• Steel and Composite Structures
• /
• 제49권2호
• /
• pp.215-230
• /
• 2023

Cable-girder anchorage joint is the critical part of cable-supported bridges. Tensile-plate anchorage (TPA) is one of the most commonly used types of cable-girder anchorage joints in steel girder cable-supported bridges. In recent years, it has been proposed by bridge designers to apply TPA to concrete girder cable-supported bridges to form composite cable-girder anchorage joint (CCGAJ). In this paper, the mechanical performance of CCGAJ under tensile force is studied through experimental and numerical analyses. Firstly, the effects of the external prestressing (EP) and the bearing plate (BP) on the mechanical performance of CCGAJ were investigated through three tests. Then, finite element model was established for parametrical study, and was verified by the experimental results. Then, the effects of shear connector forms, EP, BP, vertical rebar rate, and perforated rebar rate on the tensile capacity of CCGAJ were investigated through numerical analyses. The results show that the tensile capacity of CCGAJ depends on the first row of PR. The failure mode of CCGAJ using headed stud connectors is to form a shear failure surface at the end of the studs while the failure mode using PBLs is similar to the bending of a deep girder. Finally, based on the strut-and-tie model (STM), a calculation method for CCGAJ tensile capacity was proposed, which has a high accuracy and can be used to calculate the tensile capacity of CCGAJ.

• 한국지반공학회논문집
• /
• 제18권3호
• /
• pp.33-41
• /
• 2002

쏘일네일링 공법은 굴착이나 사면안정을 위해 가시설이나 영구용으로 국내에서 널리 이용되고 있다. 특히, 도심지 근접 굴착시 쏘일네일링 공법 적용시 고려사항은 벽체변위와 네일의 인장등 이다. 본 연구는 국내 여러 암반층을 포함하는 다층토 지반의 11개 쏘일네일링 현장에서 굴착단계별 네일의 인장력 거동을 계측자료와 역해석을 통하여 고찰하였다. 역해석 결과 네일의 최대인장력은 계측값의 50% 정도로 낮게 나타났고, 벽면에서 가상 파괴활동면까지의 거리를 주동영역거리라 할때 CLOUTERRE 보고서와 Cartier & Gigan이 각각 제안한 최종굴착 깊이(H$_{f}$ )의 0.3$H_f$,0.5$H_f$,에 비해 계측결과는 크게 나타났으며, 역해석은 이들이 제안한 범위내에 포함되었다.

• 한국철도학회논문집
• /
• 제11권3호
• /
• pp.280-285
• /
• 2008

Gurson model과 shear failure model 두 가지 파괴모델을 이용하여 노치인장시험과 초기 균열을 가지는 파쇄튜브의 압축거동을 유한요소법으로 해석하였다. Shear failure model의 파라미터 값은 노치인장시편의 시험 및 해석을 통하여 결정하였다. 항복강도와 파괴전단변형률 등의 파라미터 값을 정한 후, Gurson model과 shear failure model을 파쇄튜브의 해석에 적용하였다. Gurson model과 shear failure model이 인장시편에 대하여는 비슷한 파괴 거동을 보여주지만 파쇄튜브의 압축력과 균열 성장 속도에서는 다른 결과를 보임을 확인하였다. 즉, shear failure model에서는 Gurson model에 비하여 균열이 전파되기 위해 더 큰 압축력이 요구되었다. 이러한 현상은 shear failure model 이 재질의 손상 과정에 대한 고려를 포함하고 있지 않기 때문인 것으로 생각된다. 어느 모델이 튜브의 해석에 적당한 지를 실험을 통하여 검증할 필요가 있다.

• Wind and Structures
• /
• 제31권6호
• /
• pp.533-548
• /
• 2020

Despite the current technologic developments, failures in existent tensile fabric structures (TFS) subjected to wind do happen. However, design pressure coefficients are only obtained for large projects. Moreover, studies on TFSs with realistic supporting frames, comparing static and dynamic analyses and discussing the design implications, are lacking. In this study, fluid-Structure analyses of a TFS supported by masts and inclined cables, by subjecting it to different wind speeds, are carried out, to gain more understanding in the above-referred aspects. Wind-induced stresses in the fabric and axial forces in masts and cables are assessed for a hypar by using computational fluid dynamics. Comparisons are carried out versus an equivalent static analysis and also versus loadings deemed representative for design. The procedure includes the so-called form-finding, a finite element formulation for the TFS and the fluid formulation. The selected structure is deemed realistic, since the supporting frame is included and the shape and geometry of the TFS are not uncommon. It is found that by carrying out an equivalent static analysis with the determined pressure coefficients, differences of up to 24% for stresses in the fabric, 5.4% for the compressive force in the masts and 21% for the tensile force in the cables are found with respect to results of the dynamic analysis. If wind loads commonly considered for design are used, significant differences are also found, specially for the reactions at the supporting frame. The results in this study can be used as an aid by designers and researchers.

• 한국공작기계학회논문집
• /
• 제15권4호
• /
• pp.49-55
• /
• 2006

This study deals with the friction welding of SM25C and SCNCrM-2B; The friction time was variable conditions under the conditions of spindle revolution 2,000rpm, friction pressure of 100MPa, upset pressure of l50MPa, and upset time of 4.0 seconds. Under these conditions, the microstructure of weld interface, tensile fracture surface and mechanical tests were studied, and so the results were as follows. 1. When the friction time is 2.0 seconds, the tensile strength of friction welds was 874MPa, which is around as much as 117% of the tensile strength of base metal(SM25C), the bending strength of friction welds was 1,354MPa, which is around as much as 108.9% of the bending strength of base metal(SM25C). 2. At the same condition, the maximum vickers hardness was Hv443 at SCNCrM-2B nearby weld interface, which is higher Hv20 than condition of the friction time 0.5 seconds. 3. The results of microstructure analysis show that the structures of two base materials have fractionated and rearranged along a column due to heating and axial force during friction, which has affected in raising hardness and tensile strength.

• 오토저널
• /
• 제10권3호
• /
• pp.38-44
• /
• 1988

It is important to control the axial forces of high tension bolts such as the automobile, construction machine, aircraft, marine engine bolts. However, the direct method to measure the axial forces of bolts practically have not been found out. The ultrasonic techniques is based on the principles that the bolt tensile elongation and ultrasonic velocity changes are proportional to the axial force below the yield point of the materials. From the result of the experiment, the coefficient of acoustoelasticity k could be measured as - 11.18*10$_{-5}$m $m^{2}$k $g_{f}$./.

• Structural Engineering and Mechanics
• /
• 제42권2호
• /
• pp.191-210
• /
• 2012

The Force Density Method (FDM) is a well known and extremely versatile tool in form finding of cable nets. In its linear formulation such method makes it possible to find all the possible equilibrium configurations of a net of cables having a certain given connectivity and given boundary conditions on the nodes. Each singular configuration corresponds to an assumed force density distribution. Its improvement as Non-Linear Force Density Method (NLFDM) introduces the possibility of imposing assigned relative distances among the nodes, the tensile level in the elements and/or their initial undeformed length. In this paper an Extended Force Density Method (EFDM) is proposed, which makes it possible to set conditions in terms of given fixed nodal reactions or, in other words, to fix the positions of a certain number of nodes and, at the same time, to impose the intensity of the reaction force. Through such extension, the (EFDM) enables us to deal with form findings problems of cable nets subjected to given constraints and, in particular, with mixed structures, made of cables and struts. The efficiency and the robustness of method are assessed through comparisons with other form finding techniques in dealing with characteristic applications to the prestress design of cable systems. As a further extension, the EFDM is applied to structures having some parts not yet geometrically defined, as can happen in designing new creative forms.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2002년도 학술.기술논문발표회
• /
• pp.37-41
• /
• 2002

Lap splice is used in building construction up to recently. As buildings become higher and larger, the use of high tensile bar is increasing due to increasing in the use of high compression concrete. However the using of high tensile bar in lap splice causes eccentricity and difficulty in placing of concrete inside the form, therefore not allowing enough intervening material. Various mechanical connection are being developed but the coupler of today needs either a secondary intervening material or secondary processing that consumes much time. Therefore a coupler, needing neither a secondary intervening material nor secondary processing, was made in this study which lead to following results. (1) Breaking occurred in all experimented rebar. (2) Acquirement of tension exceeding the standard requirement. (3) Acquirement of elongation percentage within the standard requirement.

• 한국생산제조학회지
• /
• 제20권4호
• /
• pp.490-494
• /
• 2011

In this paper, using by rapid heating and cooling systems for injection molding and temperatures to changes. In the process of molding temperature and pressure inside the mold was found. In addition, the tensile strength of test specimens were molded, mechanical properties of injection molded parts were identified on mold temperature. Copper could withstand more tensile force than NAK. Therefore, it can be concluded that materials with high heat conductivity must be used in thin walled products.

• Journal of Welding and Joining
• /
• 제21권2호
• /
• pp.70-75
• /
• 2003

Spot welding is a process that sheet metals are joined in one or more spot by heating at the faying interface. In this process, the spatter is dispersed from melted area. It has been reported that spatter generation has adverse effects on weld quality. However, no systematic study has been carried out to find out its effect on weld quality in resistance spot welding processes. In this study, specially designed specimen are used to perform experimental investigation of spatter generation and its effect. Major finding of this study show trends in tensile-shear strength for various amounts of spatter generated during spot welding process. Thus, optimum welding conditions are proposed in view of spatter generation and tensile-shear strength. (Received December 11, 2002)