• Journal of Korean Society for Atmospheric Environment
• /
• v.6 no.2
• /
• pp.168-175
• /
• 1990

Pasquill stability class (PSC) was evaluated with Monin-Obukhov length (L) using the data observed at a height of 213m meteorological tower in Tsukuba, Japan. PSC was determined with wind speed and insolation (net radiation at night), and L was calculated with the heat flux and the friction velocity obtained at 25m by the eddy correlation method. To evaluate PSC with L, for every class of Pasquill stability (from A to F class), percentiles and median of L were used. Results show that for every class of Pasquill stability, L varies so widely that PSC does not adequately represent the atmospheric stability conditions. The scheme which estimates L using air temperature at two levels and wind speed at single level was developed. Comparison between estimated L by the scheme and observed L reveals that the scheme is better than PSC. Furthermore, the scheme is more advantageous than PSC because it uses air temperature at two levels instead of insolation which is more difficult to observe in the field than air temperature.

• Korean Journal of Metals and Materials
• /
• v.50 no.7
• /
• pp.495-502
• /
• 2012

The aim of this study was to analyze high temperature deformation stability and properties of duplex stainless steels(DSS) according to annealing temperature. In order to analyze high temperature deformation stability, a number of compression tests were carried out with a stain rate of $10^{-2}s^{-1}{\sim}10s^{-1}$ up to a compression ratio of 50% in a temperature range of $950^{\circ}C-1300^{\circ}C$. The analysis of high temperature deformation stability of DSS was performed based on the Ziegler model. In order to analyze the high temperature properties of DSS, annealing treatments were conducted by isothermal holding for 1 hr at $950^{\circ}C$ to $1300^{\circ}C$ with $50^{\circ}C$ intervals followed by water cooling. The hardness and tensile tests were performed on specimens with different volume fractions of constituent phases, such as austenite, ferrite and sigma. The hardness and tensile strength of 2507 according to the annealing temperature are better than those of 2205. The strain rate sensitivity and Ziegler parameter are higher in 2205 than in 2507 as a whole, which implies that 2205 is better than 2507 in terms of forgeability at high temperature.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.4 no.3
• /
• pp.172-176
• /
• 2003

In this paper, we studied the effects of mold temperature on the microstructure of injection molded parts. The weld line decreases in length and width as mold temperature increases. We investigated the dimensional stability of the parts made of two kinds of resin(polypropylene and polystyrene) by varying the mold temperature. As the mold temperature is high, both the shrinkage ratio and the thickness difference for the PS parts decreases. But the observation of PP parts shows a tendency to increase. The easiness of cavity filling and transcription of the mold texture is improved as the mold temperature is high.

• YAKHAK HOEJI
• /
• v.43 no.6
• /
• pp.793-797
• /
• 1999

Salmonella typhi Ty21a is an attenuated strain of S. typhimurium and used for oral typhoid vaccine. In an attempt to increase the stability of Ty21a manufacturing typhoid vaccine, we studied about the stability of freeze-dried Th21a including additives at various temperature conditions. In order to investigate the freeze-drying rate of Ty21a according to various absorbance, we lyophilized Ty21a by using 8% sucrose as a stabilizer. The optimal freeze-drying rate of Ty21a was appeared when OD (optical density) value of the growth was between 2.5 and 3.0. To investigate the stability of Ty21a at various temperature, the viability was measured after storaging the freeze-dried Ty21a at the room temperature, cold and freezing condition for 1 week. The viability of Ty21a in cold and freezing storage condition was 5 times more stable than in room temperature. To search the most stable additives for the freeze-dried Ty21a, the viability of Ty21a including additives at the various storage condition was estimated. Mannitol and loctose were the most stable additives. Theses results suggest that the OD value of Ty21a growth, low temperature, mannitol and lactose are important factors for the optimal freeze-drying rate, the stable storage and the most stable additives, respectively.

• Journal of the Korean Society of Safety
• /
• v.34 no.4
• /
• pp.32-40
• /
• 2019

During the manufacturing process of a printed circuit board(PCB), fumes and mists are generated as the ink dries on the PCB surface. The generated fumes and mists are deposited in the dryer wall and the exhaust duct. Deposited fumes and mists may present a fire hazard if the dryer temperature control system fails. In this study, the thermal stability of the fumes and mists deposited in the dryer and ducts has been analyzed by experimental methods such as thermo gravimetric analysis (TGA), differential scanning calorimetry (DSC), auto ignition temperature (AIT), and multiple mode calorimetry(MMC). According to the experimental analyses, experimental samples are likely to generate gas at the temperature ($180{\sim}240^{\circ}C$) that deviates from the normal operating temperature ($150{\sim}156^{\circ}C$). It has been shown that the thermal stability is degraded when the temperature is deviated from the normal operating temperature. In the end, engineering and management safety measures of accidental prevention have been suggested.

• International Journal of Automotive Technology
• /
• v.8 no.4
• /
• pp.395-402
• /
• 2007

Homogeneous Charge Compression Ignition (HCCI) shows great potential for low $NO_x$ emission but is hampered by the problem of no direct method to control the combustion process. Therefore, HCCI combustion becomes unstable easily, especially at lower and higher engine load. This paper presents a method to achieve diesel-fueled HCCI combustion, which involves directly injecting diesel fuel into the cylinder before the piston arrives at top dead center in the exhaust stroke and adjusting the valve overlap duration to trap more high temperature residual gas in the cylinder. The combustion stability of diesel-fueled HCCI combustion and the effects of engine load, speed, and valve overlap on it are the main points of investigation. The results show that: diesel-fueled HCCI combustion has two-stage heat release rate (low temperature and high temperature heat release) and very low $NO_x$ emission, combustion stability of the HCCI engine is worse at lower load because of misfire and at higher load because of knock, the increase in engine speed aids combustion stability at lower load because the heat loss is reduced, and increasing negative valve overlap can increase in-cylinder temperature which aids combustion stability at lower load but harms it at higher load.

• Proceedings of the KIEE Conference
• /
• 1999.11d
• /
• pp.885-887
• /
• 1999

The piezoelectric ceramic resonator using length extensional vibration rather than contour extensional vibration in terms of the size is suitable for personal portable communication. In this paper, $Pb(Zr_{x}Ti_{l-x})O_{3}$ + r[wt%]$Cr_{2}O_{3}$ ceramics, x=0.56, 0.53, 0.50 (ie, Zr/Ti ratios = 56 /44, 53/47, 50/50) r=0, 0.3[wt %], were fabricated. Temperature stability of length extensional vibration mode of those specimens was investigated. Both crystal structure with rhombohedral phase in the case of no addition of $Cr_{2}O_{3}$ and crystal structure with morphotrophic phase boundary in case of additions of 0.3[wt %]$Cr_{2}O_{3}$ had the vest temperature stability and improved temperature stability through thermal aging.

• Korean Journal of Clinical Laboratory Science
• /
• v.46 no.4
• /
• pp.111-116
• /
• 2014

The stability of 21 routine biochemistry analytes was evaluated from the specimens which had been stored under three different temperature conditions for 30 days. Most of the 17 analytes showed significant change, however, the specimens under lower temperature showed more stability than those under higher temperature. Glucose, Albumin, ${\gamma}$-glutamyl transferase, HDL cholesterol analytes were stable over 30 days under $22^{\circ}C$, $4^{\circ}C$, and $-66^{\circ}C$ conditions. This study might be helpful in interpreting the results reflecting the rate of change when inadequate specimens are measured.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.881-884
• /
• 2000

Recently mobile communication fields need piezoelectric ceramic resonators and filters as possible as small. The length-extensional vibration mode of a rectangular piezoelectric cesamic plate has the advantage of the small size, but the mode has not been studied sufficiently because it was not used extensively until now. In this paper, PZT + x[wt%l $Cr_20_3$ ceramics with rhombohedra1 phase were fabricated. And temperature stability for the mode of the ceramic specimen was investigated. Contrary to our expectations, addition of the stabilizer, $Cr_20_3$ did not promote the temperature stability for the mode in the PZT ceramic specimen with rhombohedra1 phase.

• The Journal of Korean Society of Virology
• /
• v.26 no.2
• /
• pp.245-249
• /
• 1996

Hantaan virus vaccine was developed in 1988 and proved effective. This vaccine is a kind of inactivated vaccine, stable for two years when stored at $2-8^{\circ}C$. Almost virus vaccines including Hantaan virus vaccine are produced and kept in fluid state, and the immumogenicity can be easily destroyed at room temperature or at higher temperature. Therefore the vaccines should be kept in the refrigerator to maintain the immunogenicity. In this study, glucose and/or lactose was added as a stabilizer into Hantaan virus vaccine to increase the stability and dried in vaccum with ethanol treatment. 5% glucose and or lactose in Hantaan virus vaccine most effectively increased the stability of vaccine and maintained the immunogenicity at least for three months at room temperature. But drying with ethanol treatment did not help increasing the stability. These results suggest that glucose and lactose could be good stabilizer of virus vaccines.