• 대한기계학회논문집A
• /
• 제26권5호
• /
• pp.932-938
• /
• 2002

In structural applications, brittle materials such as soda-lime glasses and ceramics are usually subjected to multiaxial stress state. Brittle materials with cracks or damage by foreign object impacts are apt to fracture abruptly from cracks, because of their properities of very high strength and low fracture toughness. But in most cases, the residual strength of structural members with damage has been tested under uniaxial stress condition such as the 4-point bend test. Depending upon the crack pattern developed, the strength under multiaxial stress state might be different from the one under uniaxial. A comparative study was carried out to investigate the influence of stress state on the residual strength evaluation. In comparable tests, the residual strength under biaxial stress state by the ball-on-ring test was greater than that under the uniaxial one by the 4-point bend test, when a small size indendation crack was introduced. In the case that crack having an angle of 90deg. to the applied stress direction, the ratio of biaxial to uniaxial flexure strength was about 1.12. The residual strength was different from crack angles to loading direction when it was evaluated by the 4-point bend test. The ratio of residual strength of 45deg. crack to 90deg. one was about 1.20. In the case of specimen cracked by a spherical impact, it was shown that an overall decrease in flexure strength with increasing impact velocity, and the critical impact velocity for formation of a radial and/or cone crack was about 30m/s. In those cases that relatively large cracks were developed as compared with the case of indented cracks, the ratio of residual strength under biaxial stress state to one uniaxial became small.

• Computers and Concrete
• /
• 제3권2_3호
• /
• pp.145-161
• /
• 2006

This article involves architecting prototype-fuzzy expert system for designing the nominal cover thickness by means of fuzzy inference for quantitatively representing the environment affecting factor to reinforced concrete in chloride-induced corrosion environment. In this work, nominal cover thickness to reinforcement in concrete was determined by the sum of minimum cover thickness and tolerance to that defined from skill level, constructability and the significance of member. Several variables defining the quality of concrete and environment affecting factor (EAF) including relative humidity, temperature, cyclic wet and dry, and the distance from coast were treated as fuzzy variables. To qualify EAF the environment conditions of cycle degree of wet-dry, relative humidity, distance from coast and temperature were used as input variables. To determine the nominal cover thickness a qualified EAF, concrete grade, and watercement ratio were used. The membership functions of each fuzzy variable were generated from the engineering knowledge and intuition based on some references as well as some international codes of practice.

• Safety and Health at Work
• /
• 제7권4호
• /
• pp.307-316
• /
• 2016

Background: Resilience engineering (RE) is a new paradigm that can control incidents and reduce their consequences. Integrated RE includes four new factors-self-organization, teamwork, redundancy, and fault-tolerance-in addition to conventional RE factors. This study aimed to evaluate the impacts of these four factors on RE and determine the most efficient factor in an uncertain environment. Methods: The required data were collected through a questionnaire in a petrochemical plant in June 2013. The questionnaire was completed by 115 respondents including 37 managers and 78 operators. Fuzzy data envelopment analysis was used in different ${\alpha}$-cuts in order to calculate the impact of each factor. Analysis of variance was employed to compare the efficiency score means of the four abovementioned factors. Results: The results showed that as ${\alpha}$ approached 0 and the system became fuzzier (${\alpha}=0.3$ and ${\alpha}=0.1$), teamwork played a significant role and had the highest impact on the resilient system. In contrast, as ${\alpha}$ approached 1 and the fuzzy system went toward a certain mode (${\alpha}=0.9$ and ${\alpha}=1$), redundancy had a vital role in the selected resilient system. Therefore, redundancy and teamwork were the most efficient factors. Conclusion: The approach developed in this study could be used for identifying the most important factors in such environments. The results of this study may help managers to have better understanding of weak and strong points in such industries.

• The Plant Pathology Journal
• /
• 제28권3호
• /
• pp.248-258
• /
• 2012

Potato (Solanum tuberosum) is one of the most important food crops worldwide and yields of potato can be affected by virus infection. While more than 40 viruses have been found in potato, only nine viruses (potato leafroll virus, potato viruses A, M, S, V, X and Y, potato moptop virus and tobacco rattle virus) and one viroid (potato spindle tuber viroid) have a significant economic impact on potato, worldwide. This review describes the geographical distribution of the most important viruses infecting potato and the genes for resistance or tolerance that have been identified against these various infectious agents. In some cases such resistance genes have been found only in other Solanum species. Few genes for resistance to the vectors of these viruses have been obtained and even fewer have been deployed successfully. However, transgenic resistance in potato has been achieved against seven of these disease agents.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.820-824
• /
• 1997

In order to investigate the effect of surface treatment(Anodizing) and rolling in Al 5083-H131 alloy, ballistic testing was conducted. Ballistic resistance of these materials. was measured by protection ballistic limit(V$_{50}$), a statical velocity with 50% probability for incomplete penetration. Fracture behaviors and ballistic tolerance, described by penetration modes, are observed respectfully, resulting from V$_{50}$ test and Projectile Through Plates(PTP) test at velocities greater than V$_{50}$. PTP tests were conducted with 0$^{\circ}$obliquity at room temperature were also conducted with projectiles that were able to achieve near or complete penetration during PTP tests. Resistance to penetration, and penetration modes of Al 5052-H34 alloy, compared to those of Al 5083-H131 alloy.alloy.

• Asian-Australasian Journal of Animal Sciences
• /
• 제30권5호
• /
• pp.700-711
• /
• 2017

Objective: The current study aimed to investigate the impact of high-fat diets composed of different animal and vegetable fat sources on serum metabolic health markers in Japanese quail, as well as the overall lipid content and fatty acid profiles of the edible bird tissues following significantly increased dietary lipid supplementation. Methods: Fifty seven male quail were divided into six groups and fed either a standard diet or a diet enriched with one of five different fats (22% coconut oil, lard, palm oil, soybean oil, or sunflower oil) for 12 weeks. The birds were subjected to an oral glucose tolerance test following the feeding period, after which they were euthanized and blood, liver, breast, and thigh muscle samples collected. Total fat content and fatty acid profiles of the tissue samples, as well as serum uric acid, triglyceride, cholesterol, total protein, albumin, aspartate transaminase, and total bilirubin concentrations were assessed. Results: High-fat diet feeding had no significant effects on the glucose tolerance of the birds. Dietary fatty acid profiles of the added fats were reflected in the lipid profiles of both the liver and breast and thigh muscle tissues, indicating successful transfer of dietary fatty acids to the edible bird tissues. The significantly increased level of lipid inclusion in the diets of the quail used in the present study was unsuccessful in increasing the overall lipid content of the edible bird tissues. Serum metabolic health markers in birds on the high-fat diets were not significantly different from those observed in birds on the standard diet. Conclusion: Thus, despite the various high-fat diets modifying the fatty acid profile of the birds' tissues, unlike in most mammals, the birds maintained a normal health status following consumption of the various high-fat diets.

• Advances in aircraft and spacecraft science
• /
• 제6권2호
• /
• pp.145-156
• /
• 2019

As the industrial desire for a step change in productivity within the manufacture of composite structures increases, so does the interest in Through-Thickness Reinforcement technologies. As manufacturers look to increase the production rate, whilst reducing cost, Through-Thickness Reinforcement technologies represent valid methods to reinforce structural joints, as well as providing a potential alternative to mechanical fastening and bolting. The use of tufting promises to resolve the typically low delamination resistance, which is necessary when it comes to creating intersections within complex composite structures. Emerging methods include the use of 3D woven connectors, and orthogonally intersecting fibre packs, with the components secured by the selective insertion of microfasteners in the form of tufts. Intersections of this type are prevalent in aeronautical applications, as a typical connection to be found in aircraft wing structures, and their intersections with the composite skin and other structural elements. The common practice is to create back-to-back composite "L's", or to utilise a machined metallic connector, mechanically fastened to the remainder of the structure. 3D woven connectors and selective Through-Thickness Reinforcement promise to increase the ultimate load that the structure can bear, whilst reducing manufacturing complexity, increasing the load carrying capability and facilitating the automated production of parts of the composite structure. This paper provides an overview of the currently available methods for creating intersections within composite structures and compares them to alternatives involving the use of 3D woven connectors, and the application of selective Through-Thickness Reinforcement for enhanced damage tolerance. The use of tufts is investigated, and their effect on the load carrying ability of the structure is examined. The results of mechanical tests are presented for each of the methods described, and their failure characteristics examined.

• 한국강구조학회 논문집
• /
• 제23권2호
• /
• pp.199-210
• /
• 2011

사장교의 케이블은 타 부재에 비해 단면적이 매우 작고 고응력 상태이므로 진동에 매우 민감한 부재이다. 따라서 사장교 케이블의 충격계수는 실제 차량의 주행으로 발생하는 동적 효과를 반영하여 평가하는 것이 합리적이다. 이에 본 연구에서는 차량 중량, 케이블 모델, 노면조도, 차량속도 및 차량간격의 설계변수를 고려하여 중앙경간 230m 및 540m의 강합성 사장교를 대상으로 차량 이동하중 해석을 수행하여 케이블의 충격계수를 평가하고, 현재 실무에서 사용되고 있는 영향선을 이용한 방법과 비교하였다. 본 연구에 사용된 노면조도는 ISO 8608 규정에 근거하여 랜덤 생성하였으며, 생성 회수에 따른 케이블 충격계수의 수렴 추이를 분석함으로써 결과의 신뢰도를 확보하였다. 또한, 차량모델은 9-자유도를 갖는 트랙터-트레일러 형식의 트럭 모델을 적용하였으며 차량의 운동방정식은 Lagrange운동방정식으로부터 유도하였다. 해석 대상 교량은 3차원 유한요소모델로 구축하였으며 보강형과 주탑은 보요소, 케이블은 등가탄성계수를 갖는 트러스요소를 사용하였다. 이동하중으로 인한 교량-차량 상호작용 해석에는 직접적분법을 사용하였으며, 교량의 변위 오차율이 허용 범위 내에 수렴될 때까지 반복 해석을 수행하였다. 그 결과, 실제 차량의 주행으로 발생하는 동적 효과를 고려하지 못하는 영향선 기법은 차량 이동하중 해석에 비해 측경간 단부 케이블의 충격계수를 과소평가할 수 있는 것으로 나타났다.

• Journal of Microbiology and Biotechnology
• /
• 제18권5호
• /
• pp.805-814
• /
• 2008

Liming of acidic soils can prevent aluminum toxicity and improve crop production. Some maize lines show aluminum (Al) tolerance, and exudation of organic acids by roots has been considered to represent an important mechanism involved in the tolerance. However, there is no information about the impact of liming on the structures of bacterial and fungal communities in Cerrado soil, nor if there are differences between the microbial communities from the rhizospheres of Al-tolerant and Al-sensitive maize lines. This study evaluated the effects of liming on the structure of bacterial and fungal communities in bulk soil and rhizospheres of Al-sensitive and Al-tolerant maize (Zea mays L.) lines cultivated in Cerrado soil by PCR-DGGE, 30 and 90 days after sowing. Bacterial fingerprints revealed that the bacterial communities from rhizospheres were more affected by aluminum stress in soil than by the maize line (Al-sensitive or Al-tolerant). Differences in bacterial communities were also observed over time (30 and 90 days after sowing), and these occurred mainly in the Actinobacteria. Conversely, fungal communities from the rhizosphere were weakly affected either by liming or by the rhizosphere, as observed from the DGGE profiles. Furthermore, only a few differences were observed in the DGGE profiles of the fungal populations during plant development when compared with bacterial communities. Cloning and sequencing of 16S rRNA gene fragments obtained from dominant DGGE bands detected in the bacterial profiles of the Cerrado bulk soil revealed that Actinomycetales and Rhizobiales were among the dominant ribotypes.

• Asian-Australasian Journal of Animal Sciences
• /
• 제17권5호
• /
• pp.638-642
• /
• 2004

In Australia, many cropping areas are affected by salt. In these regions, Chenopodiaceous plants, such as Atriplex, Kochia and Bassia spp have been planted to improve soil conditions. These plants have become invaluable feed resources for grazing animals in dry summers, but have a high sodium content. To assess the impact of high salt intake on grazing deer, two experiments were conducted. The first experiment used 30 fallow weaner deer to examine the effect of salt level in the diet on feed intake, water intake and body weight of fallow deer. Salt was added to lucerne chaff at 0, 1.5, 3.0, 4.5 and 6% and fresh water was offered all the time. Increasing the salt level in the diet from 0 to 6% didn't affect feed intake, osmotic pressure and mineral concentration in blood of fallow deer. However, water intake was significantly higher (p<0.05) in deer fed diets containing more than 3% salt. Body weight was lower (p${\leq}$0.056) for fallow deer in July and August when salt content was over 3%, suggesting they can ingest over 15 g sodium/day without significant depression in both feed intake and growth rate if the fresh water is available. In the second experiment, 18 red weaner deer were fed lucerne chaff diets containing 1.5, 4.5 and 6.0% salt with 6 deer/diet. The results revealed that feed intake and blood osmotic pressure were similar (p>0.05) for red deer fed different levels of salt although the feed intake declined from 1.91 to 1.67 kg with the increase of salt level from 1.5% to 6.0% in the diet. Water intake was significantly higher for deer fed diets containing over 4.5% salt, but there was no difference in body weight during the experiment. However, no recommendation can be made on the salt tolerance of red deer due to limited increment of salt level in the diet.