• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 추계학술대회
• /
• pp.515-518
• /
• 2006

This paper presents the friction and wear characteristics of contact type sealing unit for a water turbine of a small hydro-power generation, which Is to stop a leakage of a circulating water from a outside of an impeller to an inside of a rolling bearing. The surface wear strongly affect to the seal life of a mechanical face seal. In this study, the hardness of a stainless steel in which is a heat-treated is 892.8 in Vickers hardness and the hardness of silicone carbide of SiC is 714.1 in Vickers hardness. The surface hardness of a heat-treated stainless steel is 25% high compared with that of a ceramic material of SiC. The contact modes of rubbing surfaces aye a dry friction a water film friction and a mixed friction that is contaminated by a dust, silt and moistures, etc. These two factors of a contact rubbing modes and a material property are very important parameters on the tribological performance such as a friction and wear between a seal ring and a seal seat. The experimental result shows that the surface hardness of a seal material is very important on the friction coefficient and a wear volume. Thus, the results recommend higher hardness of a seal material, which may reduce a friction loss and increase a wear life of primary seal components

• 설비공학논문집
• /
• 제28권1호
• /
• pp.29-34
• /
• 2016

The friction factor unit was studied to find a more economic alternative compared to the conventional 30 mmAq/m. The pipe and pump for cooling water piping used in a failing were selected, and the friction factor unit was changed to calculate the pipe diameter and the brake shaft power. Based on current electric charges, After the brake shaft power was converted into operational costs based on current electric charges, then an economic analysis was conducted considering that incorporated the initial installation costs and operational costs for the pump. We found that the friction factor unit when using 20 mmAq/m is more economical than that with 30 mmAq/m, if the piping is used for more than 4 years. The small friction factor unit is desirable when the piping is used for quite a long period of time, and the selection of a more economic friction factor unit should considering the period of usage will be important.

• 한국지반공학회논문집
• /
• 제39권6호
• /
• pp.21-30
• /
• 2023

현장타설말뚝의 연암 근입부의 단위주면마찰력을 산정하는 방법 중 암반 벽면거칠기에 의한 산정 방법이 있다. 현장타설말뚝의 굴착 시공 시 암반 굴착공에 거칠기 장치를 설치하고 벽면 거칠기 모양을 측정하고 그 결과를 이용하여 주면마찰력을 산정하는 것이다. 본 연구에서는 암반벽면의 거칠기를 직접 측정한 결과와 하중전이 시험결과를 비교분석하여 거칠기시험에 의한 단위주면마찰력을 말뚝의 발생 변위에 대응하는 단위 주면마찰력으로 변환할 수 있도록 저감계수 R_f = -0.14n + 1.48(여기서, n은 하중전이시험에서 도출된 발생변위 δ를 말뚝직경 D로 나눈 변위비)을 제안하였다.

• 한국생산제조학회지
• /
• 제20권6호
• /
• pp.685-691
• /
• 2011

The Bearing preload units are used for stable rotational movements of high speed spindles. The feeding mechanism of the preload unit is important to prevent overheat of bearings and to keep constant bearing load under thermal deformation of spindle unit. In this study, ball slide guide and ball bush as feeding mechanism of preload unit are selected. The maximum static friction force, radial stiffness and damping ratio of ball slide guide with ball load, ball number and ball size are widely investigated. In conclusion, the surface of ball slide guide must be heat treated to reduce static friction force. The number and size of ball are increased to control sensitive bearing preload force.

• 한국지반공학회논문집
• /
• 제35권12호
• /
• pp.7-13
• /
• 2019

현장타설말뚝인 경우에 연암 소켓부의 단위주면마찰응력을 산정하는 방법 중 벽면 거칠기에 의한 산정 방법이 있다. 이 방법은 현장타설말뚝을 시공하기 위한 굴착 단계에서 거칠기 측정 장치를 굴착공에 설치하여 암반 벽면의 거칠기 양상을 측정하여 주면마찰력을 산정하는 것이다. 본 연구에서는 현장타설말뚝의 암반 소켓부 벽면의 거칠기 양상을 천공홀에서 직접 측정하였으며 그 결과를 이용하여 암반의 주면마찰력 특성을 파악하고자 한다. 그리고, 거칠기 시험 결과를 검증하기 위하여 동일 말뚝에 정재하시험 및 하중전이시험을 수행하였다.

• Tribology and Lubricants
• /
• 제22권6호
• /
• pp.314-319
• /
• 2006

In this paper, the friction and wear characteristics of contact type sealing unit far a water turbine have been presented. The sealing unit for a small hydropower generation is to stop a leakage of circulating water from an outside of an impeller to an inside of a rolling bearing. The friction heating between a seal ring and a seal seat may radically increase a surface temperature in which increase a power loss and wear on the rubbing surface. The surface wear strongly affect to the seal life of a mechanical face seal. In this study, the hardness of a stainless steel in which is a heat-treated is 892.8 in Victors hardness and the hardness of silicone carbide of SiC is 714.1 in Victors hardness. The surface hardness of a heat-treated stainless steel is 25% high compared with that of a ceramic material of SiC. The contact modes of rubbing surfaces are a dry friction, a water film friction and a mixed friction that is contaminated by a dust, silt, and moistures, etc. These two factors of a contact rubbing modes and a material property are very important parameters on the tribological performance such as a friction and wear between a seal ring and a seal seat in primary sealing unit. The experimental result shows that the surface hardness of a seal material is very important on the friction coefficient and a wear volume. Thus, the results recommend higher hardness of a seal material, which may reduce a friction loss and increase a wear life of primary seal components.

• 한국가스학회지
• /
• 제10권2호
• /
• pp.27-32
• /
• 2006

본 논문은 다수의 볼과 접촉하는 두개의 실린더 사이에서 발생하는 접촉응력과 마찰력을 유한요소법으로 해석하였다. LPG 충전기는 구름마찰 운동을 위해 다수의 볼이 평행한 두개의 실린더와 경사진 두개의 실린더 레이스에서 구름마찰 운동을 한다. FEM 해석결과에 의하면, SiC 볼과 SUS 304 볼은 주어진 수직하중, 즉 압축력에 대하여 높은 접촉응력과 마찰력 손실을 보여주고 있다. 반면에 PEEK 볼을 두개의 실린더에 대하여 구름마찰 운동을 유지하면, 대단히 낮은 접촉응력과 마찰력 손실을 나타내는 것으로 보아 폴리머 소재의 사용은 저마찰 접촉특성을 잘 구현하고 있다할 수 있다. 여기에 두개의 실린더가 평행하게 구름마찰 접촉운동을 하느냐, 또는 경사진 상태에서 구름마찰 운동을 하느냐에 따라 접촉거동 특성이 크게 달라지므로 특히 두개 실린더 사이의 상대적 경사도는 극도로 억제되어야 우수한 설계가 된다.

• 한국철도학회논문집
• /
• 제14권2호
• /
• pp.109-115
• /
• 2011

고속철도 KTX 차량의 답면제동은 전기제동이 작용하지 않는 저속에서 열차를 정거장의 정위치에 정차시킬 때 주로 사용되는데 그 동안 균열발생, 제륜자 키 탈락 등 잦은 고장이 발생하였다. 본 연구에서는 이러한 고장의 원인을 규명하고 각 고장에 대해 해결책을 제시하고 시험평가를 통하여 개선효과를 검증하였다. 제륜자 키와 캠의 강도향상과 제륜자 마찰재 지지판의 강도향상은 제륜자 마찰재의 균열발생을 약간 줄이는 효과는 있었다. 지지판의 강도향상, 구조개선과 함께 제륜자의 재질을 변경하였을 때 마찰재에는 균열이 거의 발생되지 않았다.

• Carbon letters
• /
• 제4권3호
• /
• pp.117-120
• /
• 2003

Asbestos is being replaced throughout the world among friction materials because of its carcinogenic nature. This has raised an important issue of heat dissipation in the non-asbestos brake pad materials being developed for automobiles etc. It has been found that two of the components i.e. carbon fibres as reinforcement and graphite powder as friction modifier, in the brake pad material, can playa vital role in this direction. The study reports the influence of these modifications on the thermal properties like coefficient of thermal expansion (CTE) and thermal conductivity along with the mechanical properties of nonasbestos brake pad composite samples developed in the laboratory.

• Carbon letters
• /
• 제5권1호
• /
• pp.6-11
• /
• 2004

In spite of unparalleled combination of essential material properties for brake linings and clutch facings, replacement for asbestos is seriously called for since it is a health hazard. Once asbestos is replaced with other material then composition and properties of brake pad changes. In certain cases hardness of the material may be high enough to affect the rotor material. In this study, hardness of the brake pad has been controlled using suitable reinforcement materials like glass, carbon and Kevlar pulp. Brake pad formulations were made using CNSL (cashew net shell liquid) modified phenolic resin as a binder, graphite or cashew dust as a friction modifier and barium sulphate, talc and wollastonite as fillers. Influence of each component on the hardness value has been studied and a proper formulation has been arrived at to obtain hardness values around 35 on Scleroscopic scale. Friction and wear properties of the respective brake pad materials have been measured on a dynamometer and their performance was evaluated.