• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.543-546
• /
• 2017

고체로켓 추진기관의 연소관 내부에 사용되는 연소관단열재의 열반응 특성을 평가하기 위한 모사시험장치를 개발하였다. 연소실 압력 2,500 psi, 연소시간 40 s까지 시험을 할 수 있으며, 삭마가 일어나는 조건에 대해 재료의 열반응 특성을 확인할 수 있고, 여러 시편을 동시에 상대 비교할 수 있다. 시험 장치의 안전성을 확인하기 위하여 연소실 유효평균압력 878 psi, 유효연소시간 10.7 s, 연소가스속도 100 m/s 조건에서 각기 다른 시편 4 종을 동시에 장착하여 시험을 수행하였으며, 열반응 특성 분석에 필요한 기본 데이터들, 즉 연소실의 압력-시간 선도, 재료 내부에서의 온도-시간 선도, 재료의 열파괴두께를 획득하였다.

• 한국추진공학회지
• /
• 제20권3호
• /
• pp.71-77
• /
• 2016

내열고무 성능평가 모사시험장치를 이용하여 고체로켓추진기관 연소관의 내부단열을 위해 사용하는 Kevlar/EPDM 내열고무의 압력변화에 따른 열반응 특성을 비교하였다. 연소실 유효평균압력 및 유효연소시간은 각각 1,030 psi, 35.86 s 및 1,406 psi, 36.63 s이었다. 시험후 시편의 표면 상태는 차이가 없었으며, 열파괴두께는 각각 4.10 mm 및 4.18 mm이었다. 열반응 상수 ${\xi}$, ${\zeta}$ 및 열파괴 속도 $V_{TD}$는 각각 0.7839, -0.1646, 0.1328 및 0.7836, -0.1730, 0.1346이었다. Kevlar/EPDM 내열고무의 열반응 특성은 압력변화에 따른 차이를 보이지 않았다.

• 토지주택연구
• /
• 제9권4호
• /
• pp.33-42
• /
• 2018

As a radiant heating panel gets more popularity, the need to study on evaluation method of thermal output of the panel also becomes increasing. Generally, the chamber using method is applied to evaluate the thermal output through an experiment. However, the chamber using method cannot be used due to the limitations on space and cost. EN1264 addresses the test equipment to evaluate the thermal output by using simpler experimental setup, and introduces application method in detail. However, there is not enough description of control methods to meet the experiment condition, and it is difficult to meet this when practical experiment. Therefore, this paper analysed the control error factors of when the thermal output experiment is performed. When EN1264 method is applied to evaluate the thermal output of the radiant floor heating panel, the error factor which is caused by the characteristic of test equipment cannot be removed by the control methods of chamber using method. In addition, the error factor can be occurred at the element which is located out of the control system. These possible error factors are defined as the characteristic error factors.

• 한국화재소방학회논문지
• /
• 제9권1호
• /
• pp.20-29
• /
• 1995

The sprinkler head is a component of the sprinkler system intended to discharge water for automatic detection and extinguishment of fires. On this study, thermal characteristic values affecting the sensitivity of the fusible alloy type sprinkler head were obtained and analyzed under heated air stream condition which had constant temperature and velocity. The experiment was carried out under the forced convection condition with both the conductive heat loss considered and neglected. The thermal characteristic values of the sprinkler head were obtained in accordance with the material and shape of the heat responsive element and the conditions of the main body.

• 대한전기학회논문지:전력기술부문A
• /
• 제54권10호
• /
• pp.487-495
• /
• 2005

This paper reviews the characteristic of thermal and temperature of oil field cable in transient state such as grounding fault and lightning surge. For analysis in various conditions, many actual underground power cable systems are modeled using ATP. These results are applied for the examination of temperature increase when the single line to ground fault by the breakdown of insulation part and hitting of lightning surge are occurred. The inner part temperature of OF cable is analysed according to the various kinds of cable using the thermal model of transient state. The temperature increase of sheath and crossbonded lead bv fault current is also analysed using IEC 60949.

• 한국태양에너지학회 논문집
• /
• 제30권2호
• /
• pp.33-38
• /
• 2010

The perimeter zone is space which receives a significant effect of ambient condition, it is necessary to improve the thermal performance in order to building energy saving. For this reason, a lot of study about the active approach is being performed, such as perimeter-less air conditioning system. But the performance of the perimeter zone is necessary to improve, through the passive approach. Therefore, the purpose of this study is to provide basic materials of energy-saving design of perimeter zone, based of the PAL that simulation changing the thickness of insulation and the rate of windows.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.747-748
• /
• 2013

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 춘계학술대회 논문집
• /
• pp.553-554
• /
• 2008

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• 제12권1호
• /
• pp.25-32
• /
• 2008

A pin fin is optimized based on the increasing rate of heat loss by using a two-dimensional analytic method. The optimum heat loss, corresponding optimum thermal resistance and fin length are presented as a function of the fin base thickness, convection characteristic numbers ratio, fin outer radius and ambient convection characteristic number. One of the results shows that both the optimum heat loss and fin length decrease linearly whereas the optimum thermal resistance increases very slightly with increase of the fin base thickness.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.121-122
• /
• 2013