• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.665-670
• /
• 2001

The purpose of this study is to develop a new type dryer, which is to proceed mixing and drying of wet-materials at the same time and drying process is carried out in a closed system. In this drying system, thermal contact occurs, when a fluidized zone is created by paddle mechanism. Accordingly, wet-materials is dried in a short time without any damage. Also wet-materials could be dried uniformly to low moisture contents. It is suitable to dry a small quantity of multi-kind materials. And drying process is carried out in a closed system, so as for environmental pollution dust not to be emitted into the atmosphere. Accordingly, it could be used to dry not only food and chemical materials, but also environmental pollution materials.

• Journal of Environmental Science International
• /
• v.9 no.6
• /
• pp.511-515
• /
• 2000

The purpose of this experiment is to prepare ethylene propylene diene terpolymer(EPDM)/ acrylonitrile butadiene rubber(NBR) blend which represents good environmental resistant properties including favorable oil and ozone resistance. With incorporation of EPDM, NBR and other ingredients, the rubber and chemical additives were mixed by mechanical method such as Banbury mixer and open 2-roll mill. Then rubber vulcanizates were manufactured by hot press and mechanical properties, oil and ozone resistance of the test specimens were measured. The oil resistance and ozone resistance of EPDM and NBR, respectively, is remarkably improved by blending EPDM with NBR. The optimum results of oil and zone resistant characteristics were obtained at EPDM/NBR(=25/75 wt%) composition ratio.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.1
• /
• pp.84-92
• /
• 2002

On the cold start of LPG engine, as the engine temperature has not reached its equilibrium temperature, liquid LPG could not be changed perfectly gaseous LPG, although it was passed to the vaporizer. Liquid and gas mixed fuel could influence starting ability and exhaust emission characteristics of LPG engine. In this study, the vaporization characteristic of liquid LPG was investigated with a conventional vaporizer and the vaporizer with heat source(glow plug) installed at preheated chamber inlet, by using the visualization methods and engine test. According to visualization result, even if the engine coolant temperature was $14^{\circ}C$, liquid fuel was supplied to primary chamber over 25 seconds without vaporizing from preheated chamber in such a conventional vaporizer. However, the vaporizer with heat source do not correspond with that, scarcely had been trim on glow plug when LPG began to vaporize. The effectiveness of heat source could be verified by application to the conventional LPG engine.

• Journal of the Korea Safety Management & Science
• /
• v.10 no.3
• /
• pp.109-115
• /
• 2008

A burning principle in gasoline engine is the one of being burned, by which a mixer in air and gasoline enters a combustion chamber and causes a spark in the proper timing. This is formed, by which ECU controls the fuel-injection volume and the fuel-injection timing, and determines the performance of engine. The purpose of this study is to test the characteristics on knocking in gasoline engine with the knocking-sensor equipment and to research into the characteristics in knocking while directly controling the optimal igniting timing and the fuel-injection timing through engine ECU. Given controlling ECU by grasping the characteristics in knocking, which becomes the most problem in the engine tuning market, the tuning in a true sense will be formed in gasoline engine.

• Computers and Concrete
• /
• v.25 no.5
• /
• pp.433-445
• /
• 2020

A method is proposed in this paper to estimate the workability of self-compacting concrete (SCC) in different mixing conditions with different mixers and mixing volumes by recording the mixing process based on deep learning (DL). The SCC mixing videos were transformed into a series of image sequences to fit the DL model to predict the SF and VF values of SCC, with four groups in total and approximately thirty thousand image sequence samples. The workability of three groups SCC whose mixing conditions were learned by the DL model, was estimated. One additionally collected group of the SCC whose mixing condition was not learned, was also predicted. The results indicate that whether the SCC mixing condition is included in the training set and learned by the model, the trained model can estimate SCC with different workability effectively at the same time. Our goal to estimate SCC workability in different mixing conditions is achieved.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.1
• /
• pp.110-115
• /
• 2000

A K-band GaAs MMIC receiver module has been developed using 0.15 ${\mu}{\textrm}{m}$ HEMT technology process. It incorporates two front end low noise amplifiers, a double balanced diode mixer, and filters. The RF input frequency ranges 20.1 to 21 GHz and the IF output 1.1 to 2 GHz. Test results show an overall conversion gain of more than 27 dB, and less than a 2.2 dB noise figure. The image-rejection ratio greater than 21 dB has been obtained. The isolation between RF and IF ports is better than 27 dB, and between LO and IF is more than 50 dB.

• Macromolecular Research
• /
• v.15 no.1
• /
• pp.44-50
• /
• 2007

This study investigated the effect of ultrasound irradiation on the blend of poly(lactic acid) (PLA) and poly(butylene adipate-co-terephthalate) (PBAT). The blends of PLA/PBAT(50/50) (PBAT50) were prepared in a melt mixer with an ultrasonic device attached. Thermal, rheological, and mechanical properties, morphology, and biodegradability of the sonicated blends were analysed. The viscosity of the sonicated blends was increased by the ultrasound irradiation owing to the strong interaction. The morphology of the sonicated blends was significantly dependent on the duration o the ultrasound irradiation. For PBAT50, the phase size reduction was maximized when the blends were ultrasonically irradiated for 30 sec. At longer duration of ultrasound irradiation, the PBAT phase underwent flocculation. Measurement of the tensile properties showed an increased breakage tensile stress and an enhanced Young's modulus when the blends were properly irradiated. This improvement was ascribed to better adhesion between the PLA matrix and the PBAT domain and to better dispersion of the PBAT phase. However, the tensile properties were maximized after excessive energy irradiation, which was ascribed to an emulsifying effect leading to coalescence of the PBAT phase. Impact strength was increased to reach a peak with the ultrasound irradiation, and was higher than the untreated sample for all sonicated samples due to the difference of failure mechanism between the tensile test and the impact test.

• Tribology and Lubricants
• /
• v.21 no.2
• /
• pp.53-62
• /
• 2005

In this study a general Galerkin FE lubrication analysis method was utilized to analyze the complex lubrication performance of a spiral groove seal having an additional inner circular groove, which was designed for a chemical process mixer operating at a low speed of the maximum 500 rpm. Equilibrium seal clearance analyses under varying outer pressure revealed that the seal maintains a certain levitation seal clearance under the outer pressure of more than about 1.5 bar, regardless of a rotating speed. Also, under the normal outer pressure of 11 bar, the axial stiffness of the seal was predicted to have a high value of more than 7.0 e + 07 N/m, regardless of a rotating speed and thereby, the seal is expected to maintain a stable thickness of lubrication film under a certain external excitation acting. A seal levitation test rig was designed and constructed. Experimental results at 500 rpm agreed well with analytical predictions and the applied lubrication analysis method was verified.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.605-612
• /
• 2008

The shear wave velocity ($V_s$) has been commonly used to evaluate the dynamic properties of soil. The field $V_s$ probe (FVP) was already developed to assess the shear stiffness of a soft clay. The objective of this study is to investigate the disturbance effects of the FVP due to the penetration. The laboratory tests are conducted in a large-scale consolidometer (calibration chamber). The reconstituted clay is mixed at the water content of 110% using a slurry mixer. The FVP and down-hole test are carried out every 1cm interval to compare the data. In addition, two square rods with transducers are also implemented to get the reference value. The shear waves evaluated by the FVP, dow-hole tests, and reference rods are closely matched. This study suggests that the disturbance effect of the FVP due to the penetration into the soft clay soils is small enough and the $V_s$ evaluated by the FVP reflects well the in-situ characteristics. Furthermore, the combination of the FVP and down-hole test shows the possibility of hybrid equipment.

• KSBB Journal
• /
• v.25 no.1
• /
• pp.73-78
• /
• 2010

In this study, recovering agent was produced with organic sludge and modified peat moss (MPM) in pilot plant mixer to recover oil contaminated soil, and field test of it was estimated using landfarming method. Oil contaminated soil recovering agent was thought to contain more microorganisms than raw waste sludge and was no problem to come onto the market because there were not any items of specified wastes. According to the results of TPH variation with time, it was observed the initial degradation velocity of oil with produced recovering agent was rapid up to 50% after 4 days, remarkably. Because the microorganisms in the organic sludge discharged from chemical plant already acclimated with oil, therefore, it could be estimated initial degradation velocity of recovering agent might be rapid. It was concluded that the oil contaminated soil recovering agent produced in this study have high marketability because of its two aspects on recycling of wastes and initial rapid degradation capacity.