• 한국분무공학회지
• /
• 제14권1호
• /
• pp.8-14
• /
• 2009

This paper present the diesel fuel spray evolution and atomization performance in a multi-hole nozzle in terms of injection rate, spray evolutions, and mean diameter and velocity of droplets in a compression ignition engine. In order to study the effect of split injection on the diesel fuel spray and atomization characteristic in a multi-hole nozzle, the test nozzle that has two-row small orifice with 0.2 mm interval was used. The time based fuel injection rate characteristics was analyzed from the pressure variation generated in a measuring tube. The spray characteristics of a multi-hole nozzle were visualized and measured by spray visualization system and phase Doppler particle analyzer (PDPA) system. It was revealed that the total injected fuel quantities of split injection are smaller than those of single injection condition. In case of injection rate characteristics, the split injection is a little lower than single injection and the peak value of second injection rate is lower than single injection. The spray velocity of split injection is also lower because of short energizing duration and small injection mass. It can not observe the improvement of droplet atomization due to the split injection, however, it enhances the droplet distributions at the early stage of fuel injection.

• 마이크로전자및패키징학회지
• /
• 제13권1호통권38호
• /
• pp.43-49
• /
• 2006

새로운 잔류 기공 추출 공정을 적용하여 Blind via hole(BVH)의 형상에 따라 발생되는 잔류기공 특성, 거동 및 신뢰성평가를 수행하였다. 잔류 기공 추출 공정을 적용한 시편에서는 잔류기공이 완전히 제거 되었으며, 기존 공정으로 제조된 시편에 비하여 40% 수준의 향상된 결과를 나타내었다. BVH의 형상에 관계없이 1.5기압수준으로 약 30초 이상 동안 추출하면 BVH내부의 잔류기공은 제거 되어지며 JEDEC 기준의 신뢰성으로 평가한 결과 BVH내부에 잔류기공은 존재하지 않았다.

• 한국강구조학회 논문집
• /
• 제18권5호
• /
• pp.625-631
• /
• 2006

구조재의 잔류응력(residual stress)은 외부에서 하중이 작용하지 않는 상태에서도 구조물 내부에 존재하는 응력으로 건설현장에서 구조물을 설치, 조립하는 경우에 발생하게 되며 특히 용접이나 과부하에 의한 구조물의 설치 후에도 발생할 수 있다. 이에 본 연구에서는 600MPa급 mega structure용 강관제작 상의 프레스 및 용접에 의한 잔류응력의 영향을 파악하고자 홀드릴링 변형게이지법(Hole-Drilling Strain Gage Method)을 이용하여 용접선 부근을 중심으로 총 59개소를 측정하여 잔류응력의 분포 및 크기를 평가하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 추계학술대회 초록집
• /
• pp.90.2-90.2
• /
• 2011

This paper describes performance enhancement of a fuel cell's blower by controlling flow path. Different duct diameter at the inlet and outlet of the blower is selected for reducing blower noise level and input power. Hole diameter and the number of hole at the check valve are tested to reduce the input power of the blower. Two types of blower, fuel pressurized blower and cathode blower, are considered in the present study. Throughout experimental measurements of the test blowers, it is found that duct diameter is effective to reduce noise level and input power in the fuel cell blower. Noise reduction due to the optimal duct diameter at the outlet is more effective when flow rate is relatively large. That is, cathode blower has larger noise reduction compared to fuel pressurized blower because of larger flower rate. Input power of the blower can be reduced by controlling the hole diameter and the number of hole at the check valve.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.7-12
• /
• 2004

Large-sized pins are usually used to lift and handle large low speed diesel engine crankshaft. There has then been a need to reduce and optimize the weight of the traditionally used pins. Making an hole by cutting the inside of the pin out was investigated in view of static and fracture strength. To compensate the stress increase caused by the introduction of the inner hole, the groove in the circumferential direction pre-existing on the pin is to be removed. Finite element analysis was carried out for both the original model and weight reduced model. Stress intensity factors for semi-elliptical defects assumed on the pin for the original model and weight reduced model was calculated using the ASME method and compared with the fracture toughness test result of the pin material. The diameter of the cutting hole for the revised model was determined based on the analysis results.

• 터널과지하공간
• /
• 제18권4호
• /
• pp.280-288
• /
• 2008

발파진동은 암반 및 인근 구조물에 심각한 문제를 야기할 수 있기 때문에 시공 전 발파진동의 예측과 안전성 평가가 반드시 선행되어야 한다. 최근 발파진동 영향평가를 위하여 시추공이나 시험발파를 통해 획득한 실측진동파형을 이용한 동적수치해석이 증가하고 있다. 하지만 시추공 발파 진동파형은 실제 발파현장에서 측정된 진동파형과 진동수준이나 진동지속시간에서 다소 차이가 있으며 이는 단일공 파형과 유사한 특성을 가진다. 따라서 본 연구에서는 단일공 파형의 중첩모델링을 통해 발파조건 변화에 따른 진동파형을 획득하고 이 파형을 이용한 동적수치해석을 수행하였다.

• 한국항공우주학회지
• /
• 제50권3호
• /
• pp.165-172
• /
• 2022

핀틀 인젝터는 추진제 분사면적 조절이 가능하기 때문에 추력제어에 가장 적합한 인젝터이다. 그에 따라 본 논문에서는 액체산소와 기체메탄을 사용하여 다중 홀 핀틀 인젝터와 연속형 핀틀 인젝터의 연소시험을 수행하였다. 특성속도효율로 두 핀틀의 연소성능을 확인하였고, O/F와 연소실 압력에 따라 두 파라미터가 유사한 조건에서 실험결과를 비교하였다. 개도(산화제 분사면적)가 100% 추력조건일 때 다중 홀 핀틀의 효율이 연속형 핀틀보다 다소 높은 결과를 나타내었다.

• 대한가정학회지
• /
• 제24권2호
• /
• pp.1-11
• /
• 1986

The subject, in the blouses that sleeve caps and sleeve lengthes are different from, did sensory test by right arm movement and both arms movement. This sensory test which is used in fabric good, is Shef's. RESULTS : 1) The ease of bust size is very significant by cap height, at 5%, 1% level by sleeve length. 2) The front area of arm hole is affected by cap height, sleeve length movements more than the back and the under area of arm hole are 3) Sleeve width is affected by cap height, sleeve length both arms movement. That is, they should be designed according to the use because they affect the ease of blouse very much. Especially bust size should be considered with sleeve pattern because the ease bust becomes different with sleeve pattern.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 춘계학술발표대회 논문집
• /
• pp.163-167
• /
• 2001

A two-dimensional progressive failure analysis method is presented for the strength characterization of the composite joints under pin loading. The eight-nodes laminated she]1 element is utilized based on the updated Lagrangian formulation. The criteria by Yamada-Sun, Tsai-Wu, and the maximum stress are used for the failure estimation. The stiffness of failed layer is degraded by the complete unloading method. No factor depending on test is included in the finite element analysis except for the material strength and stiffness. Total 20 plate specimens with and without hole are tested to validate the finite element prediction. The Tsai-Wu failure criterion most conservatively estimates the strength of laminate, and the maximum stress criterion yields the highest strength because it does not consider the coupling of the failure modes. The strength by Yamada-Sun method neglecting the matrix failure effect are located between other two methods and shows best agreement with test result for laminate with hole.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.105-108
• /
• 1995

So far,in deep drilling process there are several manufacturing problems such as hole deviation, hole over size, circularity,straightness and surface roughness. Whit regard to these problems, we atudied the abrasion process on carbided tip of BTA drill and got the follow test results through the abrasion characteristic test and analysis on cutting mechanism for the drill tooth and guide pad. 1) In SM55C drilling process, the most stable and reasonable drilling speed range for optmum abrasion characteristic of drill tooth was 60m.min. 2) The total drilling torque was about 60kg .deg.cm on condition drilling speed 60m/min and 0.15mm/rev. These results show that the theoretical burnising torque is well accord with the tested torque which is working on guide pad.