• Korean Chemical Engineering Research
• /
• 제55권3호
• /
• pp.322-331
• /
• 2017

지역난방은 국내에 1985년 처음 도입되었다. 지하 열배관망의 사용연한이 30년 이상 증가함에 따라, 지하에 매설된 열수송 배관 특성상 유지관리가 중요한 문제로 대두되고 있다. 노후화가 진행된 열배관망 유지보수를 위한 정기적인 점검, 운영관리 시 다양한 복합 기술이 필요하다. 특히 현장에서 경제적 관점에서 최적 유지보수 및 교체시점을 도출하기 위하여 의사결정에 활용될 수 있는 모형개발이 요구되고 있다. 본 연구에서는 한국지역난방공사 수도권 5개 지사열 배관망 운영 시 보수이력과 사고성 데이터를 바탕으로 분석하였다. 정성적 분석과 이항 로지스틱 회귀분석의 통계적 기법을 도입하여 파손확률 모델을 개발하였다. 보수이력 및 사고성 자료의 정성적 분석 결과, 파이프라인 손상의 가장 중요한 원인으로 건설 시공불량, 배관의 부식과 자재 불량이 전체의 약 82%를 차지했다. 통계 모델 분석에서는 분류의 분리 점을 0.25로 설정함으로써 열배관 파손 및 비 파손 분류의 정확도가 73.5%로 향상 되었다. 파손확률 모델 수립을 위해 Hosmer와 Lemeshow 검정과 독립변수의 유의성 검정, 모델의 Chi-Square 검정을 통해 모델의 적합성을 검증 하였다. 열배관망 파손의 위험순위 분석결과에 따르면 파손확률을 가장 높이는 경우는 겨울철 서울지역 자동차 도로에 있는 10년 이상 된 250mm이하 배관 Reducer에서 F 건설회사가 시공했던 열배관망으로 분석되었다. 본 연구결과는 열배관망 시스템의 유지관리 및 예방점검, 교체 사업 우선순위를 정할 때 활용 가능하다. 또한 이를 통하여 점검 유지보수 등 사전에 사고예방 계획을 수립하여 대처함으로써 열배관 파손의 빈도를 감소시키고 보다 적극적인 열배관망 관리에 이용할 수 있을 것으로 사료된다.

• 설비공학논문집
• /
• 제27권1호
• /
• pp.1-7
• /
• 2015

A boiling heat transfer system is used in a variety of industrial processes and applications, such as refrigeration, power generation, heat exchangers, cooling of high-power electronics components, and cooling of nuclear reactors. The critical heat flux (CHF) is the thermal limit during a boiling heat transfer phase change; at the CHF point, the heat transfer is maximized, followed by a drastic degradation beyond the CHF point. Therefore, Enhancement of CHF is essential for economy and safety of heat transfer system. In this study, the CHF and heat transfer coefficient under the pool-boiling state were tested using multi-wall carbon nanotubes (MWCNTs) CM-95 and CM-100. These two types of multi-wall carbon nanotubes have different sizes but the same thermal conductivity. The results showed that the highest CHF increased for both MWCNTs CM-95 and CM-100 at the volume fraction of 0.001%, and that the CHF-increase ratio for MWCNT CM-100 nanofluid with long particles was higher than that for MWCNT CM-95 nanofluid with short particles. Also, at the volume fraction of 0.001%, the MWCNT CM-100 nanofluid indicated a 5.5% higher CHF-increase ratio as well as an approximately 23.87% higher heat-transfer coefficient increase ratio compared with the MWCNT CM-95 nanofluid.

• 한국자동차공학회논문집
• /
• 제21권6호
• /
• pp.1-7
• /
• 2013

This paper focuses on cooling fan control by using a magnetic clutch type for the improvement of fuel economy on a heavy city bus. In general, Heavy duty vehicles use viscous clutch type cooling fan which has some disadvantages, such as slow response, wide temperature variation of engine coolant water. But a magnetic clutch type cooling fan can be controlled electronically so the engine coolant temperature can be precisely controllable and this effects could be used to reduce fuel consumption. A control system for applying the magnetic clutch type cooling fan was developed in this study and applied to the real field test and chassis dynamometer test. The result showed well controlled coolant temperature and enhancement of fuel economy.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2001년도 유체기계 연구개발 발표회 논문집
• /
• pp.11-16
• /
• 2001

It is not easy to apply a small-sized centrifugal fan to the duct used for the thermal management of home electronic appliances due to complex design parameters of its blades and scroll. The main objective of this study was to develop the systematic process to design an optimal centrifugal fan based on the 3-dimensional configuration of blades obtained from the conceptual design program self-developed with the given design constraints such as the flow rate, the total pressure loss, the size of fan, and the number of rotation. The design process to find an optimal centrifugal fan for refrigerator was technologically linked in many ways. The complex grid generation system of the fan model included scroll was adopted for the numerical simulation. The FVM CFD code, FLUENT, was used to investigate the three dimensional flow pattern at the coordinate system of rotating frame and to check the optimal performance of the fan. By using this design process, a selected centrifugal fan was designed, numerically simulated, manufactured and experimentally tested in the wind tunnel. The performance curve of fan manufactured by NC process was compared with numerically obtained characteristic curve. The developed design method was proved into being excellent because these two curves were well matched.

• 설비공학논문집
• /
• 제26권7호
• /
• pp.308-314
• /
• 2014

A heat pump has been considered as a thermal management unit for electric vehicles, including the heating and cooling of the cabin. However, the heat pump shows performance degradation at low outdoor temperatures or high compressor speeds. In this study, a R-134a heat pump for an electric vehicle was designed to improve system efficiency, by applying vapor injection with an internal heat exchanger. The heating performance characteristics of the vapor injection heat pump were analyzed at various compressor speeds and outdoor temperatures. The vapor injection heat pump showed 13.3% COP improvement over the non-injection heat pump, when the heating capacity was fixed at 5.2 kW. In addition, the heating capacity of the vapor injection system increased by 9.6%, as compared to the non-injection system.

• Journal of Computing Science and Engineering
• /
• 제4권3호
• /
• pp.189-206
• /
• 2010

It is generally accepted that dynamic voltage scaling (DVS) is one of the most effective techniques of energy minimization for real-time applications in embedded system design. The effectiveness comes from the fact that the amount of energy consumption is quadractically proportional to the voltage applied to the processor. The penalty is the execution delay, which is linearly and inversely proportional to the voltage. According to the granularity of tasks to which voltage scaling is applied, the DVS problem is divided into two subproblems: inter-task DVS problem, in which the determination of the voltage is carried out on a task-by-task basis and the voltage assigned to the task is unchanged during the whole execution of the task, and intra-task DVS problem, in which the operating voltage of a task is dynamically adjusted according to the execution behavior to reflect the changes of the required number of cycles to finish the task before the deadline. Frequent voltage transitions may cause an adverse effect on energy minimization due to the increase of the overhead of transition time and energy. In addition, DVS needs to be carefully applied so that the dynamically varying chip temperature should not exceed a certain threshold because a drastic increase of chip temperature is highly likely to cause system function failure. This paper reviews representative works on the theoretical solutions to DVS problems regarding inter-task DVS, intra-task DVS, voltage transition, and thermal-aware DVS.

• Nuclear Engineering and Technology
• /
• 제42권5호
• /
• pp.590-599
• /
• 2010

Recently, efficient operation and practical management of power plants have become important issues in the nuclear industry. In particular, typical aging parameters such as stress and cumulative usage factor should be determined accurately for continued operation of a nuclear power plant beyond design life. However, most of the major components have been designed via conservative codes based on a 2-D concept, which do not take into account exact boundary conditions and asymmetric geometries. The present paper aims to suggest an effective fatigue evaluation methodology that uses a prototype of the integrated model and its transfer functions. The validity of the integrated 3-D Finite Element (FE) model was proven by comparing the analysis results of individual FE models. Also, mechanical and thermal transfer functions, known as Green's functions, were developed for the integrated model with the standard step input. Finally, the stresses estimated from the transfer functions were compared with those obtained from detailed 3-D FE analyses results at critical locations of the major components. The usefulness of the proposed fatigue evaluation methodology can be maximized by combining it with an on-line monitoring system, and this combination, will enhance the continued operations of old nuclear power plants.

• 한국수소및신에너지학회논문집
• /
• 제16권4호
• /
• pp.364-371
• /
• 2005

Fuel cell systems(FCS) have a financial and environmental advantage by providing electricity at a high efficiency and useful heat. For use in a residence, a polymer electrolyte fuel cell system(PEFCS) with a battery pack and a hot water storage tank has been modelled and simulated. The system is operated without connection to grid line. Its electric conversion efficiency and heat recovery performance are highly dependent on operation strategies and also on the seasonal thermal and electric load pattern. The output of the fuel cell is controlled stepwise as a function of the state of the battery and/or the storage water tank. In this study various operation strategies for cogeneration fuel cell systems are investigated. Average fuel saving rates at different seasons are calculated to find proper load management strategy. The scheme can be used to determine the optimal operating strategies of PEFCS for residential and building applications.

• 대한기계학회논문집B
• /
• 제34권4호
• /
• pp.341-347
• /
• 2010

본 연구에서는 부탄 개질기 운전조건에 따른 SOFC 시스템 효율을 모델링을 통해 분석하였다. SOFC 시스템은 크게 개질기, SOFC, 폐열 회수 장치로 구성하였다. 탄화수소 개질 반응으로 선택한 수증기 개질 반응은 흡열반응인 데에 반해 SOFC 에서 일어나는 전기화학반응은 발열반응이다. 따라서 시스템의 열관리 방법에 따라 효율이 크게 달라진다. 세부적으로 수증기 개질 반응은 운전 온도에 따라 수증기 개질 반응과 예개질 반응으로 분류되는데, 해석 결과 예개질 반응을 적용한 SOFC 시스템의 경우 더 높은 효율을 나타내었다. 시스템의 효율은 SOFC 온도 유지를 위한 열량과 온수로 회수되는 열량에 따라 달라지는데, 예개질 반응을 적용할 경우, 열관리가 더욱 효율적이어서 높은 효율을 나타내는 것으로 분석되었다.

• Nuclear Engineering and Technology
• /
• 제40권4호
• /
• pp.269-276
• /
• 2008

Operational license of WWER-440/213 units at Paks NPP, Hungary is limited to the design lifetime of 30 years. Prolongation by additional 20 years of the operational lifetime is feasible. Moreover, enhancement of the reactor thermal power by 8% will increase both the net power output and the competitiveness of the plant. Paks NPP is a pioneer considering the power up-rate and preparation of long-term operation of WWER-440/213 design. Systematic preparatory work for long-term operation of Paks NPP has been started in 2000. A regulatory framework and a comprehensive engineering practice have been developed. According to the authors view, creation of a gapless engineering system via consequent application of best practices, and feed-back of experiences together with proper consideration of WWER-440/V213 features are the decisive elements of ensuring the safety of long-term operation. That systematic engineering approach is in the focus of recent paper. Key elements of justification and measures for ensuring the safety of long-term operation of Paks NPP WWER-440/213 units are identified and discussed. These are the assessment of plant condition and review of adequacy of ageing management programmes, also the review, validation and reconstitution of time limited ageing analyses as core tasks of licence renewal.