• 제목/요약/키워드: Test Setup Design

검색결과 76건 처리시간 0.035초

고 형상비 UV LIGA 공정을 위한 낮은 내부응력의 SU-8 도금틀 제작 (SU-8 Mold Fabrication with Low Internal Stress and High Aspect Ratio for UV LIGA Process)

  • 장현기;김용권
    • 대한전기학회논문지:전기물성ㆍ응용부문C
    • /
    • 제48권8호
    • /
    • pp.598-604
    • /
    • 1999
  • This paper describes the research to minimize the film stress and maximize the aspect ratio of photoresist structure, especially about SU-8 for electroplating mold. UV LIGA process using SU-8 allows fabricating high aspect ratio polymer structures. However, it is hard to get fine patterns in the high aspect ratio structures because of high internal stress and difficulty of removing SU-8. The purpose of this paper is to setup the process condition for the obtainment of both low film stress and high aspect ratio and to find design rules that make the pattern be less dependent on stress problem. Firstly, the process of heat treatment and exposure of SU-8 are proposed. These two conditions control the amount of cross-linkage in polymer structure, which is the most important parameter of both pattern generation and remaining stress. Heat treatment is dealed with soft bake and post-exposure-bake. Temperature and time duration of each step are varied with heat treatment condition. Some test patterns are fabricated to evaluate the proposed process. Nickel electroplating is performed with the mold fabricated through the proposed process to confirm the SU-8 as a good electroplating mold.

  • PDF

산업용 서보 구동 시스템을 위한 자동 P/PI 속도 제어기 설계 (Automatic P/PI speed controller design for industry servo drives)

  • 배상규;석줄기;김경태;이동춘
    • 대한전기학회:학술대회논문집
    • /
    • 대한전기학회 2003년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
    • /
    • pp.179-181
    • /
    • 2003
  • Conventional P/PI speed controller of today's servo drives should be manually tuned the controller switching set-point by trial-and-errors, which may translate the drive system down-time and loss of productivity. The adjustable drive performance is heavily dependent on the qualify of the expert knowledge and becomes inadequate in applications where the operating conditions change in a wide range, i.e., tracking command, cceleration/deceleration time, and load disturbances. In this paper, the demands on simple controls/setup are discussed for industry servo drives. Analyzing the frequency content of motor torque command, P/PI control mode switching is automatically peformed with some prior knowledge of the mechanical dynamics. The dynamic performance of the proposed scheme assures a desired tracking response curve with minimal oscillation and settling time over the whole operating conditions. For comprehensive comparison of traditional P/PI control scheme, extensive test is carried out on actual servo system.

  • PDF

초전도 논리연산자의 개발 (Development of Superconductive Arithmetic and Logic Devices)

  • 강준희
    • Progress in Superconductivity
    • /
    • 제6권1호
    • /
    • pp.7-12
    • /
    • 2004
  • Due to the very fast switching speed of Josephson junctions, superconductive digital circuit has been a very good candidate fur future electronic devices. High-speed and Low-power microprocessor can be developed with Josephson junctions. As a part of an effort to develop superconductive microprocessor, we have designed an RSFQ 4-bit ALU (Arithmetic Logic Unit) in a pipelined structure. To make the circuit work faster, we used a forward clocking scheme. This required a careful design of timing between clock and data pulses in ALU. The RSFQ 1-bit block of ALU used in this work consisted of three DC current driven SFQ switches and a half-adder. We successfully tested the half adder cell at clock frequency up to 20 GHz. The switches were commutating output ports of the half adder to produce AND, OR, XOR, or ADD functions. For a high-speed test, we attached switches at the input ports to control the high-speed input data by low-frequency pattern generators. The output in this measurement was an eye-diagram. Using this setup, 1-bit block of ALU was successfully tested up to 40 GHz. An RSFQ 4-bit ALU was fabricated and tested. The circuit worked at 5 GHz. The circuit size of the 4-bit ALU was 3 mm ${\times}$ 1.5 mm, fitting in a 5 mm ${\times}$ 5 mm chip.

  • PDF

반동방식 충격기구의 완충시스템 해석 (Analysis of Isolation System for Impulsive Force Device with Recoil Mechanism)

  • 김효준;류봉조
    • 한국소음진동공학회논문집
    • /
    • 제15권3호
    • /
    • pp.272-279
    • /
    • 2005
  • 이 논문에서는 프로토타입(prototype) 고충격력 기구에 대한 최적의 절연시스템이 연구된다. 이 목적을 위해 첫째, 고충격력 기구의 특정한 작동조건하에서 인체의 거동과 전달력이 고안된 시험 장치를 이용한 실험을 통해 분석된다. 최적 동흡진기를 설계하기 위하여, 파라미터 최적과정이 충격량과 전달력의 실험결과를 토대로 한 단순화된 절연시스템 모델을 사용하여 이루어진다. 최종적으로, 충격완화 변위와 전달력의 구속조건을 만족시키는 파라미터 하에서, 프로토타입 고충격력 기구에 대해 최적 설계된 절연시스템의 성능이 실험에 의해 평가된다.

94.8dB의 SNR을 갖는 1-bit 4차 고성능 델타-시그마 모듈레이터 설계 (Design of a 94.8dB SNR 1-bit 4th-order high-performance delta-sigma Modulator)

  • 최영길;노형동;변산호;이현태;강경식;노정진
    • 대한전자공학회:학술대회논문집
    • /
    • 대한전자공학회 2006년도 하계종합학술대회
    • /
    • pp.507-508
    • /
    • 2006
  • High performance delta-sigma modulator is developed for audio-codec applications(i.e.. 16-bit resolution at a 20kHz signal bandwidth). The modulator is realized with fully-differential switched capacitor integrators. All stages employ a single-stage folded-cascode amplifier. The presented delta-sigma modulator when clocked at 3.2MHz achieves 85.2dB peak-SNDR and 94.8dB SNR. This modulator is designed in a SAMSUNG $0.18{\mu}m$ CMOS process. Finally, this paper shows the test setup and FFT result gained from delta-sigma modulator chip designed for audio applications.

  • PDF

전화기 기능을 포함한 홈 게이트웨이 접속용 VOIP 장비 설계 및 구현 (Design and Implementation of VoIP Equipment including Telephone Function for Home Gateway Connection)

  • 이용수;정광욱;정중수
    • 한국콘텐츠학회논문지
    • /
    • 제4권4호
    • /
    • pp.123-131
    • /
    • 2004
  • 오늘날 인터넷은 가장 주목받고 있는 정보통신 혁명을 주도하였다. 가정이나 소규모 오피스에서는 홈 게이트웨이를 통해 인터넷에 접속하여 데이타와 음성 등의 다양한 서비스를 제공받고 있는 상황이다. 홈 게이트웨이 장비에 접속되어 인터넷 전화, 데이타 통신을 하는 통신장비의 개발은 매우 활발하게 이루어지며, 그 제품 또한 매우 다양하다. 본 논문에서는 흠 게이트웨이와 PC에 접속되는 두 개의 이더넷 포트 접속용 VoIP 전화기 기능을 보유한 장비를 임베디드 환경에서 설계 및 구현 과정을 제시하였다. 개발 환경으로는 ST Microelectronics사의 STLC1502를 싱글 칩 솔루션으로, VxWorks를 운영체제로, 코딩 언어를 ANSI C 언어로 사용하였다. 또한 개발된 시스템의 성능해석을 위하여 인터넷과의 통신시 호 설정 시간과 해제시간을 측정한 호 처리 능력과 파일 전달을 수행한 데이타 처리속도를 성능 분석 파라메터로 제시하였다 이때 호 설정 시간과 해제시간은 약 95ms가 소요되어 초당 약 10개의 호를 처리하였으며, 파일 전달은 서버 및 플라이언트 환경에서 5.7 Mbps로 처리할 수 있다. 따라서 실제 인터넷 환경에서 본 시스템을 사용하여 호 처리 및 데이타 전달시 만족한 성능을 얻었다.

  • PDF

전열화학추진용 2.4MJ 펄스파워전원의 설계와 동작특성(I) (Design and Operation Characteristics of 2.4MJ Pulse Power System for Electrothermal-Chemical(ETC) Propulsion(I))

  • 진윤식;이홍식;김종수;조주현;임근희;김진성;추증호;정재원;황동원
    • 대한전기학회:학술대회논문집
    • /
    • 대한전기학회 2000년도 하계학술대회 논문집 C
    • /
    • pp.1868-1870
    • /
    • 2000
  • As a drive for an ETC (Electro-thermal Chemical) launcher, a large pulse power system of a 2.4MJ energy storage was designed, constructed and tested. The overall power system consists of eight capacitive 300kJ energy storage banks. In this paper we describe the design features, setup and operation test result of the 300kJ pulsed power module. Each capacitor bank of the 300kJ module consists of six 22kV 50kJ capacitors. A triggered vacuum switch (TVS-43) was adopted as the main pulse switch. Crowbar diode circuits, variable multi-tap inductors and energy dumping systems are connected to each high power capacitor bank via bus-bars and coaxial cables. A parallel crowbar diode stack is fabricated in coaxial structure with two series 13.5kV, 60kA avalanche diodes. The main design parameters of the 300kJ module are a maximum current of 180kA and a pulse width of 0.5 - 3ms. The electrical performances of each component and current output variations into resistive loads have been investigated.

  • PDF

헬륨가스루프 시험용 공정열교환기에 대한 고온구조해석 모델링(II) (High-Temperature Structural Analysis Model of the Process Heat Exchanger for Helium Gas Loop (II))

  • 송기남;이형연;김찬수;홍성덕;박홍윤
    • 대한기계학회논문집A
    • /
    • 제34권10호
    • /
    • pp.1455-1462
    • /
    • 2010
  • 초고온가스로에서 생성된 $950^{\circ}C$ 정도의 초고온 열을 이용하여 수소를 경제적이며 또한 대량으로 생산하기 위한 시스템이 원자력수소생산시스템이며, 이 시스템에서 공정열교환기는 초고온 열과 황-요오드 공정을 통해 수소를 생산하는 핵심 기기이다. 한국원자력연구원에서는 초고온가스로에 사용될 기기에 대한 성능시험을 위해 헬륨가스루프를 구축하고 공정열교환기 시제품을 제작하였다. 본 연구는 공정열교환기 시제품을 헬륨가스루프에서 시험하기 전에 미리 공정열교환기 시제품의 고온 구조건전성을 평가하기 위한 작업의 일환으로 공정열교환기 시제품에 대한 고온구조해석 모델링, 열해석 및 열팽창해석 결과들을 정리한 것이다. 해석 결과는 공정열교환기 시제품 성능시험 장치 설계에 반영할 것이다.

상용 냉장고에서 반복 하중을 받는 힌지 키트 시스템(HKS)의 신뢰성 설계 연구 (Reliability Design of the Hinge Kit System in Common Refrigerator Under Repetitive Load)

  • 우성우;이종길
    • 대한공업교육학회지
    • /
    • 제33권2호
    • /
    • pp.312-324
    • /
    • 2008
  • 상용 냉장고에서 새로 설계된 힌지 키트 시스템(HKS, Hinge Kit System)을 개선하기 위하여 새로운 강인 방법론을 연구하였다. 이 방법은 결함 모드, 시장에서의 메카니즘, 가속수명시험법(ALT, Accelerated Life Test)을 이용한 다양하게 개선된 HKS의 설계변수 등을 고려한 것이다. 시장에서의 결함 반품 조사와 첫 번째 ALT 시험을 통한 공통적 크랙 부위는 HKS의 하우징 부분에서 일어남을 확인하였다. 냉장고 HKS의 초기 설계 단계에서 간과한 설계 변수는 하우징이었다. 이를 통하여 냉장고의 특정 열린 지지 구조에서 모든 열린 지지 구조로 확산하여 설계 수정하는 계기가 되었다. 두 번째 ALT 시험을 통하여 발견한 파괴와 크랙 부위는 비틀림 축에서 발생하였다. 설계 변수에서 비틀림 축의 동심도를 고려치 않았던 것이 원인이었다. ALT 시험 절차를 통하여 간과한 설계 변수를 수정할 수 있었다. ALT 시험의 결과를 통하여 연간 결함 발생률이 약 0.01%였고 재설계된 HKS의 B1 수명은 10년으로 파악되었다. 본 논문에서 사용된 변수 설계 방법은 결함 제품 검사, 하중 분석, 세 번의 ALT 시험 등이며 이들은 기계 시스템의 강인 설계에 매우 효과적임을 알 수 있었다. 향후 본 연구에서 제시된 방법은 새로운 가전제품의 강인 설계에 적용할 수 있을 것으로 사료된다.

축력과 반복수평력을 받는 격자강판 내진보강벽의 구조거동에 관한 실험적 연구 (An Experimental Study on the Structural Behavior of Steel Grid Shear Wall subjected to Axial Force and Cyclic Lateral Load)

  • 박정우;심기철;박진영;이영학;김희철
    • 한국전산구조공학회논문집
    • /
    • 제25권6호
    • /
    • pp.525-532
    • /
    • 2012
  • 근래에 지어진 건축물의 경우 지진에 대한 안전성을 확보하고 있지만 1983년 개정이전의 건축물은 내진설계가 미반영 되어 있어 지진에 대해 매우 취약하다. 본 연구에서는 내진성능이 부족한 기존 건축물의 지진 발생 시의 안전성 확보를 위한 내진보강 방안으로 격자강판 내진보강벽을 제안한다. 축력과 반복수평력을 받는 성능실험을 수행하였으며, 실험체는 벤치마크 용도로 순수 철근콘크리트 프레임(BM-RC)과 프레임 내부에 격자강판 내진보강벽(SW-RC)을 설치한 2개의 실험체를 제작하여 실험을 수행하였고, 축력과 횡하중 가력을 위하여 500kN용량의 엑츄에이터 2대와 2,000kN용량의 엑츄에이터 1대를 사용하였다. 실험결과를 통해 벤치마크 실험체와 비교하여 강도, 강성, 연성 및 에너지소산능력을 평가하였다.