• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표논문집(II)
• /
• pp.324-329
• /
• 1998

Recently the use of the underwater concrete with the antiwashout admixture is increased considerably. When we intend to apply it to the field, we must consider the water temperature effect. In this study, we investigate the properties of setting time, early strength, hydration temperature history and core strength with the antiwashout underwater concrete in the water temperature 8$^{\circ}C$, 14$^{\circ}C$ and 22$^{\circ}C$ respectively. As a result of experiment, as the water temperature is decreasing, setting time is delayed twice of three times and early strength is lower from 10% to 50%. Therefore to compensate the decrease of the early strength, we used the accelerator and investigated the concrete properties.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.37-41
• /
• 2002

Thermal characteristics of hydrostatic guideway is largely depended on the temperature of supplied oil. For improving the positioning accuracy of hydrostatic guideway, relationship between setting temperature of oil cooler and thermal characteristics is analyzed, and influence of thermal characteristics on positioning accuracy is also analyzed experimental1y in this paper. Laser scale which has 0.01 $\mu\textrm{m}$ of resolution is used as feed-back unit. From the experimental results, it is confirmed that positioning error and repeatability is minimize upto 0.21 $\mu\textrm{m}$ and 0.18 $\mu\textrm{m}$ when the temperature of supplied oil is setting equal to temperature of atmosphere, and also confirmed that thermal deformation, which occurs by the temperature deviation between table and rail or scale supporter, works as limit of repeatability in long time operation.

• 한국산학기술학회논문지
• /
• 제18권1호
• /
• pp.454-459
• /
• 2017

본 논문에서는 최근 매장량의 한계로 인한 화석연료의 가격 상승과 그에 따른 환경적인 문제를 해결하고자 태양광 모듈이 부착된 PTC 집열기 및 3웨이 밸브를 이용한 온열 시스템을 설계 하고자 한다. 온열 시스템은 태양광 모듈이 부착된 태양열 PTC 집열기 사용을 전제로 3웨이 밸브를 이용한 온풍 및 난방 제어 시스템으로써 온도 센서부, 모드 설정부(온풍 및 난방 모드부), 공급부, 온열 시스템 제어부를 포함하여 구성된다. 온도 센서부는 배관 및 실내 온도 표시, 온도 설정부 다중 모니터링 기능이 있으며 모드 설정부는 온풍 및 난방모드 전환, 온풍 및 난방모드 온도 설정 기능을 수행한다. 또한, 온열 시스템 제어부는 PTC 제어 및 온도 설정, PTC 주야 및 시간 선택, 온풍 및 난방 제어, 3웨이 밸브 선택, 등의 기능을 수행한다. 따라서, 태양광 모듈이 부착된 태양열 PTC 집열기 및 3웨이 밸브을 이용한 온열 시스템 설계에 대한 연구 결과 온도 센서부는 $680{\mu}s$, 모드 설정부는 $700{\mu}s$, 온열 시스템 제어부는 $610{\mu}s$의 안정적인 동작 속도로 구동되는 것을 확인 할 수 있었다.

• 한국염색가공학회지
• /
• 제22권2호
• /
• pp.173-179
• /
• 2010

In this study, we determine the stretch and shrinkage properties of conjugated yarns. The shrinkage(%) and elasticity(%) were determined by applying twist conditions of 0, 350, 800, 1000, 1200, 1400, 1600, 2000 T/M (twisting per meter). It is found that the shrinkage(%) and elasticity(%) gradually decreased with increasing T/M. Especially the elasticity(%) dramatically decreased over 1400 T/M condition. In contrast, it is showed that the handle and drapery properties decreased below 1000 T/M, which indicates that the optimal T/M condition could be 1000~1400. The effect of shrinkage(%) and elasticity(%) with different steam setting temperatures (60, 70, 80 and $90^{\circ}C$) was also determined. The shrinkage(%) decreased with increasing setting temperature, while the elasticity not changed. In this context, the optimal steam setting temperature could be $80^{\circ}C$ because it is not easy to weave with the yarns which was set below $80^{\circ}C$. The elasticity(%) decreased with increasing the density of warp and weft. To produce soft handle, excellent drapery and good stretch fabrics, the warp density needs to be reached by 90% of the ideal warp density. In the case of NaOH treatments to the fabrics, the elasticity(%) increased with increasing weight reduction. Therefore, this study have demonstrated that the conjugated yarns with core yarn and the SDY CD(cation dyeable spindraw yarn) as an effect yarn would be appropriate to produce excellent mixture-yarn, which displays clean appearance, good handle and excellent elasticity, The optimized conditions are as follows; 1000~1200 twist per meter, $80^{\circ}C$ steam setting temperature, 90% of ideal warp density and relaxation condition treated with 5g/l NaOH concentration.

• 한국농공학회논문집
• /
• 제53권5호
• /
• pp.25-33
• /
• 2011

In this paper, the effects of aggregate and curing temperature on strength development characteristics of UP (Unsaturated Polyester)-MMA (Methyl Methacrylate) based polymer mortar under sub-zero temperature are experimentally investigated to provide a criterion for repair and production of precast products. The result showed that the setting time of the binder was 4 minutes at $20^{\circ}C$ whereas 35 minutes at $-20^{\circ}C$. The result also revealed that the compressive, flexural, and splitting tensile strengths of UP-MMA based polymer mortar significantly decreased as the aggregate and curing temperatures decreased. However, sufficient strengths which can be implemented in actual practices -36.6 MPa of compressive strength, 6.11 MPa of flexural strength, and 5.81 MPa of splitting tensile strength - were obtained even though both aggregate and curing temperatures were $-20^{\circ}C$. Strength development of polymer mortar is largely affected by curing temperature rather than aggregate temperature. It was found that the effects of aggregate temperature on strength development become smaller as the curing temperature becomes lower. Also, toughness, a ratio of compressive strength to flexural strength, increased from 3.5 to 5.9 as both aggregate and curing temperatures decreased from $20^{\circ}C$ to $-20^{\circ}C$.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2004년도 학술.기술논문발표회
• /
• pp.11-14
• /
• 2004

In this paper, field application of mass concrete using setting time difference of super retarding agent is reported to reduce hydration heat of concrete placed at newly constructed apartment house in Busan. Horizontal placing lift is applied. According to test results. slump and air content meets the requirement of target values. For compressive strength, it exceeds the nominal strength ordered by the costumer. Compressive strength of concrete cured in place is achieved more than the values of nominal strength at l4days. For temperature history, maximum temperature of center at top section shows 58.5$^{\circ}C$, and at bottom section, 62.6$^{\circ}C$. According to naked eye's investigation, no hydration heat crack is observed at the surface of concrete.

• 한국염색가공학회:학술대회논문집
• /
• 한국염색가공학회 2008년도 제38차 학술발표대회
• /
• pp.37-39
• /
• 2008

The purpose of this study is to improve the defects of DPP fabric by heat setting and to describe the change of physical properties of DPP fabrics. The thermosetting was carried out in autoclave from 100 to 140$^{\circ}C$ temperature range for 10min.. In this study, we investigated the effect of the thermosetting temperatures on the structural, thermal, mechanical properties and dyeability of DPP fabrics. The melting peak of multi peak changed to single peak with an increased thermosetting temperatures. The melting energy(J/g), the tensile strength and elongation were found to increase with increasing temperature of heat setting. The diffraction peak at Bragg angle(2${\theta}$) about 13.8$^{\circ}$ were very strong, and diffraction intensity, d-spacing and half-width decreased with increasing thermosetting temperatures. On the other hand, the dyeability(K/S) and crease recovery decreased with an increasing thermosetting temperatures.

• 한국식품영양과학회지
• /
• 제23권3호
• /
• pp.520-529
• /
• 1994

High-ratio cakes made from the formulas with more sugar (140% based on flour weight) than flour have come to be preferred recently. To produced good light cake structure, cake batter must retain the many finely divided gas bubbles formed during mixing . Thermal setting of cake structure is mainly caused by starch gelatinization . The formula controls the temperature at which the cake batter changes from a fluid to a solid. Especially, the relatively large amount of sugar used in the formula delays gelatinization, so that air bubbles can be properly expanded by carbon dioxide gas and water vapor before the cake sets. To get a non collapsing high ratio cake structure after baking , the proper degree of gelatinization of the starch granule, the control of gelatinization temperature, and sufficient gel strength ar all important. The role of ingredients (flour , sugar, proteins, chemical leavening agents, water shortening , and emulsifiers) is reviewed with relation to the formation of satisfactory cake structure.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2005년도 춘계 학술기술논문발표대회 논문집
• /
• pp.21-24
• /
• 2005

In this paper, field application of mass concrete using setting time difference of super retarding agent is reported to reduce hydration heat of concrete placed at newly constructed apartment house in Daejeon. Horizontal placing lift is applied. According to test results,: slump and air content meets the requirement of target values. For compressive strength, it exceeds the nominal strength ordered by the costumer. For temperature history, maximum temperature of center at top section shows $25.6^{\circ}C$, and at bottom section, $35.4^{\circ}C$. According to naked eye's investigation, no hydration heat crack is observed at the surface of concrete.

• Computers and Concrete
• /
• 제3권2_3호
• /
• pp.177-195
• /
• 2006

Slipforming is a construction method in which the forms move continuously during the placement of concrete. This paper presents the development of a computer aided program designated as "CADSLIPFORM" for slipforming operations. The program incorporates maturity methods for the prediction of initial setting times of slipform concrete layers using laboratory data (time-temperature histories and setting times of concrete mixtures at different temperatures) and generates slipform mock-up times. The performance of CADSLIPFORM is validated by comparing simulated mock-up times with those estimated in the field through conventional hard front by rod (R) method. Moreover, the program versatility is demonstrated by illustrating mock-up simulations for different cases with variable slipform parameters such as: number and thickness of concrete layers, concrete temperature (simulating variable setting times) and slipform speed. The program also incorporates the choice of Freiesleben Hansen & Pederson (FHP) and Carino & Tank (CT) maturity functions. CADSLIPFORM can assist user to develop reliable schedule of slipforming operation suitable for a specific project by optimizing various slipform parameters.