• Journal of Aerospace System Engineering
• /
• v.17 no.5
• /
• pp.11-18
• /
• 2023

The architecture of the Fuel Thermal Management System (FTMS) in a commercial aircraft engine was built to model and simulate the fuel system. The study shows the thermal interactions between the fuel and engine lubrication oil through the mission profile of a high bypass ratio, two-spool turbofan engine. Fuel temperature was monitored as it flowed through each sub-component of the fuel system during the mission. The heat load in the fuel system strongly depended on the fuel flow rate, and was significantly increased for the periods of cruise and descent with decrease of fuel flow rate, rather than for the periods of take-off. Due to the thermal interaction in the pump housing, the fuel temperature at the outlet of the low-pressure pump was increased (4.0, 9.2, and 30.0) % over the case without thermal interaction for take-off, cruise, and descent, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.4
• /
• pp.398-406
• /
• 2022

In order to increase the electrochemical performance of thermal battery anode, LIFT anode having the same weight but a larger lithium content in electrodes was fabricated by mixing lithium, iron and titanium. By applying these electrodes, a single cell and a thermal battery were prepared, and the effect of LIFT anode on electrochemical performance was evaluated. The LIFT-applied single cell presented a better cell performance than LIFe-applied single cell at 500℃ and 550℃. The discharge performance of LIFT-applied single cell, which included the operating time (787s), specific capacity (1,683 Asg^-1), and electrode utilization (80.7%), was improved collectively compared to the LIFe applied single cell (736s, 1,245 As g^-1, and 74.6%) at 500℃. As the discharge progressed, the internal resistance of LIFT anode decreased, because the lithium migration path was formed due to the presence of large titanium particles among iron particles. These results were analyzed in terms of the microstructure of electrode using SEM. Energy density of LIFT-applied single cell also increased by 10% to 142.1 Wh kg^-1 compared to that of LIFe-applied single cell (127.4 Wh kg^-1). In addition, the LIFT-applied single cell presented a stable discharge performance for 6,500s without a short circuit which could occur by molten lithium under an open circuit voltage condition with a high pressure (4 kgf cm^-2). As observed in the high temperature thermal battery performance tests, the voltage and specific capacity of LIFT-applied thermal battery are superior to those of LIFe-applied thermal batteries, indicating that the energy density of LIFT-applied thermal batteries should remarkably increase.

• Journal of Biosystems Engineering
• /
• v.15 no.2
• /
• pp.123-133
• /
• 1990

Thermal performance of a solar heating plastic greenhouse designed for a hydroponic system was studied. The system was constructed with the air-water heat exchanger and thermal storage tank that were combined with hydroponic water beds. Experiments were carried out to investigate the daily average heat stored and released in thermal storage tank, average solar energy collection efficiency, average coefficient of performance, average oil reduction factor of thermal storage system, and the heat transfer coefficient during the nighttime in plastic greenhouse. The results obtained in the present study are summarized as follows. 1. Daily average heat stored in thermal storage tank and released from the thermal storage tank was 1,259 and $797KJ/m^2$ day, respectively. 2. The average solar energy collection efficiency of thermal storage tank was 0.125 during the experiment period. And the average coefficient of performance of thermal storage system in plastic greenhouse was 3.6. 3. The average oil reduction factor of thermal storage system and the heat transfer coefficient during the nighttime in plastic greenhouse were found to be 0.52 and $4.3W/m^2\;hr\;^{\circ}C$, respectively.

• Journal of the Korean Solar Energy Society
• /
• v.29 no.6
• /
• pp.45-55
• /
• 2009

Deterioration of the outdoor thermal environment in urban areas has become worse and worse due to the urbanization and overpopulation, etc. Most of existing researches about thermal environment are focused on the indoor environment in which the radiation heat exchange is relatively constant. However, the outdoor thermal environment is changed with time passages, because the thermal environment is highly effected by solar radiation. Thus, to simulate the outdoor thermal environment with accuracy, the solar radiation calculation should be considered, and the radiation heat exchange between building surface and ground surface should be calculated. The purpose of this study is to develop the simulator that can be possible to evaluate the outdoor thermal environment and pedestrian thermal comfort. In this paper, a new method which is coupled with convective heat transfer simulation and radiative heat transfer simulation will be proposed. And the coupled simulation method will be described through case study for outdoor thermal environment. From the results of simulation, the coupled simulation proposed in this study can assess the outdoor thermal environment with accuracy.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.28 no.4
• /
• pp.153-157
• /
• 2016

In case of metal insulation, which is produced by stacking stainless steel sheets and air layers in a multi-stack manner at a specific thickness, insulation performance will be evaluated based on thermal transmittance rather than the intrinsic physical properties of each material such as thermal conductivity. However, there is no standard for measuring thermal transmittance targeted for non-homogeneous insulation which is used in relatively high temperature conditions such as a power station. In this study, the thermal conductivity of homogeneous insulation acquired by the standardized guard hot plate method and the thermal conductivity of homogeneous insulation measured by the newly developed performance tester were compared to verify the confidence level of the tester. As a result, thermal conductivity acquired by the newly developed thermal transmittance tester was about 6% higher than the thermal conductivity measured by the existing guard hot plate method under the anticipated service temperature conditions.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.776-781
• /
• 2008

A ground heat exchanger in a GSHP system is an important unit that determines the thermal performance of a system and its initial cost. The Size and performance of this heat exchanger is highly dependent on the thermal properties. A proper design requires certain site-specific parameters, most importantly the ground effective thermal conductivity, the borehole thermal resistance and the undisturbed ground temperature. This paper is part of a research project aiming at constructing a database of these site-specific properties, especially ground effective thermal conductivity. The objective was to develop and evaluation method, and to provide this knowledge to design engineers. To achieve these goals, thermal response tests were conducted using a testing device at nearly 150 locations in Korea. The in-situ thermal response is the temperature development over time when a known heating load imposed, e.g. by circulating a heat carrier fluid through the test exchangers. The line-source model was then applied to the response test data because of its simplicity. From the data analysis, the range of ground effective thermal conductivity at various sites is $1.5{\sim}4.0\;W$/mK. The results also show that the ground effective thermal conductivity varies with grouting materials as well as regional geological conditions and groundwater flow.

• Nuclear Engineering and Technology
• /
• v.55 no.8
• /
• pp.2835-2843
• /
• 2023

After an emergency shutdown of a lead-bismuth fast reactor, thermal stratification occurs in the upper Plenum, which negatively impacts the integrity of the reactor structure and the residual heat removal capacity of natural circulation flow. The research on thermal stratification of reactors has mainly been conducted using an experimental method, a system program, and computational fluid dynamics (CFD). However, the equipment required for the experimental method is expensive, accuracy of the system program is unpredictable, and resources and time required for the CFD approach are extensive. To overcome the defects of thermal stratification analysis, a high-precision full-order thermal stratification model based on CFD technology is prepared in this study. Furthermore, a reduced-order model has been developed by combining proper orthogonal decomposition (POD) with Galerkin projection. A comparative analysis of thermal stratification with the proposed full-order model reveals that the reduced-order thermal stratification model can well simulate the temperature distribution in the upper plenum and rapidly elucidate the thermal stratification interface characteristics during the lead-bismuth fast reactor accident. Overall, this study provides an analytical tool for determining the thermal stratification mechanism and reducing thermal stratification.

• The Korean Journal of Community Living Science
• /
• v.24 no.4
• /
• pp.543-552
• /
• 2013

Physiological and subjective responses of the farmers and thermal environment during chili harvest in the open field were investigated to evaluate the thermal environments and farmers's workload. Eight career female farmers in their sixties participated as subjects both in morning work(MW, AM 9:00~10:30) and in afternoon work(AW, PM 15:00~16:30) with each lasting about 90 minutes. The results were as follows. 1) Air temperature, air humidity, globe temperature and WBGT of MW were mean $25.54^{\circ}C$, 81.82%RH, $37.72^{\circ}C$, $26.27^{\circ}C$ and AW were mean $30.63^{\circ}C$ 82.50%RH, $40.11^{\circ}C$, $30.02^{\circ}C$, respectively. By the WBGT, we evaluated that the thermal environment in the afternoon in the open field gave a thermal burden to farmers. 2) Mean skin temperature of AW($34.8{\pm}0.8^{\circ}C$) was higher than MW($33.5{\pm}1.2^{\circ}C$)(p<0.05). Clothing microclimate temperature on the chest of each work time were $31.3^{\circ}C$(MW) and $32.7^{\circ}C$(AW). Clothing microclimate humidity on the chest of each work time were over 80%RH. Heart rate were 88.5bpm(MW) and 91.7bpm(AW) respectively. 3) Farmers working in the afternoon felt uncomfortable after 45~60 min. of work and in the morning they felt uncomfortable after 90 min. of work. We evaluated that the harvesting of chilies in the open field was 'moderate work' by the physiological responses but the level of thermal burden increased over time especially in the afternoon work. It is suggested that farm workers should drink fluids between work to stay in homeostasis by sweating and to take frequent rests. Active clothing ventilation and wearing functional garments would help farm workers excrete sweat effectively.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.275-280
• /
• 1999

It was analysed the effect of pipe cooling as a measure to avoid thermal cracks due to the heat of hydration during the curing process of a massive prestressed concrete (PSC) slab. PSC slab has a complex three-dimensional shape of which the maximal and minimal thicknesses of cross-section were 2.8 and 0.95m, respectively. Steel pipes of which the diameter was 1 inch were employed for cooling. The horizontal and vertical distances between the contiguous pipes were 0.5 and 0.6m, respectively. One the four layers of cooling pipe were arranged according to the thickness of cross-section. Temperature distribution was calculated by the program developed by the authors, of which the accuracy was verified on a few published papers by the authors. Based on the temperature analysis of the cross-section which had four layers of cooing pipe, the maximum temperature of concrete interior was 54.2$^{\circ}C$ and the maximum differenced between the interior and surface temperatures of concrete was 14.$0^{\circ}C$ and, thereby, the thermal cracking index was 1.1. Upon the stress analysis, the thermal cracking index was 0.92 and the probability of thermal-crack development was 52%. Therefore, it was expected to make it possible to reduce the probability of thermal-crack development in a massive PSC slab by adopting pipe cooling.

• Food Science of Animal Resources
• /
• v.31 no.5
• /
• pp.641-648
• /
• 2011

This study investigated the effects of high pressure with or without thermal treatment on the cured color development and residual nitrite contents of model meat systems (pork, NaCl and sodium nitrite). At low nitrite levels (${\leq}50{\mu}g/g$), 200 MPa of pressure alone (P) did not develop the cured meat color (p>0.05). Thermal treatment (T) showed curing pigmentation (higher CIE L* and CIE a*), and the impacts were more effective when pressure was combined with thermal treatment (PT). In contrast, nitrite levels did not contribute to the cured meat color when ${\geq}200{\mu}g/g$ of nitrite was added to the meat. At high nitrite levels, although the typical cured color that is induced by thermal treatment did not present by pressure alone, the PT treatment still showed a pinker color with low residual nitrite content compared to the T treatment. The higher the pressure level (300 MPa), the greater the cured meat pigmentation with lower residual nitrite. Therefore, the present study demonstrates the possible application of high pressure, both for cured pigmentation and reducing residual nitrite, respective to typical thermal treatments.