure input information in order to predictive the accurate activation time of fixed temperature heat detectors adopted in Fire Dynamics Simulator (FDS) as a representative fire model. To end this, Fire Detector Evaluator (FDE) which could be measured the device properties of detector was used, and the spot-type fixed temperature heat detectors of two thermistor types and one bimetal type were considered as research objectors. Activation temperature and Response Time Index (RTI) of detectors required for the fire modeling were measured, and then the RTI was measured for ceiling jet flow and vertical jet flow in consideration of the install location of detectors. The results of fire modeling using measured device properties were compared and validated with the experimental results of full-scale compartment fires. It was confirmed that, in result, the numerically predicted activation time of detector showed reasonable agreement with the measured activation time.

• Korean Journal of Materials Research
• /
• v.8 no.5
• /
• pp.424-428
• /
• 1998

Mn-Ni oxide thin films for NTC thermistor application were deposited on alumina substrates by using rf magnetron sputter. Effects of various substrate temperatures and annealing temperatures on the microstructure. crystal phase, resistivity and B constant were investigated. Microstructure of the films deposited below 178$^{\circ}C$ was fibrous microcrystalline and at 32$0^{\circ}C$and 40$0^{\circ}C$their microstructure was changed to columnar grain structure. After annealing at 90$0^{\circ}C$, the microstructure was transformed to equiaxed grain structure. Most of the phases were mixture of cubic spinel and $Mn_2O_2$ The crystal phase of the film deposited at 40$0^{\circ}C$ was changed to cubic spinel after annealing above 700"c. As the substrate temperature increased, the resistivity and B constant were greatly decreased, and these values become low and stable after annealing between $600^{\circ}C$and $700^{\circ}C$, All thin films deposited in the present study showed NTC thermistor characteristicsstics.

• Journal of the Korean Ceramic Society
• /
• v.46 no.3
• /
• pp.330-335
• /
• 2009

We investigated the effects of the re-oxidation temperature and time on the positive temperature coefficient (PTC) of resistivity characteristics of Sm-doped $BaTiO_3$ sintered at $1200{\sim}1260^{\circ}C$ for 2 h in a reducing atmosphere (3% $H_2/N_2$), followed by re-oxidization processes in air, in which re-oxidization temperature and time were $600{\sim}1000^{\circ}C$ and $1{\sim}10$h, respectively. The result reveals that Smdoped (Ba,Ca)$TiO_3$ ceramics fired in a reducing atmosphere exhibit low PTC characteristics, whereas the sample re-oxidized at $800^{\circ}C$ for 1 h in air exhibit pronounced PTC characteristics. The room-temperature resistivity and jumping characteristics of resistivity (${\rho}_{max}/{\rho}25^{\circ}C$) decrease with Sm contents. The PTC characteristics with reoxidization time at $800^{\circ}C$ have improved about $2{\sim}3$ orders of magnitude whereas differed according to the sintering temperature. The 0.7 at% Sm-doped (Ba,Ca)$TiO_3$ samples reveal the best PTC characteristics in the present range of formula and processes.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2206-2208
• /
• 2003

This paper is performed to find the effects on body heat by stimulating the skin with the heat of a moxibustion cauterizer and the Artemisia-lotion which cause the extension of the blood vessel. The Artemisia-lotion is made by extracting the vasodilator and antioxidant compounds from the $Artemisia-CH_2Cl_2$ fraction. The moxibustion cauterizer is constructed with a DC power supply and 3 heating electrodes with PTC(Positive Temperature Coefficients) thermistor. The stimulation temperature level of the moxibustion cauterizer is $45^{\circ}C\;-48^{\circ}C$. We gave the subjects the following stimulating conditions; only heat stimulation, only Artemisia -lotion stimulation, and both stimulations. The measurement of body heat was performed with a infrared thermography system . Finally we could estimate the effects of a betterment of circulation of the blood from $Artemisia-CH_2Cl_2$ fraction.

• Proceedings of the KIEE Conference
• /
• 1991.11a
• /
• pp.278-281
• /
• 1991

1) The specimen with 0.175[mol%] of additive $Sb_2O_3$ was minute and didn't appear porosity. The relation between the ratio of resistivity at $160^{\circ}C$ to that at $121^{\circ}C$ of the specimen with 0.175[mol%] of additive $Sb_2O_3$ was $3{\times}10^4$ and it's great value from among specimens. 2) The curie temperature of the specimen with 0.2 [mol%] of additive $Sb_2O_3$ was $140^{\circ}C$ AND it's great value from among specimens and those of other were $121^{\circ}C$ in all therefore, the specimen with above 0.2[mol%] of additive $Sb_2O_3$ is not match for PTCR 3) The variation of radiation properties of the specimen with 0.2[mol%] of additive $Sb_2O_3$ was very steep in the range of far-infrared $5{\sim}10[{\mu}m]$ but radiation percentage was very high of 0.92 in the range of $10[{\mu}m]$.

• Journal of the Korean Geophysical Society
• /
• v.4 no.4
• /
• pp.257-266
• /
• 2001

The properties of electrical resistance of Mn-Co-Ni-Fe oxide-based therrnistor with various Fe contents in sintering process at 1200 to 1400℃ for 4 hours in air atmosphere for fabricating therrnistor materials were investigated. The results were as follows: all samples showed single cubic spinel crystal structures in all region. The electrical conductivinity is the highlest thermistor sintered at 1300℃ for 4 hours. In general when the Fe content is increased except F-2, the resistivity increases and relatively the conductivity decreases. Particularly F-2 composition exhibited the highlest electrical conductivity(1.4x $10^-3$$Ω$cm) and relatively low B constant(2906K)

• Proceedings of the KSRS Conference
• /
• v.1
• /
• pp.364-367
• /
• 2006

Nonlinear internal waves (NLIWs) are usually generated by nonlinear process on linear internal waves (IW). Near HengChun Ridge that links Taiwan and Luzon Islands, we found that there are linear internal waves following NLIW and they travel westward at different speed, about 1.5 m/s for IW and 2.9 m/s for NLIW. This phenomenon was observed on site with ship radar and echo sounders, and later verified with thermistor chain. West of Luzon Strait, the separation of NLIW are 5 km or more, while linear internal waves are lines of wave crests at nearly equal distance that is only a few hundred meters apart. The current hypothesis is that most of the energy of internal tide forms a beam that propagates upward from the eastern shoulder of ocean ridge and later interacts with sea surface and thermocline. The interaction with thermocline generates linear internal wave that propagate along the pycnocline at about 1.5 m/s. The interaction with sea surface scatters internal wave energy downward, ensonifies the water column and generates large nonlinear waves that propagate westward at 2.9 m/s as mode 1 in a waveguide.

• Journal of the Korean Ceramic Society
• /
• v.33 no.12
• /
• pp.1301-1310
• /
• 1996

Generally it requires high sintering temperatures more than 135$0^{\circ}C$ to make semiconductive BaTiO3 ceramics. Also it is very difficult to achieve a homogeneous mixing in solid-state reaction method. Therefore the liquid phase distributed to non-uniform dilute the characteristics of PTCR. In order to improve the uniformity this study is used the sol-gel coating method. Using this method we studied the new manufacturing process that had a high reproducibility and mass production capability. Tetraethyl orthosilicate (TEOS) was used as a source of Si. The semiconductive BaTiO3 ceramics which was produced by sol-gel method for the SiO2 addition and sintered between 124$0^{\circ}C$ and 130$0^{\circ}C$ showed almost same resistivity at room temperature among 125$0^{\circ}C$ and 130$0^{\circ}C$. As the results We could be sintered the semiconducting BaTiO3 ceramics at lower temperature even at 125$0^{\circ}C$ maintaining the same specific resistivity ratio ($\rho$max/$\rho$min) at 130$0^{\circ}C$. The specific resistivity both below and above the Curie temperature were increased by slow cooling and the steepness of the plots in the reasion of transition from low to high resistance increased as the cooling rate decreased.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1993.05a
• /
• pp.3-5
• /
• 1993

It is very important that a spectrum of reflectance is in accord wi th a spectrum of absorbance for a effective heating. Therefore. the objective of this study was to achieve a technical composite for material plan which PTC thermistor increase a radiation property of far-infrared and keep a characteristic of R-T The Ceramic speciman studies had the composition $BaTiO_3$ with additive of 1.67 $Al_2O_3$, 3.75 $SiO_2$, 1.25 $TiO_2$, 0.15 $Sb_2O_3$ and 0.00-0.182 $MnO_2$. $MnO_2$ amounts of additives was both increase on the anomalous resistivity-temperature characteristics and high efficiency on the radiation properties bodies of far-infrared. This result shows that specimens produced high emissivity(average 0.8) of far-infrared at 4.5-15$[{\mu}m]$ by measuring a characteristic of IR and R-T.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.180-181
• /
• 2008

화학양론적 $BaTiO_3$의 소결은 고온의 에너지를 필요로 하며, 내부전극과 세라믹충의 동시소성과정에서 Ni이 세라믹층으로의 확산이 발생되어 PTC의 물성저하를 초래한다. 본 연구에서는 저온에서 액상을 형성하여 소결온도를 낮추는 것으로 알려진 산화물 및 비산화물계 소결첨가제가 적층 PTC 세라믹스의 미세구조 및 전기적 특성에 미치는 영향에 대하여 고찰하였다. 소결과정에서 분해되어 기체를 형성하는 BN, $Li_2CO_3$, LiF의 경우 기공율을 증가시켜 산소의 이동경로를 형성하였으며, 이는 입계의 재산화를 용이하게 하여 PTC 효과를 보였다.