• 한국가스학회지
• /
• 제17권1호
• /
• pp.1-6
• /
• 2013

$NO_x$ 배출허용기준이 강화되는 배출가스 규제에 대응하기 위한 대안으로서 제시되는 천연가스-수소 혼합연료 (HCNG)는 수소의 빠른 화염속도와 넓은 가연범위를 이용하여 후처리 장치 없이 규제치를 만족할 수 있어 디젤엔진에 비해 저공해성이나 가격경쟁력 측면에서 유리한 장점이 있다. 열효율 측면에서도 우수성을 인정받는 HCNG 연료는 수소 혼합율은 물론 운전영역별 운전전략에 따라 연소특성이 달라진다. 본 연구에서는 대형 천연가스 엔진에 수소혼합율 30%의 HCNG 연료를 적용하여 운전영역별 안정적인 연소특성 및 배출가스 특성을 살펴봄으로써 상용화 가능성과 운전전략을 포함한 기술 개발방향에 대해 검토하고자 하였다.

• Journal of Electrical Engineering and Technology
• /
• 제10권6호
• /
• pp.2256-2261
• /
• 2015

In the power plant using high temperature fuel cells such as Molten Carbonate Fuel Cell(MCFC), and Solid Oxide Fuel Cell(SOFC), the generated electric power per area of power generation facilities is much higher than any other renewable energy sources. - High temperature fuel cell systems are capable of operating at MW rated power output. - It also has a feature that is short for length of the line for connecting the interior of the generation facilities. In normal condition, these points are advantages for voltage drops or power losses. However, in abnormal condition such as fault occurrence in electrical system, the fault currents are increased, because of the small impedance of the short length of power cable. Commonly, to minimize the thermal-mechanical stresses on the stack and increase the systems reliability, we divided the power plant configuration to several banks for parallel operation. However, when a fault occurs in the parallel operation system of power main transformer, the fault currents might exceed the interruption capacity of protective devices. In fact, although the internal voltage level of the fuel cell power plant is the voltage level of distribution systems, we should install the circuit breakers for transmission systems due to fault current. To resolve these problems, the SFCL has been studied as one of the noticeable devices. Therefore, we analyzed the effect of application of the SFCL on bus tie in a fuel cell power plants system using PSCAD/EMTDC.

• 대한기계학회논문집A
• /
• 제40권2호
• /
• pp.207-212
• /
• 2016

신뢰성 및 반복성을 포함한 장점을 갖고 있는 고주파 유도 경화는 많은 산업분야에 사용된다. 고주파 유도 경화는 화염을 이용하지 않고 최소한의 시간에 에너지-효율적인 가열방법을 제공하는 비접촉식 방법이다. 최근, 유한요소법을 이용한 고주파 유도 경화가 적극적으로 연구되고 있지만, 이들 연구는 단지 분석의 정확도에 초점을 맞추고 있다. 본 논문에서는 코일 및 입력 전원을 동일한 형태의 조건에서 가변 주파수를 적용하여 해석하고 실험결과와 비교하였다. 해석과 실험 결과는 최적의 주파수인 3kHz를 사용하였을 때 경화 깊이가 거의 동일함을 보인다.

• International Journal of Automotive Technology
• /
• 제8권6호
• /
• pp.687-696
• /
• 2007

To increase the reliability of auto-ignition in CAI engines, the thermodynamic properties of intake flow is often controlled using recycled exhaust gases, called internal EGR. Because of the internal EGR influence on the overall thermodynamic properties and mixing quality of the gases that affect the subsequent combustion behavior, optimizing the intake and exhaust valve timing for the EGR is important to achieve the reliable auto-ignition and high thermal efficiency. In the present study, fully 3D numerical simulations were carried out to predict the mixing characteristics and flow field inside the cylinder as a function of valve timing. The 3D unsteady Eulerian-Lagrangian two-phase model was used to account for the interaction between the intake air and remaining internal EGR during the under-lap operation while varying three major parameters: the intake valve(IV) and exhaust valve(EV) timings and intake valve lift(IVL). Computational results showed that the largest EVC retardation, as in A6, yielded the optimal mixing of both EGR and fuel. The IV timing had little effect on the mixing quality. However, the IV timing variation caused backflow from the cylinder to the intake port. With respect to reduction of heat loss due to backflow, the case in B6 was considered to present the optimal operating condition. With the variation of the intake valve lift, the A1 case yielded the minimum amount of backflow. The best mixing was delivered when the lift height was at a minimum of 2 mm.

• 한국산학기술학회논문지
• /
• 제13권3호
• /
• pp.961-966
• /
• 2012

고유가 시대를 맞아 에너지 절약이 사회적으로 이슈화됨에 따라 진공유리에 대한 관심이 높아지고 있다. 진공유리 개발을 위한 핵심 공정 중 유리모서리 접합공정은 두 장의 유리 사이를 진공으로 유지하기 위해 높은 신뢰도를 요한다. 본 논문에서는 유리 모서리 접합 시 기존 프릿을 이용하여 접합하는 방법과 달리 고밀도열원인 수소혼합가스를 이용하여 모서리를 접합하는 공정을 제시하였다. 또한 유리의 파손 및 변형방지를 위해 전기로내의 분위기 온도를 설정하고 균일도를 측정하였다. 기초시험을 통해 모서리접합 공정변수를 설정하고 공정변수에 따른 유리 모서리 접합부 면적과의 수학적관계식을 다중회귀분석으로 도출하였다.

• 한국추진공학회지
• /
• 제19권4호
• /
• pp.24-36
• /
• 2015

본 연구에서는 복사 데이터베이스 기반의 LBL 모델과 근사 이론에 기초한 입자의 영향이 고려된 로켓 플룸의 적외선 스펙트럼 예측을 수행하였다. 로켓 플룸 내에 존재하는 가스 분자의 스펙트럼을 예측하기 위하여 고해상도 복사 데이터베이스를 이용하였다. 로켓 플룸 내에 존재하는 입자는 수트 입자로 모델링 하였으며 미 이론의 1항 근사 및 레일리 근사를 적용하였다. 두 이론의 적용에 대한 타당성을 검증하였으며, 이를 바탕으로 로켓 플룸의 적외선 스펙트럼을 예측하였다. 수트 입자의 영향을 고려함으로써 짧은 파장 영역 대에서 향상된 로켓 플룸의 스펙트럼 예측 결과가 도출되었다.

• International Journal of Safety
• /
• 제11권2호
• /
• pp.15-21
• /
• 2012

This paper is aimed to develop an electrical fire detection system (EFDS) which can analyze the possibility of electrical fire for overcurrent, leakage current and arc signals of panel board in traditional market shop. The EFDS adopted fuzzy logic and precursory data for overcurrent, leakage current and arc signals to evaluate the possibility of electrical fire. The signals are obtained directly from panel board in traditional market shops and fuzzy membership function is obtained from experiment, simulation, expert's advice. The overcurrent data is acquired by thermal data of normal and abnormal states (partial disconnection) on the insulated electrical wire, in accordance with the increase of the current signal, The leakage current data is obtained under various environments. The arc signal is acquisited by waveforms of instantaneous value in time domain and frequency band in frequency domain. The Fuzzy algorithm for DB of EFDS consists of fuzzification, inference engine by Mamdani's method and defuzzification by center of gravity method. In order to verify the performance and reliability of EFDS, it was applied to Jeon-Ju traditional market shops (90 shops) in Korea. Results show that EFDS in this paper is useful in alarming the fire case, which will prevent severe damage to human beings and properties, and reduce the electrical fires in a vulnerable area of electrical disaster.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제28권1호
• /
• pp.53-60
• /
• 2002

Neurosensory dysfunction of the injured inferior alveolarnerve(IAN) is a common and distrssing consequence of traumatic or iatrogenic injury. Conventional neurosensory testing has been used to detect and monitor sensory impairments of the injured IAN. However, these tests had low reliability and are not qualitative at best because they are based on solely on the patient's subjective assesment of symptoms. Consequently, there is need for more reliable, sensitive, and objective test measures to document and to monitor sensory dysfunction of the trigeminal nerve. This study was to investigate DITI's (digital infrared thermographic imaging) potential as a diagnostic alternative for evaluating of the nerve injures and sensory disturbance. Subjects were 30 patients who had been referred to Ewha Medical Center due to sensory disturbance of the lower lip and chin followed after unobserved inferior alveolar nerve injuries. The patients were examined by clinical neurosensory tests as SLTD (static light touch discrimination), MDD (moving direction discrimination), PPN (pin prick nociception) and DITI (digital infrared thermographic imaging). The correlation between clinical sensory dysfunction scores(Sum of SLTD, MDD, PPN, NP, Tinel sign) and DITI were tested by Spearman nonparametric rank correlation anaylsis & Kruskal-Wallis test, Wilcoxon 2-sample test. This study resulted in as follows; (1) The difference of thermal difference between normal side and affected side was as ${\Delta}-3.2{\pm}0.13$. (2) The DITI differences of the subjects presenting dysesthesia of the lip and chin were correlated significantly with the neurosensory dysfunction scores(r=0.419, p=0.021)and SLTD (r=0.429, p<0.05). (3) The MDD, PPN, NP, Tinel sign, duration, gender were not correlated with DITI(p> 0.05). Therefore, the DITI(digital infrared thermographic imaging) can be an option of the useful objective diagnostic methods to evaluate the injured inferior alveolar nerve and sensory dysfunction of trigerminal nerve.

• 마이크로전자및패키징학회지
• /
• 제12권1호
• /
• pp.65-71
• /
• 2005

At present, Electronic industries push ahead to eliminate the Pb(Lead) -a hazardous material-from all products. Especially, we have performed to select the optimum standard composition of lead free alloy for the application to products for about 3 years from 2000. These days, we have the chance for applying to the mass-production. This project constructed the system for applying the lead free solders on consumer electronic products, which is one of the major products of the LG Electronics. To select the lead free solders with corresponding to the product features, we have passed through the test and applied with Sn-3.0Ag-0.5Cu alloy system to our products, and for the application to the high melting temperature composition, we secured the thermal resistance of the many parts and substrate and optimized the processing conditions. We have operated the temperature cycling test and the high temperature storage test under the standards to confirm the reliability of the products. On these samples, we considered the consequence of our decision by the operating test. For the long life time of the product, we have operated the temperature cycling test at $-45^{\circ}C\;-\;+125^{\circ}C$, 1 cycle/hour, 1000 cycles. Also we have tested the tin whisker growth about lead free plating on lead finish. We have analyzed with the SEM, EDS and any other equipment for confirming the failure mode at the joint and the tin whisker growth on lead free finish.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.150-150
• /
• 2010

Carbon nanotubes have drawn attention as one of the most promising emitter materials ever known not only due to their nanometer-scale radius of curvature at tip and extremely high aspect ratios but also due to their strong mechanical strength, excellent thermal conductivity, good chemical stability, etc. Some applications of CNTs as emitters, such as X-ray tubes and microwave amplifiers, require high current emission over a small emitter area. The field emission for high current density often damages CNT emitters by Joule heating, field evaporation, or electrostatic interaction. In order to endure the high current density emission, CNT emitters should be optimally fabricated in terms of material properties and morphological aspects: highly crystalline CNT materials, low gas emission during electron emission in vacuum, optimal emitter distribution density, optimal aspect ratio of emitters, uniform emitter height, strong emitter adhesion onto a substrate, etc. We attempted a novel approach to fabricate CNT emitters to meet some of requirements described above, including highly crystalline CNT materials, low gas emission, and strong emitter adhesion. In this study, CNT emitters were fabricated by filtrating an aqueous suspension of highly crystalline thin multiwalled CNTs (Hanwha Nanotech Inc.) through a metal mesh. The metal mesh served as a support and fixture frame of CNT emitters. When 5 ml of the CNT suspension was engaged in filtration through a 400 mesh, the CNT layers were formed to be as thick as the mesh at the mesh openings. The CNT emitter sample of $1{\times}1\;cm^2$ in size was characteristic of the turn-on electrical field of 2.7 V/${\mu}m$ and the current density of 14.5 mA at 5.8 V/${\mu}m$ without noticeable deterioration of emitters. This study seems to provide a novel fabrication route to simply produce small-size CNT emitters for high current emission with reliability.