• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.4
• /
• pp.430-439
• /
• 2011

In this paper, we design a digital predistortion(DPD) for linearity enhancement of RF power amplifier operating in 900 MHz band. We verify improvement of linearity by comparing the proposed DPD using tanh as a nonlinear indexing function and the DPD using linear indexing function based on signal amplitude. The digital predistortion is realized by look-up table(LUT) method, and the Saleh model is employed for power amplifier modeling, then a commercial power amplifier module is used for measurement. The LUT has 256 tables, and the NLMS(Normalized Least Mean Square) algorithm was utilized for an adaptive algorithm for estimation. As a result, we improve the ACLR(Adjacent Channel Leakage Ratio) by around 15 dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.4
• /
• pp.484-490
• /
• 2012

In this paper, we design a digitally pre-distorted RF power amplifier operating in 900 MHz band. The linearity of RF power amplifier is improved by employing the digital pre-distortion(DPD) based on affine projection(AP) algorithm, where the look-up table(LUT) method is used with non-linear indexing. The proposed DPD with AP algorithm is compared with that with normalized least mean square(NLMS) algorithm, applied to the RF power amplifier. A commercial power amplifier module is used for verification of the proposed algorithm which shows improvement of adjacent channel leakage ratio(ACLR) by about 21 dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.1
• /
• pp.29-36
• /
• 2009

In this paper, the design and implementation of LNA and down-mixer using 90 nm CMOS process are presented for 60 GHz band WPAN receiver. In order to extract characteristics of the transistor used to design each elements under the optimum bias conditions, the S-parameter of the manufactured cascode topology was measured and the effect of the RF pad was removed. Measured results of 3-stages cascode type LNA the gain of 25 dB and noise figure of 7 dB. Balanced type down-mixer with a balun at LO input port shows the conversion gain of 12.5 dB within IF frequency($8.5{\sim}11.5\;GHz$) and input PldB of -7 dBm. The size and power consumption of LNA and down-mixer are $0.8{\times}0.6\;mm^2$, 43 mW and $0.85{\times}0.85\;mm^2$, 1.2 mW, respectively.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.10
• /
• pp.169-177
• /
• 2007

Existing wireless access (mobile) routers are based commonly on the network address and port translation (NAPT) technique which permits simultaneously sharing a subscriber's connection to the network with multiple users. However, the NAPT architecturally makes the users invisible on the network side, thus becoming a user-oriented connection technique. In this paper, we propose a novel service provider-oriented unlicensed nomadic access relay station (WiNNERS) for helping wireless broadband network service providers to make their business more lucrative by accommdating unlicensed band users as subscribers into their network. The WiNNERS offers service providers the capability to directly manage each of the unlicensed band users at the network side. This direct management allows the service providers to flexibly and simply handle QoS, access control, and billing for each user. In order to distinguish each of the unlicensed band users the WiNNERS constructs a virtual tunnel from each user's terminal to the network access router using connection identifiers which is defined for service flow management within the WiBro system, Consequently, our proposed service provider-oriented relay station can be included into the WiBro network system with minimum modifications.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.2762-2767
• /
• 2011

With increasing use of wireless mobile devices like smartphone and tablet PC, telecommunication companies have been providing the internet service by installing a multitude of access points (AP) in subway stations. Most of these APs use frequency of 2.4 GHz band range and the three telecom providers (SKT, KT, LGT) are using the limited channels within this range without any regulations. The channels within 2.4GHz band are already saturated as the companies are setting up wireless AP even within the subway trains for better service. This can affect other 2.4GHz wireless devices used for other purposes with channel interference, etc. This study has tested and analyzed the effects of the wireless APs installed within the subway stations and trains for the internet service on ZigBee-based sensor network for the intelligent surveillance system of urban transit, which is currently being developed and installed.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.9
• /
• pp.63-69
• /
• 2007

The directivity of crossed waveguide directional coupler is generally decreased according as coupling coefficient of it increase. In this paper, the geomertical parameters of crossed slot pair for directivity improvement is modified and the formulas for design of it are proposed. The crossed waveguide directional coupler designed upon the formulas is fabricated with the WR42 waveguide in K-band. The measured results show that the coupling coefficient is 21.5 dB and directivity is minimum 23.9 dB over the operating frequency from 18GHz to 26.5GHz.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.3
• /
• pp.12-24
• /
• 2001

The key advantage of LTCC(low temperature co-fired ceramics) technology is the ability to integrate passive components such as resistors, capacitors, and inductors. More compact circuits with an increased scale of integration are needed with the development for advanced telecommunication system such as IMT-2000. LTCC technology can be obtained by removing these elements from the substrate surface to inside of ceramic body. And it can miniaturize the wireless phone through integration of planar patch antenna, duplexer, band pass filter, bias line, circuit of impedance matching and RF choke etc. Futhermore, with the multilayer chip process and its outstanding electrical material characteristics, LTCC is predestined for highly-integrated, cost effective wide band applications. This paper focuses on the general description of LTCC MCM technologies and the fabrication of the multilayer VCO module.

• Journal of Advanced Navigation Technology
• /
• v.6 no.2
• /
• pp.97-103
• /
• 2002

A recent technology trends in synthetic aperture radar(SAR) requires the ultra high resolution performance in detecting and precisely identifying the targets. In this paper, as a technique for enhancing the radar range resolution, the wide band chirp connection algorithm is presented by stitching the several chirp modules with unit bandwidth based on the linear frequency modulated chirp signal waveform. The principles of the digital chirp signal generation and its architecture for implementation is described with the wide band chirp signal generator, modulator, and demodulator. The performance analysis for the presented algorithm is given with the simulation results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.2
• /
• pp.102-106
• /
• 2008

A new compact UWB bandpass filter with sharp-rejection, low insertion-loss and flat group-delay is developed In this paper, using the transversal filtering combined with SIR(stepped impedance resonator) concept. To form the required passband, multiple out-of-band transmission zeros are created around band-edges, securing very low insertion loss in the very wide frequency range. Also it is found to be beneficial to realize a sharp rejection of higher order with a relatively small overall size and simultaneously have very smoothly varying group-delay which is proper for the UWB applications. The validity of the proposed technique is proven theoretically and experimentally.

• 한국정보통신설비학회:학술대회논문집
• /
• 2006.08a
• /
• pp.193-196
• /
• 2006

In this paper, two $4{\times}4$ rectangular patch array antennas operated at 20 GHz are implemented for the satellite communication. Two $2{\times}2$ sub-arrays are designed and used for the design of $4{\times}4$ patch array. The sixteen patch antennas and microstrip feeding line are printed on the single-layered substrate. The spacing between the array elements is chosen to be $0.736{\lambda}$. The HPBW(Half Power Beam Width) of the $4{\times}4$ microstrip patch array is 17.01 degrees in the E-plane and 17.71 degrees in the H-plane with a gain of 11.6dB in the experimental results. The HPBW of the recessed $4{\times}4$ microstrip patch array is 18.66 degrees in E-plane and 17.12 degrees in the H-plane with a gain of 12.55dB in the experimental results.