• 대한기계학회논문집A
• /
• 제25권1호
• /
• pp.61-69
• /
• 2001

EFP(Fitness For Purpose) type defect assessment methodologies based on ECA(Engineering Critical Analysis) have been established and are in use for the structural integrity evaluation of gas pipelines. ECA usually includes the fracture mechanics analysis, and it is assumed that the J-integral uniquely characterizes the crack-tip stress-strain field. However, it has been proven that the J-integral alone can not be sufficient to characterize the crack-tip field under low levels of constraint with a single parameter. Since pipeline structures are made of ductile material, locally loaded in tension, cracks may experience low level of constraint, and therefore, J-dominance will be lost. For this reason, the level of constraint must be quantified to establish a precise assessment procedure for pipeline defects. The objective of this paper is to investigate the fracture behavior of a crack in gas pipeline(KS D 3507) by quantifying the level of constraint. For this purpose, tensile tests and CTOD tests were performed at room temperature(24$\^{C}$) and low temperature(-40$\^{C}$) to obtain the material properties. J-Q analyses were performed for SENB and SENT specimens based on 2-D finite element analyses, in order to investigate the in-plane constraint effects on pipeline defects. For precise assessment of cracks, especially shallow cracks, in KS D 3507 pipeline, constraint effect must be considered.

• 패션비즈니스
• /
• 제8권1호
• /
• pp.141-155
• /
• 2004

Chitosan, the natural biodegradable polymer derived from chitin by de- acetylation, has been widely applied to the textile finishing processes for excellent anti-microbial characteristic and handle improvement of fabric. The purpose of this study is to investigate the change of handle when cotton fabric is treated with chitosan-polyurethane mixed solution. The viscosity values of chitosan solutions were 8cps and 50cps, and the wet-pick-up% was maintained at 90%. In case of mixing with water soluble polyurethane, the mixture ratio of chitosan and polyurethane was settled on the solid content ratio of 1:0, 1:0.5, 1:1, 1:2. Also the change of physical properties by neutralization in NaOH solution was studied. The results can be summarized up as follows : 1. Extensibility(EM) and tensile energy(WT) of cotton fabric treated with chitosan are decreased, but bending rigidity(B) is remarkably increased. With the addition of polyurethane, the decrease of EM and WT is weakened and the increase of B is weakened. The case of neutralization is similar to the case of polyurethane addition. 2. By treating fabric with chitosan, FUKURAMI(Fullness and softness) is decreased, but KOSHI(Stiffness), SHARI(Crispness), HARI(Anti-drape Stiff ness) are increased. With the addition of polyurethane, the decrease of FUKURAMI is diminished and the increase of KOSHI, SHARI, HARI are diminished. 3. As the viscosity of chitosan solution increased, the air permeability value increased. The addition of polyurethane decreased the air permeability.

• 한국도로학회:학술대회논문집
• /
• 한국도로학회 2002년도 학술발표회 논문집
• /
• pp.89-92
• /
• 2002

본 연구의 목적은 여러 가지의 폐자원중 슬래그 및 폐주물사의 도로포장용 골재로서의 특성을 평가하고, 이를 이용한 다양한 조합의 재활용 아스팔트 혼합물의 소성변형 특성을 평가하는 것이다. 골재특성을 평가하기 위해 입도 및 입형분석, 비중 및 흡수성, 마모저항성, 골재안정성과 같은 시험을 수행하였다. 골재로서의 특성평가 시험 결과 고로슬래그는 비교적 강도 특성이 제강슬래그에 비해 작은 경향을 나타냈다. 마샬배합설계로서 최적 아스팔트 함량이 결정되었고, 그 범위는 7.2%에서 7.5%정도 였다. 재활용 골재를 이용한 조합의 아스팔트 혼합물의 소성변형 특성을 평가하기 위해 간접인장강도시험, 회복탄성계수시험, 크리프 시험을 수행하였다. 재활용 골재를 이용한 아스팔트 혼합물의 소성변형 특성이 일반골재를 이용한 아스팔트 혼합물에 비해 다소 떨어지는 경향을 나타내었다. 다만 현재진행중인 휠트래킹 시험 결과가 나오면 재활용 골재를 활용한 아스팔트 혼합물의 소성변형특성을 좀더 구체적으로 파악할 수 있을 것으로 판단된다.

• 한국정밀공학회지
• /
• 제17권12호
• /
• pp.185-194
• /
• 2000

Rapid Prototyping(RP) techniques have their unique characteristics according to the working principles: stair-stepped surface of parts due to layer-by-layer stacking, low build speed caused by line-by-line solidification to build one layer, and additional post processing to improve surface roughness, so it is required very high cost to introduce and to maintain of RP apparatus. The objective of this study is to develop a new RP process, Variable Lamination Manufacturing using linear hotwire cutting technique and expandable polystyrene foam sheet as part material(VLM-S), and to investigate characteristics of part material, cutting characteristics by using linear hotwire cutting system and bonding. Experiments were carried out to investigate mechanical properties of part material such as anisotropy and directional tensile strength. In order to obtain optimal dimensional accuracy, surface roughness, and reduced cutting time, addition experiments were performed to find the relationship between cutting speed and cutting offset of hotwire, and heat generation of hotwire per unit length. So, adhesion strength tests according to ASTM test procedure showed that delamination did not occur at bonded area. Based on the data, a clover-shape was fabricated using unit shape part(USP) it is generated hotwire cutting. The results of present study have been reflected on the enhancement of the VLM-S process and apparatus.

• 한국강구조학회 논문집
• /
• 제24권4호
• /
• pp.443-450
• /
• 2012

이 연구에서는 내진구조용 강재(SN)의 냉강롤성형된 각형강관을 사용한 CFT 부재의 중심축하중에 대한 구조성능을 평가한다. 일반적으로 냉간롤성형 및 냉간프레스형성으로 인하여 각형강관의 코너부와 평판부 모두 SN강재에 비해 재질변화가 발생하며, 항복강도와 인장강도 및 항복비의 상한치가 높아지는 경향을 나타낸다. 이러한 현상은 강관의 국부좌굴 이후의 비선형거동에 의해 영향을 주며, 이는 CFT 합성 부재와 같이 비선형해석모델에 대하여 영향을 미친다. 따라서 각형강관의 가공열화도를 평가하기 위하여 각형강관의 재료시험을 수행하였고, 세장비 및 판-폭두께비를 실험변수로 하여 일축 압축력을 받는 CFT부재의 구조성능을 평가하였다.

• 한국강구조학회 논문집
• /
• 제26권3호
• /
• pp.219-229
• /
• 2014

원형 강관으로 보강된 GFRP 재질의 원통형 쉘구조에 대한 극한 휨 실험 및 범용 유한요소해석 프로그램인 ABAQUS를 사용한 전산해석을 수행하였다. 개인하수처리 시설의 설계 기준에서 제시된 직사각형 단면형상의 GFRP 재질의 보강링이 적용된 설계기준을 바탕으로 원형 강관 보강링에 대한 단면 재료 특성이 반영된 식을 검토하여 설계하였다. 보강링의 단면, GFRP 본체의 직경과 두께에 의한 극한 거동 특성을 분석하기 위하여 총 4개의 시험체를 설계 제작하여 집중하중 정적재하 시험을 수행하였다. 실험결과 강관 보강링이 사용된 GFRP 쉘구조는 휨파괴가 발생할 때까지 충분한 연성도를 가지고 있으며, 강관 보강링의 휨강성 증가에 따른 전체 구조물의 강도증진이 효과적임을 확인하였다.

• 소성∙가공
• /
• 제20권2호
• /
• pp.140-145
• /
• 2011

The aim of the present study is to derive optimized post heat treatment temperatures to get a proper formability for Ti/STS409L/Ti clad materials. These clad materials were fabricated by cold rolling followed by a post heat treatment process for 10 minutes at temperatures ranging from $500^{\circ}C$ to $850^{\circ}C$. The microstructure of the interface was observed using a Scanning Electron Microscope(SEM) and an Energy Dispersive X-ray Analyser(EDX) in order to investigate the effects of post heat treatment on the bonding properties of the Ti/STS409L/Ti clad materials. Diffusion bonding was observed at the interfaces with a diffusion layer thickness increasing with the post heat treatment temperature. The diffusion layer was composed of a type of(${\varepsilon}+{\zeta}$) intermetallic compound containing additional elements, namely, Fe, Ti and Ni. The micro Knoop hardness of the Ti/STS409L interfaces was found to increase with heat treatment up to $800^{\circ}C$ and then decrease for temperatures rising up to $850^{\circ}C$. The tensile strength was shown to decrease for heat treatment temperature increasing to $750^{\circ}C$ and then increase rapidly for temperature rising up to $850^{\circ}C$. A post heat treatment temperature range of $700{\sim}750^{\circ}C$ was found to optimize the formability of Ti/STS409L/Ti clad materials.

• Journal of Welding and Joining
• /
• 제33권2호
• /
• pp.56-61
• /
• 2015

IRW(Inverter Resistance Welding) process and DSW(Delta-spot welding) process for dissimilar materials of DP590 and Al5052 were performed to evaluate the welding quality and mechanical properties. IRW experiment was carried out with changing the welding current. The other welding parameters such as pressure force, weld time, squeezing time and holding time were fixed. On the anther hand, DSW experiment was performed using the process tape at welding current of 11.5kA. The other conditions were same as IRW conditions. The various testes such as shear tensile strength, nugget diameters, EDS, SEM and cross-sectional observation for weld zone was performed. As a result, IMC(Inter Metallic Compound) thickness at 11.5kA was thinner than those of 9.5kA and 10.5kA conditions. In addition, thined IMC layer was observed when high electric current apply to the materials(DP590 and Al5052) in a short time throught dissimilar resistance spot welding controling welding conditions. The relationship between the thickeness of IMC and current intensity was after discussed.

• 펄프종이기술
• /
• 제42권1호
• /
• pp.54-63
• /
• 2010

Recently, as the function of largest supplier of biomass for "low carbon green growth", the necessity for systematic management of afforestation areas is emphasizing. The forestation of seedling, besides the afforestation cost itself, is required some additional follow-up management costs, like mowing and fertilizing of forestation area, and removal of bindweed. The mulching mat for afforestation seedlings is available for rooting of little seedlings as well as initial forestation expenses. Mulching technique is also used to control soil temperature and moisture by covering the surface of ground. In this study, the paper based-mulching film coated with biodegradable polymer and functional additive was specially produced using laboratory bar coater, and analyzed for its degradable behavior. Coating colors were prepared by dissolving PE (polyester) 80 % and PLA(polylactic acid) 20 % in chloroform and finally applied to handsheet prepared by preceding study conditions. Base paper and polymer-coated paper were artificially aged by 2 kinds of degradation methods, which are soil degradation by microorganism and light degradation by 257 nm UV wavelengths. Strength property, oxidation index and morphological property were evaluated by reduction rates of tensile strength, FTIR spectra ratio of carboxyl and carbonyl group and SEM micrograph. As these results, polymer coated-paper was superior to base paper in degradation behaviors, having results with lower reduction rate of strength properties.

• 폴리머
• /
• 제30권4호
• /
• pp.305-310
• /
• 2006

전자선 전조사를 이용하여 PE/PP와 PET 복합섬유 기재에 스티렌을 그래프트 공중합하여 복합양이온 교환 섬유를 합성하였다. 공중합체의 그래프트율은 스티렌 단량체의 농도가 80%일때 123%이었으며 설폰화율은 스티렌 농도 70%에서 3.3 mmol/g 이었으며 그 이후에서는 큰 변화가 없었다. 또한 섬유의 인장강도는 기재에 비해 모두 낮게 나타났으며, 공중합체보다 이온교환 섬유의 인장강도가 최대 $0.206kgf/mm^2$ 로 낮게 나타났다 이온교환 섬유의 칼슘 및 마그네슘 이온에 대한 흡착파과 시간은 pH, 온도가 증가할수록 길어졌으며, 혼합 용액의 경우 단일 용액에 비해 마그네슘의 흡착파과가 늦게 나타났다. 한편 칼슘 및 마그네슘에 대한 반응속도 상수는 각각 0.012, 0.011 L/mg.h 이었으며, 최대 이온교환 흡착용량은 각각 47.06, 42.83 mg/g, 활성화 에너지는 각각 2,169, 1,534 J/mol 이었다.