• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 1999년도 추계학술발표대회 논문집
• /
• pp.160-163
• /
• 1999

The mechanical properties and failure behaviour of carbon/phenolic composites were inverstigated by tension and compression. Carbon/phenolic composites were fabricated by infiltration of matrix into 8 harness satin woven fabric of PAN-based carbon fibers. The tensile and compressive tests were performed at 25℃ under air atmosphere and, at 400℃ and 700℃ under N₂ atmosphere. The tensile strengths of carbon/phenolic composites in with-laminar/0° warp direction were about 10 times higher than those in with-laminar/45° warp direction, which was analyzed due to a change of fracture mode from fiber pull-out by shear to tensile fracture of fibers. The fracture of carbon/phenolic composites in with-laminar/45° direction was analyzed due to delamination by buckling. Tensile and compressive strength of carbon/phenolic composites decreased to about 50% at 400℃, and to about 10% at 700℃ compared to that at room temperature. The main reason for the decrease of tensile or compressive strength with increasing temperature was analyzed due to a reduction of bond strength between fibers and matrix resulting from thermal degradation of phenolic resin.

• Structural Engineering and Mechanics
• /
• 제20권5호
• /
• pp.589-608
• /
• 2005

There is a growing need for the development and implementation of new methods for the rapid and cost-effective rehabilitation of deteriorating steel structural components to offset the drawbacks related to welding and/or bolting in the field. Carbon fiber reinforced polymer (CFRP) composites provide a potential alternative as externally bonded patches for strengthening and repair of metallic structural members for building and bridge systems. This paper describes results of an investigation of tensile and fatigue response of steel/CFRP joints simulating scenarios of strengthening and crack-patching. It is shown that appropriately designed schemes, even when fabricated with levels of inaccuracy as could be expected in the field, can provide significant strain relief and load transfer capability. A simplified elasto-plastic closed form solution for stress analysis is presented, and validated experimentally. It is shown that the bond development length remains constant in the linear range, whereas it increases as the adhesive is deformed plastically. Fatigue resistance is shown to be at least comparable with the requirements for welded cover plates without attendant decreases in stiffness and strength.

• 펄프종이기술
• /
• 제30권2호
• /
• pp.55-61
• /
• 1998

This treatment was applied to bleached softwood kraft pulp handsheets in an effort to improve physical strength of paper. Paper strength was improved by esterification of cellulose and polycarboxylic acid. Because hydrogen bond of carboxyl group is stronger than that of hydroxyl group, polycarboxylic acid forms stronger hydrogen bond than cellulose does. 1,2,3,4,-cyclopentanetetracarboxylic acid (CPTA) and sodium dihydrogen phosphate ($NaH_2O_4$) were used as polycarboxylic acid and catalyst, respectively This reaction was confirmed by the weight gain of the handsheets, by FTIR spectrum and by changes in mechanical properties of sheets. Wet tensile strength was improved when handsheets were treated with polycarboxylic acid. However, tear strength and burst strength decreased.

• 대한소아치과학회지
• /
• 제29권3호
• /
• pp.389-396
• /
• 2002

이 연구의 목적은 전형적인 우식제거(bur)와 기계화학적으로 제거된 상아질($Carisolv^{TM}$)의 microtensile bonding strength를 비교하는 것이다. 다음과 같은 결합 system이 사용되었다; AB: All Bond 2(3M, USA), PB: Prime & Bond 2.1(Dentsply, DE), AQ: AQ Bond(sun medical, Japan). 교합면 우식증을 가지고 있는 42개의 사람 대구치를 6개 그룹으로 나누었다. 각각의 그룹은 다음과 같이 나누었다; $Carisolv^{TM}$를 적용한 그룹 A, B, C와 bur를 사용한 그룹 D, E, F, A와 D 그룹에서는 AB가 상아질 결합제로 사용하였고, 그룹 B, E는 PB를 그룹 C, F는 AQ를 사용하였다. 그 후 와동은 복합레진(Z-100)으로 충전하였다. 각각의 시편을 0.7 mm 두께로 자르고 0.7 mm의 넓이로 다시 잘랐다. Microtensile bonding strength test는 $0.5\;mm/min^{-1}$의 crosshead에서 시행하여 파절면을 scanning electron microscope(JSM-6400, Jeol, Japan)로 관찰하여 다음과 같은 결과를 얻었다. 1. $Carisolv^{TM}$로 우식을 제거했을 때 Microtensile bonding strength는 bur를 사용한 것에 비해서 75.8-80%로 감소하였다(p<0.05). 2. $Carisolv^{TM}$로 우식을 제거했을 때 Microtensile bonding strength가 감소된 정도는 상아질 결합제의 종류에 따라 각 군별로 차이가 없었다(p<0.05). 3. $Carisolv^{TM}$로 우식을 제거했을 때 All bonds는 32.6 MPa, Prime & bond는 30.1 Mpa, AQ bond는 21.2 Mpa이었다. 4. Bur와 $Carisolv^{TM}$로 우식제거시 AQ bond는 All bond와 Prime & bond 2.1보다 유의하게 낮은 결합강도를 가졌다(p<0.01).

• Restorative Dentistry and Endodontics
• /
• 제7권1호
• /
• pp.77-83
• /
• 1981

The purpose of this study was to observe the bonding strength between tooth surface (enamel and dentin) and restorative filling materials which are two composite resins (Clearfil and Concise) and Glass ionomer cement, after etching with 50% phoshoric acid and 37% citric acid. To measure the bonding strength in enamel, the labial surface of upper anterior tooth was cut flatly with using carborundum disk and polished with sand paper disk, and to measure in dentin, the dentin surface was prepared by grinding upper part of posterior tooth horizontally. After washing the tooth surface with water and drying with air blast, the prepared tooth surface was etched. In glass ionomer cement, 50% phosphoric acid and 37% citric acid were used, in Clearfil 40% phosphoric acid was used and in Concise, 50% phosphoric acid and 37% citric acid were used as etchant for 1 minute. After the copper band which is 5 mm in diameter and 5 mm in height was fixed on the prepared surface and each filling material was inserted into the copper band, the hooking loop was inserted into filled material in the copper band before setting to make it easily that the load is applied on the specimen. After all specimens were immersed in water at $37^{\circ}C$ for 1 week, this specimen was placed on the load cell of tensile test apparatus, and specimen was pulled at the cross-head speed of 0.8 mm per minute. The following results were obtained 1) In glass ionomer cement, the bond strength obtained by 37% citric acid was higher than one obtained by 50% phosphoric acid in enamel and dentin surfaces. The bond strength obtained in non-etched surface was much less than one by etchants in enamel and dentin surface. 2) In Clearfil, the bond strength obtained by 40% phosphoric acid was 4 times more than one obtained by non etch ant. 3) In Concise, the bond strength obtained by 50% phosphoric acid was almost same as one obtained by 37% citric acid, and the bond strength obtained by non etch ant was much less than one obtained by etchants.

• 콘크리트학회논문집
• /
• 제13권5호
• /
• pp.499-506
• /
• 2001

본 연구는 8개의 직접인장실험을 수행하여 축방향 부재의 콘크리트강도에 따른 부착특성과 균열거동을 조사하였다. 주변수는 콘크리트강도로 보통강도 24-25 MPa, 고강도 61-63 MPa이다. 직접인장시험체는 2종류로서 짧은 시험체는 횡균열 사이의 인장부재를 모형화하였고, 긴 시험체는 다수의 횡균열이 발생하는 인장부재를 모형화하였다. 이러한 직접인장실험을 수행하여 다음과 같은 결론을 얻었다. 부착강도는 압축강도에 비례하여 증가한다. 그러므로 고강도콘크리트에서 응력교란구간의 길이는 더 짧아지고 횡균열 간격이 더 줄어든다. 콘크리트강도가 25MPa에서 61MPa으로 증가하였지만 쪼갬균열하중은 거의 같게 나타났다. 반면에 횡균열하중은 인장강도에 비례하여 증가하였다. 따라서 고강도콘크리트를 사용할 때에 현행 구조설계기준의 정착길이 산정방법은 재고될 필요가 있고, 피복두께와 순철근간격을 더 크게 하든지 횡보강철근의 의무화하는 것이 현행 기준에 추가되기를 권장한다.

• 대한소아치과학회지
• /
• 제46권2호
• /
• pp.127-134
• /
• 2019

이 연구의 목적은 지르코니아 기성관에 대한 교정용 밴드의 접착제로서 컴포머 시멘트와 레진 시멘트를 평가하고자 하였다. 총 30개의 시편을 준비하였다. 상악 우측 제 2유구치의 스테인리스 스틸 기성관에 컴포머 시멘트로 교정용 밴드를 접착한 I군과 지르코니아 기성관에 컴포머 시멘트로 밴드를 접착한 II군, 지르코니아 기성관에 레진 시멘트로 밴드를 접착한 III군으로 나누었고 밴드의 결합력을 측정하기 위해 인장력을 가하였다. I군, II군과 III군의 결합력의 평균값은 각각 0.79 MPa, 1.09 MPa 그리고 1.56 MPa였다. II군이 I군보다 유의하게 높은 결합력을 보였고, II군과 III군 의 결합력에는 유의한 차이가 없었다. 컴포머 시멘트와 기능성 단량체를 포함한 레진 시멘트는 유구치 지르코니아 기성관에 대한 교정용 밴드의 시멘트로서 양호한 결합력을 보였다.

• 한국공작기계학회논문집
• /
• 제14권5호
• /
• pp.62-73
• /
• 2005

The objects of this research are to establish the criteria of peel occurrence considering the shape of bond terminus and to compare the strength properties of adhesive joint of different three type such as butt joint, T-shape, and single lap Joints. The criteria of peel occurrence at the bond terminus was suggested. Peel loads of three type adhesive joint (butt Joint, T-shape specimen, single lap joint) were determined from tensile tests. Principal stress distributions of these joints were determined from finite element method analysis. Then, peel occurrence was estimated with stress singularity factor$(K_{prin})$ when the terminus shape was square, with average principal stress when the terminus shape was rounded. The conclusions are summarized as follows; (1) In the non-filleted model(e.g., butt joint, T-shape specimen), principal stress shows singularity at the bond terminus, intensity of stress(principal stress) singularity $(K_{prin})$ can use as the criteria of peel occurrence at the bond terminus. (2) In the filleted model(e.g., single lap joint), principal stress has not affected singularity at the bond terminus. Average principal stress$(K_{av})$ can use as the criteria of peel occurrence at the bond terminus.

• 구강회복응용과학지
• /
• 제16권2호
• /
• pp.113-122
• /
• 2000

The reinforced composte resin as the esthetic operative material continuously has been studied because the porcelain fused metal prosthesis is widely used for its excellent esthetics, rigidity and marginal integrity, but it has low fracture resistance against the tensile strength and stress, attrition of the opposite teeth. The reinforced composite resin is well adapt with the dental alloy but it is low the shear bond strength with the dental alloy vs the porcelain fused metal prosthesis, and then has been studied continuously. The purpose of the study was to examine how metal was the higher shear bond strength among the dental alloy was used to the reinforced composite resin and to find the effect that the particle size of sandblasting influenced the shear bond strength. We built up the reinforced composite resin with 4 mm in diameter, 3 mm in height on circular alloy with 5 mm in diameter, 2 mm in height. Type II gold, type IV gold, and Ag-Pd alloy was used as alloys and $50{\mu}m$, $110{\mu}m$, $250{\mu}m$ of the particle size was sandblasted at each alloy in bonding between alloy and resin. We made 90 secimens of 10 per each group and we measured the shear bond strength using the Instron($M100EC^{(R)}$, Mecmesin Co., England). The obtained results were as follows : 1. In comparison among each alloys, Ag-Pd alloy had the highest shear bond strength and the shear bond strength was decreased significantly in the sequence of the type II gold and type IV gold(P<0.001). 2. In comparison according to the size of sandblasting particle, (1) In Ag-Pd alloy, shear bond strength was decreased in the sequence of $110{\mu}m$, $250{\mu}m$, $50{\mu}m$ and there were significant difference in all the group. (P<0.05) (2) In type II gold, it was decreased in the sequence of $250{\mu}m$, $50{\mu}m$, $110{\mu}m$ and there were significant difference. (P<0.05) (3) In type IV gold, it was decreased in the sequence of $110{\mu}m$, $50{\mu}m$, $250{\mu}m$. There were significant difference between the group of $110{\mu}m$ and $50{\mu}m$, the group of $110{\mu}m$ and 250, but there were no significant difference in the group of $50{\mu}m$ and $250{\mu}m$. 3. The highest shear bond strength according to the size of sandblasting particle was $110{\mu}m$ in Ag-Pd alloy and type IV gold, $250{\mu}m$ in type II gold.

• Restorative Dentistry and Endodontics
• /
• 제21권2호
• /
• pp.602-618
• /
• 1996

The purpose of this study was to investigate the effect of acid treatment of fluoride applied dentin surface with various concentrations of phosphoric acid for various periods of time on dentin bonding. Dentin specimens prepared from freshly extracted bovine mandibular anterior teeth were divided into fluoridated and nonfluoridated groups. Specimens of nonfluoridated group were pretreated with 10% phosphoric acid for 15 seconds. Those of fluoridated groups were treated with 2% sodium fluoride or 2% stannous fluoride solution for 5 minutes and stored in $37^{\circ}C$ distilled water for 3 days, followed by phosphoric acid treatment. The concentrations of phosphoric acid were 10%, 32% or 50% and the treatment periods of time were 15, 30 or 60 seconds. All the specimens were bonded with All Bond$^{(R)}$ 2 and Bisfil$^{TM}$ composite resin. After bonded specimens were stored in $37^{\circ}C$ distilled water for 24 hours, tensile bond strengths of each specimens were measured and the pretreated dentin and the fractured dentin surfaces were examined under the scanning electron microscope. The results were as follows : The tensile bond strengths from the fluoridated groups were significantly lower than those from the nonfluoridated group when the concentrations of phosphoric acid and the treatment periods of time were equal in all the groups (p<0.05). In general, the higher the concentration of phosphoric acid and the longer the treatment period of time for acid etching on the fluoride applied dentin surface, the higher were the bond strength values. Recovery of bond strength of the dentin bonding agent was better in the NaF applied group than in the $SnF_2$ applied one. SEM findings of NaF applied and $SnF_2$ applied dentin surfaces demonstrated reaction product-covered and partially or completely obstructed dentinal tubules. SEM findings of dentin surfaces fluoridated for 5 minutes followed by etching showed wider tubular openings and more clean dentin surfaces when dentin was etched with higher concentration of phosphoric acid for longer period of time. On the SEM observations of the fractured dentin-resin interface, the etched specimens of fluoridated group showed an adhesive failure mode when the concentration of phosphoric acid and the treatment period of time were same as in the nonfluoridated group. As the concentration of phosphoric acid and the treatment period of time increase during acid etching, the cohesive failure area increased. However, excessive acid etching caused adhesive failure.