• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2021년도 봄 학술논문 발표대회
• /
• pp.181-182
• /
• 2021

Selecting a proper tile cement for ceramic tile is important to secure tile construction quality. But there is some ambiguity in standards about evaluating adhesion test such as using KS L 1593 in Lab test but using KS L 1592 in site. So, this study aims to how to select proper tile cement for securing adhesion strength in site considering both tensile and shear adhesion strength of cement for ceramic tile. Also, when doing tensile adhesion test in site, there may be adhesion drop because of cutting tile with grinder. As a result, drop of adhesion strength is about 9% ans quality manager consider these factor and should select proper tile cement.

• 대한건축학회논문집:구조계
• /
• 제35권11호
• /
• pp.147-154
• /
• 2019

The purpose of this study is to evaluate the effect of admixtures as blast-furnace slag(BF) and fly ash(FA) on tensile and adhesive properties of polymer cement mortar(PCM) with EVA emulsion. The test specimens are prepared with five polymer-cement ratio(P/C) and five admixture contents, and tested for tensile strength and adhesion in tension. From the test results, the tensile strength and adhesion in tension could be improved by an appropriate combination of P/C and admixture contents. In particular, the maximum of tensile strength of PCM with P/C 10% and BF content of 10% is 4.70MPa which is about 1.55 times higher than that of plain mortar, and about 1.22 times that of PCM that does not contain any mixture. The ratio of adhesion in tension to tensile strength of PCM with admixtures averaged 55.8%. It is also apparent that admixture contents of 5% or 10% could be proposed for improvement of tensile strength and adhesion in tension of PCM.

• Journal of the Korean Wood Science and Technology
• /
• 제25권3호
• /
• pp.16-23
• /
• 1997

This study was carried out to discuss feasibility of high density polyethylene(HDPE) as a new substitute for the conventional adhesives in plywood manufacture. Plywood was composed of radiata pine(Pinus radiata) and Malas(Homallium feotidium) veneers and bonded by HDPE. Adhesion characteristics and anatomical scanning has been examined through tensile-shear strength test and scanning electron microscopy(SEM). The results are as follows; 1. Optimum loading quantity was 15g/$(30.3{\times}30.3)cm^2$, and tensile-shear strength increased with the increase of loading quantity. 2. Even at the hot pressing time of 1 minute, tensile-shear strength met the value of KS(over the 7.5kgf/$cm^2$), and tensile-shear strength increased with the increase of hot pressing time. 3. Plywood composed of veneer at moisture content of 19.6% showed similar tensile-shear strength to that at air conditioned moisture content of 11.4%. 4. Under the same condition of hot pressing time, tensile-shear strength of plywood bonded by HDPE met the KS value of boil and wet test and proved the same group as phenol formaldehyde adhesive. 5. HDPE films showed mechanical adhesion through penetration into the lathe check and ray of veneer.

• 한국도로학회논문집
• /
• 제11권3호
• /
• pp.33-40
• /
• 2009

폐타이어 고무분말은 도로 유지 및 보수제로 아스팔트 바인더의 개질제로 사용되고 있다. 도로보수제인 폐타이어 고무분말 개질 아스팔트 (crumb rubber modified asphalt, CRMA) 실란트에 필요한 접착특성은 저온에서 아스팔트 바인더의 취성과 접착파괴특성 때문에 주목받고 있다. 본 연구에서는 저온에서 CRMAs의 개질제로서 유연제의 영향을 조사하였다. 저온에서 CRMAs의 특성은 침입도, 연화점, 인장 및 인장접착시험을 통하여 측정하였다. 유연제를 도입한 CRMAs에서 CR과 아스팔트바인더의 연성변형이 증가함에 따라 인장접착강도와 변형률이 증가하였다. 저온영역에서 CRMAs의 인장특성과 접착특성은 유연제의 함량이 중요한 요소임을 발견하였다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2016년도 춘계 학술논문 발표대회
• /
• pp.217-218
• /
• 2016

Sheet based waterproofing methods are factory produced and have a advantage or forming uniform waterproofing layer in construction sites, allowing them to become a commonly used material domestically. Particularly in the case of EVA waterproofing sheets, they can be manufacturing using recycled materials and are thus increasing in application due to their eco-friendly factors. However, heating adhesion method has to be used in case of overlapping areas of waterproofing sheets, but not enough studies have been made on the adhesion stability based on different heat adhesion speed. In this paper, EVA sheets have been studied with their overlap area properties following a heat adhesion method in wintertime ambient conditions and have been observed for the changes in the tensile strength based on different head adhesion speed and rates. According to the results, 6~7m/min adhesion speed was shown to have produce the best tensile strength.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 가을학술발표대회논문집
• /
• pp.107-108
• /
• 2023

In this study, the tensile adhesion strength was evaluated according to KS F 4932 to assess the suitability of MMA-based repair materials for concrete roads. Two types of MMA were used. Mortar mock-ups were made and tested for adhesion strength in three different surface conditions: air, water, and salt water. Both showed strengths above the standardized strength of 0.6 MPa. Type B, which has a relatively low adhesion strength, is considered more suitable.

• 한국환경과학회지
• /
• 제23권11호
• /
• pp.1909-1918
• /
• 2014

In this experiment no solvent based polyurethane(PU) adhesives were prepared with the polyol, isocyanate, dioctyl phthalate(DOP), 2-hydroxyethylacrylate(2-HEA) and other acrylate monomers. The softenening point of the PU adhesives measured by Ring & Ball method were examined in the present study. And adhesion strength and mechanical properties such as tensile strength and 100% modulus of the PU adhesives were evaluated by Universal Test Machine. The experimental results showed that increase of both DPE-41, benzoylperoxide(BPO) and toluene diisocyanate(TDI) increased softenening point, adhesion strength, tensile strength and 100% modulus. However as DOP content increased sofenening point, adhesion strength decreased and tensile strength, 100% modulus also decreased.

• 접착 및 계면
• /
• 제25권1호
• /
• pp.162-168
• /
• 2024

The effect of maleinized polybutadiene (MPB) on the mechanical properties of epoxy resins including adhesion strength, elongation and impact peel resistance was investigated in this study, in which MPB is an anhydride-functionalized polybutadiene prepolymer. Different molecular weights (3.1K and 5.6K) of MPB were added to diglycidyl ether bisphenol-A (DEGBA), an epoxy resin, to increase its impact peel strength and elongation. At various loading percent (5, 10, 15, 20 and 25 wt%) of MPB in the epoxy resin, significant improvements of mechanical properties were observed. According to the comparative analysis results, the modified epoxy system with 15 wt% (3.1K) MPB exhibited the highest lap shear strength, about 40% higher than that of neat epoxy. The tensile strength and elongation steadily and simultaneously increased as the loading percent of MPB increased. The impact peel strengths at low (-40℃) and room (23℃) temperatures were substantially improved by MPB incorporation into epoxy resins. Reactive and flexible MPB prepolymer seems to construct strong nano-structured networks with rigid epoxy backbones without sacrificing the tensile and adhesion strengths while increasing impact resistance/toughness and elongation properties. For higher impact peel while maintaining adhesion and tensile strengths, approximately 10-15 wt% MPB loading in epoxy resin was suggested. Consequently, incorporation of functionalized MPB prepolymer into epoxy system is an easy and efficient way for improving some crucial mechanical properties of epoxy resins.

• 한국건축시공학회지
• /
• 제19권6호
• /
• pp.485-494
• /
• 2019

본 연구는 고로슬래그 미분말 및 플라이애쉬를 혼입한 SAE 에멀젼 기반 폴리머 시멘트 모르타르의 휨과 인장특성에 대하여 실험하여 혼화재의 혼입효과를 평가하고자 하였다. PCM은 폴리머 시멘트비와 혼화재의 혼입율을 변화시켜 시험편을 제작하였으며, 휨강도, 휨접착강도, 인장강도 및 인장접착강도 시험을 실시하였다. 연구결과, 혼화재의 혼입에 따른 휨강도 및 휨접착강도 개선은 거의 발현되지 않았으나, 인장강도 및 인장접착강도에서는 혼화재의 혼입에 따른 강도개선 효과를 얻을 수 있었다. 특히 PCM의 인장 접착강도는 P/C 20%, 고로슬래그 미분말 혼입율 10%에서 최대 3.35MPa로 보통시멘트 모르타르의 약 2.36배, 혼화재를 혼입하지 않은 PCM의 약 1.32배의 높은 강도를 나타냈으며 인장접착강도/인장강도비는 평균 48.7%를 나타냈다. 본 연구를 통하여 PCM의 인장 및 인장접착강도 개선을 위해서는 혼화재 혼입율 5% 또는 10%를 제안할 수 있었다.

• 한국건축시공학회지
• /
• 제2권3호
• /
• pp.131-138
• /
• 2002

The objective of the study is to examine the characteristic correlations between reinforcing carbon fiber and interfacial adhesion agent since the interfacial adhesion strength between reinforcing carbon fiber and matrices is believed to be an essential element influencing the physical properties in carbon fiber reinforced cement composite using slurry method. The integrity of interfacial adhesion between reinforcing fiber and cement not only affects the quality of fiber reinforced cement composite but also influences to a large degree the physical properties of the cement composite when producing carbon fiber reinforced cement composite using slurry method. Having analyzed the physical properties 1.e., water content, tensile strength, flexural strength and flexural toughness of carbon fiber reinforced cement composite specimens, C-PAM(cation polyacrylamide) was determined to be an optimum interfacial adhesion agent. The study has also demonstrated that interfacial adhesion strength varies largely on the content and type of the reinforcing fiber. Judging from magnified view of the tensile shear cross-section using VMS(video microscope system), interfacial adhesion strength between reinforcing fiber and matrices is affected by the type of interfacial adhesion agent. According to the result of the experiments, C-PAM was determined to be an ideal interfacial adhesion agent when using carbon fiber in producing carbon fiber reinforced cement composite with the optimum content of carbon fiber being established.