• Environmental Engineering Research
• /
• v.24 no.4
• /
• pp.529-542
• /
• 2019

Nowadays, drying methods for municipal solid waste quality improvement have been adopted in the developed and developing countries to valorize wastes for a renewable energy source, reduce dependency on fossil fuel and keep safer disposal at landfills. Among them, biodrying, biostabilization, thermal drying and solar drying are the most common. Drying of municipal solid waste could offer several environmental and economic benefits. Therefore, this review highlighted the drying methods for municipal solid waste quality improvement around the world and compared them based on the reduction of moisture, weight and volume of municipal solid wastes against drying temperature and time by using statistical analysis. It was observed that the drying temperature of different drying methods accounted for 115 ± 40℃ for thermal drying, 59 ± 37℃ for solar drying, 55 ± 15℃ for biodrying and 58 ± 11℃ for biostabilization. Among the drying methods, thermal drying provided the shortest drying time. The moisture reduction, weight reduction, volume reduction and heating value increase of municipal solid waste could vary with drying temperature and time. Finally, the benefits and drawbacks of different drying methods were specified, and recommendations were made for the future efficient drying.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.13 no.2
• /
• pp.74-84
• /
• 2005

The objectives of this study was to investigate the improvement of thermal kinetics for disposal of sewage sludge using thermal wind drying. The operational parameters varied are the temperature of $130{\sim}170^{\circ}C$ and evaporation velocity WD. Important parameters effect on thermal kinetics for evaporation of water in sewage sludge studied include the drying time, water content of sewage sludge, solids amount of sewage sludge(TS%) by the varied temperature. The saturation point of water evaporation was observed at the drying time of 60 min in conditions of drying temperature $170^{\circ}C$ and drying time of 120 min by drying temperature $130^{\circ}C$ and WD=0.95 m/s. Operation at drying temperature of $170^{\circ}C$ led to higher rate of evaporation than those 130, $150^{\circ}C$ at WD=1.0 m/s and WD=1.0 m/s was higher than WD=0.5 m/s at drying temperature of $130^{\circ}C$.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.2
• /
• pp.23-28
• /
• 2007

Wood fuel must be dried before combustion to minimize the energy loss. Sawdust of Japanese red pine was dried in a direct contact thermal screw dryer to investigate the drying characteristics of sawdust as a raw material for bio-fuel. Average drying rate and energy efficiency was 1.4%/min and 69.23% at $100^{\circ}C$, respectively, and those at $120^{\circ}C$ was 2.1%/min and 71.03%, respectively.

• Journal of Power System Engineering
• /
• v.5 no.1
• /
• pp.44-49
• /
• 2001

Low temperature vacuum drying technique shows very excellent energy efficiency and prominent drying performances compared with the conventional hot air drying technique. This study was focused on the thermal characteristics of the low temperature vacuum drying technique. From the results of this study, it was confirmed that the time consumption for drying with the new drying technique could be shortened to about 1/3 of the time consumption with the conventional hot air drying technique under the same drying conditions for wet products. Also, the maximum drying rate with the new drying technique reached to about $0.35kg/m^2h$ at about 400% of moisture content.

• Journal of the Korean Wood Science and Technology
• /
• v.26 no.4
• /
• pp.34-42
• /
• 1998

Three hardwood (ash, alder and black locust) and three softwood (Japanese red pine, radiata pine and Western hemlock) specimens were dried in microwave(MlW) oven and their drying rates were obtained. Their specific permeabilities were also measured by using a modified liquid permeability measuring device. The correlation between the M/W drying rates and permeabilities of six species were statistically analyzed. It was revealed that within a species there is a logarithmic relationship between the M/W drying rates and average moisture contents and that among species there is a linear relationship between the M/W maximum drying rates and the average specific permeabilities. A exception was Western hemlock, which was of low permeability and of high drying rate. A Me-time equation, which showed a good agreement with the actual data, was derived. Thus using this equation the moisture contents of wood and the drying end points of M/W drying could be predicted. Infrared images of the thermal distribution in wood were illustrated.

• Proceedings of the KIPE Conference
• /
• 2010.07a
• /
• pp.589-590
• /
• 2010

The drying method that is applied in industry is mainly used hot air drying method witch is circulated heated air by generating heat from thermal source. But these methods have problems such as decreasing drying efficiency and waste of energy by low thermal efficiency. Therefore, this paper proposes high efficiency hybrid drying system using near infrared ray(NIR) drying method using halogen lamp and hot air drying method. And this paper proves validity of proposed drying system through experiment about thermal and humidity of drying system inside.

• Solar Energy
• /
• v.9 no.2
• /
• pp.14-21
• /
• 1989

The heat transfer analysis is performed on unloaded solar utilization dryer, and thermal performance for a prototype model while drying red-pepper is also investigated. Results of theoretically derived thermal equations are in good agreement with experimental data. This constructed feature of the prototype demonstrates the excellent technical drying performance. Finally, this paper recommends the further work to develop advanced and economic solar utilization multi-purpose dryer.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.22 no.12
• /
• pp.828-836
• /
• 2010

The drying is a process that involves coupled and simultaneous heat and mass transfer. When a wet solid is subjected to thermal drying, two processes occur simultaneously. Drying is classified according to heat transfer characteristics in terms of conduction, convection and radiation. In thermal drying, radiation is easier to control than conduction and convection drying and involves a relatively simple structure. In this study, we measured energy consumption, surface hardness of paint and surface gloss with variation of surface temperature of drying materials and drying time. Drying characteristics and energy consumption between heating panels and hot air heating have been presented. The present study shows that a dryer using heating panels is more effective than a hot air dryer from the viewpoint of energy conservation. The hot air dryer, however, was not optimized and more studies on various parameters related to drying will need to be investigated for definite comparison of drying characteristics of the dryers. The result, even if limited, would present the effective availability of paint drying.

• Journal of Welding and Joining
• /
• v.14 no.6
• /
• pp.101-108
• /
• 1996

In this study, WC-l7wt% Co composite powder for thermal spray was fabricated by spray drying method. The agglomerated composite powder had spheroidal morphology and the particle size distribution was 20~60${\mu}{\textrm}{m}$. WC and Co were distributed homogeneously. However, the strength of the spray-dried agglomerate was low due to the pores within the agglomerate. Therefore, the spray-dried agglomerate was broken down during HVOF thermal spray and the microstructure was inhomogeneous with many pores within the coating layer. And the decomposition of WC to W and $W_{6}$ $C_{2.54}$ was accelerated. The strength and flowability of the agglomerate were greatly improved by sintering heat treatment(110$0^{\circ}C$, 1 hour, hi atmosphere), and then the coating layer showed dense and homogeneous microstructure with well-developed splats. The hardness of the coating layer was H $v_{300}$ = 1072.2.2.

• Solar Energy
• /
• v.11 no.3
• /
• pp.9-20
• /
• 1991

Experiments for drying radish were carried out to analyze the drying characteristics and quality evaluation between solar heated-air drying and natural air drying system. Solar heated-air drying system consists of a small fan, a solar air heater and a tunnel dryer. Simulation model for thermal environments of solar collector was developed to investigate the effect of solar radiation and airflow rate on thermal performance.