• 한국주조공학회지
• /
• 제20권4호
• /
• pp.240-246
• /
• 2000

Surface layer properties such as composition, phase, hardness, and oxide layer condition are very important if the main failure mechanism of metals is wear. Generally, stable and dense oxide layers are known to decrease the wear rate of metals by prohibition of metallic junction occurred between bare metals. Addition of Si above 4 wt% to DCI(Ductile Cast Iron) is reported to enhance the significant oxidation resistance by forming the silicon-rich surface layer which inhibits further oxidation. And addition of up to 2 wt% Mo to high Si ductile iron produces significant increases in high temperature tensile strength, creep strength, thermal fatigue resistance and oxidation resistance. High pressure wear characteristics of unalloyed DCI(Ductile cast Iron), 4.46 wt% Si ductile iron, 4.3 wt% Si-0.52 wt% Mo ductile iron were investigated through unlubricated pin-on-disc wear test. Wear test was carried out at speed of 23m/min, under pressure of 3 MPa and 3.3 MPa. Wear surfaces of each specimen were observed by SEM to determine the wear mechanism under high pressure wear condition. Addition of Si 4.46 wt% severely deteriorated wear property of ductile iron compared to unalloyed DCI. But combined addition of Si 4.3 wt%andMo0.52wt%decreasedthefrictioncoefficient(${\mu}$)ofductileironsandremarkablydelayedthemild-severeweartransition.

• 전자공학회논문지D
• /
• 제35D권3호
• /
• pp.39-45
• /
• 1998

SrBi$_{2}$Ta$_{2}$O$_{9}$ (SBT) ferroelectric thin films for nonvolatile memory were prepared on Pt/Ti/SiO$_{2}$/Si and RuO$_{2}$/SiO$_{2}$/Si substrates by RF magnetron sputtering. The dependences of crystalline and electrical properties on the lower electrode type(Pt and RuO$_{2}$) and the annealing temperatures were investigated. SBT films regardless of their electrode types showed typeical Bi layered peroviskite crystal structures. The crystalline quality of as-deposited SBT films was improved by the rapid thermal annealing at 650.deg. C for 30 sec. The remanetn polarization of 2Pr (Pr+-Pr-) of the annealed SBT films deposited on Pt/Ti/SiO$_{2}$/Si substrates were about 11 .mu.C/cm$^{2}$ and 3 .mu.C/cm$^{2}$, respectively. The leakage currents at 3 V bias voltage were about 0.8 .mu.A/cm$^{2}$ for SBT/ Pt/Ti/SiO$_{2}$/Si and about 1 .mu.A/cm$^{2}$ for SBT/RuO$_{2}$/SiO$_{2}$/Si sample. SBT films annealed at 650 .deg. C showed no degradation in Pr values after 10$^{11}$ polarization switching cycles, indicating good fatigue properties. In addition, for SBT samples deposited on Pt/Ti/SiO$_{2}$/Si, Pr values increased to more than that of initial state, suggesting the increament of leakage current caused by repeated polarization.

• 대한간호학회지
• /
• 제13권3호
• /
• pp.106-118
• /
• 1983

The main purpose of this study is to systematically classify words indicating pain in terms of their ranks in each subclass. This study is a part of developing a Korean Pain Measurement Tool. This study didnot include exploration of each word's dimension such as sensory or affective. Eighty three Korean words tentatively classified in 19 subclasses in previous study were used for this study. At least three to six words were included in each subclass and the words were randomly placed in which each subject indicates their rank of pain degree. One hundred and fifty nursing students and one hundred clinical nurses were requested to indicate the rank of each word. One hundred and sixteen students and eighty three nurses completed the ratings for analysis. The data were collected from June 1983 to July 1983. The data using ordinal scale were analyzed by Friedman ANOVA to test significant difference between rank means. All of pain words indicated significant rank mean difference in all of 19 subclasses. Some of the words were either cancelled or replaced by other words, or rearranged for their ranks. Subclasses of which words were cancelled were 1) Simple stimulating pain, 2) Punctuate pressure, 3) peripheral nerve pain, 4) radiation pain, 5) punishment-related pain, and 6) suffering-related pain. Subclasses of which words were replaced or rearranged were 1) incisive pressure, 2) constrictive pressure, 3) dull pain, 4) tract pain, 5) digestion-related pain and 6) fear-related pain. Four subclasses such as traction pressure, thermal, cavity pressure, and fatigue- elated pain indicated significant differences among rank means in each subclasses and showed no visible overlaps of the ranks among means. Further research is needed using high level measurement of pain degree of each word and more sophisticated analysis of the pain degrees. Three pain words which would be related to chemical stimulation were newly explored and included as a new subclass. Through this study, the total number of subclasses increases from 19 to 20 and the total number of Korean words in the scale decreases from 83 to 80.

• 대한한방부인과학회지
• /
• 제29권4호
• /
• pp.80-90
• /
• 2016

Objectives: The purpose of this study is to evaluate the effects of Korean traditional treatments for Climacteric Syndrome Patients with Hwa-Byung. Methods: From February 2015 to May 2015, We treated 5 Cases Patients with Korean traditional treatments for a month. We measured treatment effects by Menopause Rating Scale (MRS), Beck's Depression Inventory (BDI), Visual Analogue Scale (VAS) and Digital Infrared Thermal Imaging (DITI). Results: After treatment, First, the scores of MRS, BDI were decreased. Second, the symptoms such as hot flush, pantalgia, palpitation, insomnia, fatigue were significantly improved. Also, the difference of 膻中 (CV17, Danjung) and 關元 (CV4, Guanyuan) temperatures were significantly decreased after treatment. Conclusions: This study suggests that Korean traditional treatments such as Gamicheonglijagam-hwan, acupuncture, moxibustion are effective on Climacteric Syndrome Patients with Hwa-Byung.

• Nuclear Engineering and Technology
• /
• 제39권3호
• /
• pp.193-206
• /
• 2007

The Korea Atomic Energy Research Institute has developed an advanced fast reactor concept, KALIMER-600, which satisfies the Generation IV reactor design goals of sustainability, economics, safety, and proliferation resistance. The concept enables an efficient utilization of uranium resources and a reduction of the radioactive waste. The core design has been developed with a strong emphasis on proliferation resistance by adopting a single enrichment fuel without blanket assemblies. In addition, a passive residual heat removal system, shortened intermediate heat-transport system piping and seismic isolation have been realized in the reactor system design as enhancements to its safety and economics. The inherent safety characteristics of the KALIMER-600 design have been confirmed by a safety analysis of its bounding events. Research on important thermal-hydraulic phenomena and sensing technologies were performed to support the design study. The integrity of the reactor head against creep fatigue was confirmed using a CFD method, and a model for density-wave instability in a helical-coiled steam generator was developed. Gas entrainment on an agitating pool surface was investigated and an experimental correlation on a critical entrainment condition was obtained. An experimental study on sodium-water reactions was also performed to validate the developed SELPSTA code, which predicts the data accurately. An acoustic leak detection method utilizing a neural network and signal processing units were developed and applied successfully for the detection of a signal up to a noise level of -20 dB. Waveguide sensor visualization technology is being developed to inspect the reactor internals and fuel subassemblies. These research and developmental efforts contribute significantly to enhance the safety, economics, and efficiency of the KALIMER-600 design concept.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.637-640
• /
• 2005

The mechanical properties of bellows, such as the extensibility and the strength can be changed depending on the shape. For the shipbuilding material, it is favorable that the fatigue lift is long due to the elastic property and the reduction of thermal stress in piping system. Nowadays, the domestic production and design of bellows are based on the E.J.M.A Code. Therefore, the design standard is in need because of much errors and lack of detailed analysis. In this study, it is attempted to find out the optimal shape of U-type ship's bellows that is applied to design of experiment using the finite element method. The effective factors, mountain height, length, thickness, and number of mountains and the length of joint are considered and the proper values are chosen for the simulation. The number of mountains are increased, the volume increases above the standard volume and the stress obviously increases. In addition, the effect of the thickness of bellows on the stress is very large. Both of the volume and stress are decreasing at a certain lower value region.

• 비파괴검사학회지
• /
• 제24권1호
• /
• pp.45-51
• /
• 2004

발전소 보일러튜브는 장시간 동안 고온고압하의 기혹한 조건으로 운전됨에 따라 크리프, 열피로와 같은 각종 열화에 의해 누설손상이 발생하고 있다. 이러한 누설손상을 실시간 감시하고 진단하기 위하여 음향방출기술을 이용한 현장적용 연구를 수행하였다. 또한 고장예측 진단기술, 튜브의 수명관리 및 설비 감시에 활용할 수 있도록 음향방출 진단시스템을 개발하여 현장에 설치하고, 보일러 운전상태에 따른 신호측정 및 평가, 누설위치 판별 등에 대해 고찰하였다. 누설감지는 저주파 및 고주파대역의 누설로 구분하여 음향방출신호를 각각 측정 및 평가하였다. 현장적용 연구결과로부터 실시간으로 보일러튜브 상태감시와 누설위치 추적이 가능하였으며, 향후 본 기술을 이용하면 발전설비 안전운전과 발전소 정지에 따른 경제적 손실 예방에 크게 기여할 것으로 기대된다.

• 한국추진공학회지
• /
• 제21권1호
• /
• pp.26-35
• /
• 2017

원심압축기 운전 중에 발생하는 고주기 피로균열이나 공진 등은 임펠러 파손의 주된 원인이다. 이러한 파손을 회피하기 위해 공진영역 운전에서도 견딜 수 있는 충분한 강도의 임펠러를 설계하거나, 공진이 발생하지 않도록 임펠러를 튜닝 한다. 이러한 회피설계는 임펠러 내부유동 및 성능특성 변화를 야기하게 된다. 본 연구에서는 밀폐형 임펠러에 대해 블레이드 두께를 증가시킨 모델과 스켈럽을 적용한 모델에 대한 유동 및 성능특성을 파악하기 위해 전산해석을 수행하였다. 전산해석 결과, 블레이드 두께 증가 모델 경우는 기본모델 대비 압력계수가 0.5% 감소하였으며, 전효율은 0.1% 감소하였다. 스켈럽 적용모델은 압력계수가 0.4% 증가하였으며, 전효율은 1.6% 감소하였다.

• 한국정보통신학회논문지
• /
• 제25권12호
• /
• pp.1935-1941
• /
• 2021

최근 다양한 분야에 적용되고 있는 딥러닝을 활용한 알고리즘 개발을 위해서는 양질의 풍부한 학습데이터가 갖춰져야 한다. 본 논문은 딥러닝 알고리즘 개발 시 활용도가 높고 정보 도출 시 유용한 광학 영상, 열화상, 음성 등의 생체신호 데이터를 동시에 수집하여 서버에 전송하는 생체신호 수집시스템을 제안한다. 수집기의 이동성을 높이기 위해 라즈베리 파이를 기반으로 제작하였고, 수집한 데이터는 무선 인터넷을 통해 서버로 전송한다. 복수의 수집기에서 동시에 데이터 수집이 가능하도록 피실험자별로 로그인을 위한 아이디를 부여했고, 이를 데이터베이스에 반영하여 데이터 관리가 용이하게 하였다. 제안하는 수집시스템의 활용방안을 보이기 위해 피로도 측정을 위한 생체신호 데이터 수집의 예시를 보인다.

• 한국전기전자재료학회논문지
• /
• 제36권3호
• /
• pp.214-225
• /
• 2023

Piezoelectric actuators, which utilize piezoelectric crystals or ceramics, are commonly used in precision positioning applications, offering high-speed response and precise control. However, the use of low-performance ceramics and expensive single crystals is limiting their versatile use in the actuator market, necessitating the development of both high-performance and cost-effective piezoelectric materials capable of delivering higher forces and displacements. The use of textured Pb (lead)-based piezoelectric ceramics formed by so-called templated grain growth method has been identified as a promising strategy to address the performance and cost issue. This review article provides insights into recent advances in texturing Pb-based piezoelectric ceramics for improved performance in actuation applications. We discussed the relevant issues in detail focusing on current challenges and emerging trends in the textured piezoelectric ceramics for their reliability and performance in actuator applications. We discussed in detail focusing on current challenges and emerging trends of textured piezoelectric ceramics for their reliability and performance in actuator applications. In conclusion, the article provides an outlook on the future direction of textured piezoelectric ceramics in actuator applications, highlighting the potential for further success in this field.