• 대한기계학회논문집A
• /
• 제26권11호
• /
• pp.2466-2473
• /
• 2002

In twin roll strip casting process, the design of casting roll is the most important equipment for producing strip. Analyses of heat transfer and deformation for the casting roll are carried out by using the finite element program, ANSYS. Both the elastic deformation and the elasto-plastic deformation under a thermal load are considered in the analysis. Optimization to minimize the volume of roll is performed under the various thermal loads such as the heat flux and the roll speed. Design variables are defined by diameters and positions of the cooling hole in the roll , Although the thermal load remarkably varies, the design variables and objective function are found to be consistent.

• Journal of Welding and Joining
• /
• 제21권6호
• /
• pp.40-45
• /
• 2003

Steel members have advantages of resisting torsion and axial compression. In design, residual stresses at the welded joint of T-shape steel pipes are one of the most important points to be considered. In this paper, characteristics of residual stresses of welded joints are clarified by carrying out 3D non-steady heat conduction analysis and 3D thermal elastic-plastic FE-analysis. According to the results, the production mechanism of residual stresses at the welded joint of T-shape steel pipe is clarified. In this paper, circumferential stresses depended on thermal histories but axial and radial stresses were more dependent on geometrical shape than thermal histories. Residual stresses in the axial direction on the lower part of pipe member were tensile, controlled by geometrical shape. However, in case of middle part, residual stresses in all the directions were controlled by thermal histories.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2214-2219
• /
• 2008

The thermal contact resistance(TCR) of nanosized contact spots has been investigated through a multiscale analysis which considers the resolution of surface topography. A numerical simulation is performed on the finite element model of rough surfaces. Especially, as the contact size decreases below the phonon mean free path, the size dependent thermal conductivity is considered to calculate the TCR. In our earlier model which follows an elastic material, the TCR increases without limits as the number of nanosized contact spots increases in the process of scale variation. However, the elastoplastic contact induces a finite limit of TCR as the scale varies. The results are explained through the plastic behavior of the two contacting models. Furthermore, the effect of air conduction in nanoscale is also investigated.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년도 춘계 학술대회 개요집
• /
• pp.77-79
• /
• 2006

To achieve high productivity of assembly hull blocks, it is important to predict welding deformations accurately and to apply these data to the production planning. In the deformation analysis of hull block, simplified methods (elastic analysis) such as inherent method, equivalent loading method and local & global approach are usually used instead of thermal-elastic-plastic analysis because of calculating time and cost. To be much more practical, these simplified methods should consider gravity effect of plate and contact condition between the plate and the positioning jig. In this research, using finite element method, practical predicting method for the welding deformation of the curved hull blocks with considering welding sequence, gravity effect and contact condition is proposed.

• Structural Engineering and Mechanics
• /
• 제75권1호
• /
• pp.101-108
• /
• 2020

The present study intends to analyze damage in thin-walled steel cylinders undergoing constant internal pressure and thermal cycles through use of anisotropic continuum damage mechanics (CDM) model coupled with nonlinear kinematic hardening rule of Chaboche. Materials damage in each direction was defined based on plastic strain and its direction. Stress and strain distribution over wall-thickness was described based on the CDM model and the return mapping algorithm was employed based on the consistency condition. Plastic zone expansion across the wall thickness of cylinders was noticeably affected with change in internal pressure and temperature gradients. Expansion of plastic zone over wall-thickness at inner and outer surfaces and their boundaries demarking elastic and plastic regions was attributed to the magnitude of damage induced over thermomechanical cycles on the thin-walled samples tested at various pressure stresses.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 추계학술발표대회 개요집
• /
• pp.17-19
• /
• 2005

To achieve high productivity of assembly hull blocks, it is important to predict welding deformations accurately and to apply these data to the production planning. In the deformation analysis of hull block, simplified methods (elastic analysis) such as inherent method, equivalent loading method and local & global approach are usually used instead of thermal-elastic-plastic analysis because of calculating time and cost. To be much more practical, these simplified methods should consider gravity effect of plate and contact condition between the plate and the positioning jig. In this research, using finite element method, practical predicting method for the welding deformation of the curved hull blocks with considering welding sequence, gravity effect and contact condition is proposed.

• 한국항공우주학회지
• /
• 제33권12호
• /
• pp.109-116
• /
• 2005

재생냉각형 액체로켓 연소기의 냉각채널 설계에 대한 탄-소성 구조설계를 수행하였다. 구조해석에 필요한 데이터를 얻기 위하여 여러 가지 온도에서 재생냉각 챔버 제작에 사용하는 구리합금의 단축인장시험을 수행하였다. 재료시험 결과 구리합금은 브레이징 공정 후에 연화되어 강도 값이 매우 저하되며 온도가 증가함에 따라 유동 응력 값이 더 작게 나타났다. 재료시험 데이터를 이용하여 냉각채널의 구조해석을 수행한 결과 채널 내부 냉각유체에 의한 내부압력보다 고온의 연소가스에 의한 열 하중에 의하여 채널의 변형이 심하게 발생함을 확인하였다. 따라서 기계적인 하중을 견딜 수 있는 한도 내에서 냉각채널의 두께를 감소시켜 열 하중을 최소화함으로서 연소기의 무게 감소, 냉각성능 향상, 그리고 구조적인 안정성을 향상시킬 수 있다는 것을 알 수 있었다.

• 소성∙가공
• /
• 제14권5호
• /
• pp.423-431
• /
• 2005

In this paper, a systematic attempt for estimating geometric dimensions of cold forgings is made by finite element method and a practical approach is presented. In the approach, the forging process is simulated by a rigid-plastic finite element method under the assumption that the die is rigid. With the information obtained from the forging simulation, die structural analysis and springback analysis of the material are carried out. In the springback analysis, both mechanical load and thermal load are considered. The mechanical load is applied by unloading the forming load elastically and the thermal load is by cooling the increased temperature due to the plastic work to the room temperature. All the results are added to predict the final dimensions of the cold forged product. The predicted dimensions are compared with the experiments. The comparison has revealed that predicted results are acceptable in the application sense.

• 한국항해항만학회지
• /
• 제26권4호
• /
• pp.435-440
• /
• 2002

잔류응력이 판의 파괴 특성에 미치는 영향의 정량적 평가를 위하여, 균열이 존재하는 CT(Compact Tension) 시편에 가스 토오치 (gas torch)를 이용한 국부 가열을 실시하여 인위적인 잔류응력을 생성시키고, 열탄소성 유한요소해석을 통하여 생성된 잔류응력장을 평가하였으며, 잔류응력이 존재하는 시편과 잔류응력이 존재하지 않는 시편에 대한 파괴인성 실험을 실시하여 이들의 결과를 파괴저항 선도 상에서 비교, 분석함으로써 압축 잔류응력이 파괴 특성에 미치는 영향을 정량화하였다.

• 대한조선학회논문집
• /
• 제38권4호
• /
• pp.66-74
• /
• 2001

선체 외판 제작을 위한 곡가공은 조선에 있어서 필수적인 공정이다. 프레스를 이용한 냉간가공과 가스토치를 이용한 열간가공이 주를 이루는데, 특히 숙련된 기능공의 작업 경험에 전적으로 의존하는 열간가공 공정에 대한 자동화 요구가 증대되어 국내외적으로 많은 연구가 진행되고 있다. 본 연구는 향후 삼각가열에 대한 효율적인 변형해석 기법을 개발하기 위한 기초 연구로서 삼각가열에 의한 판의 변형특성과 그 주요인자를 파악하고자 하였다. 실제 조선소에서 현장조건 그대로 Jang 등(2001)이 실시한 일련의 삼각가열 실험 결과를 토대로 열탄소성 해석을 위한 수치해석 모델을 개발하고 상용 구조해석 프로그램인 ANSYS를 이용하여 삼각가열에 의한 판의 변형을 시뮬레이션하였다. 또한, 총 투입 열량이 같은 경우 선상가열과 삼각가열에 의한 변형 양상을 비교하여 각 가열법에 따른 변형 특성을 보다 명확히 하였다. 마지막으로, 단위부피당 투입열량에 따른 각 변형 성분의 변화 특성을 살펴보았다.