• The Journal of the Acoustical Society of Korea
• /
• v.42 no.1
• /
• pp.25-31
• /
• 2023

In order to estimate the radial speed of an underwater object so-called target with active sonar, Continuous Wave (CW) pulse is generally used, but if a target is slow and at near distance, it is not easy to estimate the radial velocity of the target due to acoustic reverberation in the ocean. In 2017, Wang et al. utilized broadband signal of two Hyperbolic Frequency Modulation (HFM) pulses, which is known as a doppler-invariant pulse, with equal frequency band and in opposite sweep directions to overcome this problem and successfully estimate the radial speed of slow-moving nearby target. They demonstrated the estimation of the radial velocity with computer simulation using the parameters of two HFM starting time differences and receiving times. However, for it uses two HFM pulses with equal frequency, cross-correlation between the two pulses negatively affect the detection performance. To mitigate this cross-correlation effect, we suggest using two different band HFM with the opposite sweep directions. In this paper, a method of radial velocity estimation is derived and simulated using two HFM pulses with the pulse length of 1 second and bandwidth of 400 Hz. Applying the suggested method, the radial velocity was estimated with approximately 6 % of relative error in the simulation.

• Asia-pacific Journal of Multimedia Services Convergent with Art, Humanities, and Sociology
• /
• v.7 no.6
• /
• pp.897-906
• /
• 2017

Projection Mapping, also known as Spatial Augmented Reality(SAR) has attracted much attention recently and used for many division, which can augment physical objects with projected various virtual replications. However, conventional approaches towards projection mapping have faced some limitations. Target objects' geometric transformation property does not considered, and movements of flexible objects-like paper are hard to handle, such as folding and bending as natural interaction. Also, precise registration and tracking has been a cumbersome process in the past. While there have been many researches on Projection Mapping on static objects, dynamic projection mapping that can keep tracking of a moving flexible target and aligning the projection at interactive level is still a challenge. Therefore, this paper propose a new method using Unity3D and ARToolkit for high-speed robust tracking and dynamic projection mapping onto non-rigid deforming objects rapidly and interactively. The method consists of four stages, forming cubic bezier surface, process of rendering transformation values, multiple marker recognition and tracking, and webcam real time-lapse imaging. Users can fold, curve, bend and twist to make interaction. This method can achieve three high-quality results. First, the system can detect the strong deformation of objects. Second, it reduces the occlusion error which reduces the misalignment between the target object and the projected video. Lastly, the accuracy and the robustness of this method can make result values to be projected exactly onto the target object in real-time with high-speed and precise transformation tracking.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.758-761
• /
• 2004

This paper proposes a design and implementation of multiplierless digital PID (Proportional-Integral-Derivative) controller using FPGA (Field Programmable Gate Array) for controlling the speed of DC motor in digital system. The multiplierless PID structure is based on Distributed Arithmetic (DA). The DA is an efficient way to compute an inner product using partial products, each can be obtained by using look-up table. The PID controller is designed using MATLAB program to generate a set of coefficients associated with a desired controller characteristics. The controller coefficients are then included in VHDL (Very high speed integrated circuit Hardware Description Language) that implements the PID controller onto FPGA. MATLAB program is used to activate the PID controller, calculate and plot the time response of the control system. In addition, the hardware implementation uses VHDL and synthesis using FLEX10K Altera FPGA as target technology and use MAX+plusII program for overall development. Results in design are shown the speed performance and used area of FPGA. Finally, the experimental results can be shown when compared with the simulation results from MATLAB.

• The Journal of the Acoustical Society of Korea
• /
• v.14 no.4
• /
• pp.5-11
• /
• 1995

In this paper, we design the new high-speed seek algorithm which can access the data of disk (in 3.5-inch optical disk drive). When seek the target track on optical disk in high-speed using the ref-T. E(Reference Tracking Error) and sample pulse signal, it's always possible high-speed seek without re-check and compensation for error by the ref_T. E and sample pulse signal. The performance test result is represented as follow ; it is satify the average seek time of 28mses.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.2
• /
• pp.428-436
• /
• 1998

A TCS slip control system improves acceleration capability and steerability on slippery roads through engine torgue and/or brake torque control. This research mainly deals with the engine control algorithm via the adjustment of the engine throttle angle. The following new control strategy is proposed and investigated ; the TCS slip controller whose input is the difference between the desired driving wheel speed corresponding to the optimum slip ratio and the actual speed yields the target engine torque and then estimates the throttle angle based on the engine performance curve. Various simulation and hardware-in-the-loop simulation have been carried out. The results show the proposed strategy may compensate for the inherent nonlinearity between variation of the throttle angle and variation of the engine torque and produce better performance than the previous strategies without the engine map, especially in the high speed region.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.6
• /
• pp.1010-1017
• /
• 2013

Two-axial electrodynamic forces generated on a conductive plate by a partially shielded magnet wheel are strongly coupled through the rotational speed of the wheel. To control the spatial position of the plate using magnet wheels, the forces should be handled independently. Thus, three methods are proposed in this paper. First, considering that a relative ratio between two forces is independent of the length of the air-gap from the top of the wheel, it is possible to indirectly control the in-plane position of the plate using only the normal forces. In doing so, the control inputs for in-plane motion are converted into the target positions for out-of-plane motion. Second, the tangential direction of the open area of the shield plate and the rotational speed of the wheel become the new control variables. Third, the absolute magnitude of the open area is varied, instead of rotating the open area. The forces are determined simply by using a linear controller, and the relative ratio between the forces creates a unique wheel speed. The above methods were verified experimentally.

• Steel and Composite Structures
• /
• v.19 no.4
• /
• pp.811-827
• /
• 2015

This paper presents a probabilistic investigation of American and European specifications (i.e., AISC and Eurocode 4) for square concrete-filled steel tubular (CFT) stub columns. The study is based on experimental results of 100 axially loaded square CFT stub columns from the literature. By comparing experimental results for ultimate loads with code-predicted column resistances, the uncertainty of resistance models is analyzed and it is found that the modeling uncertainty parameter can be described using random variables of lognormal distribution. Reliability analyses were then performed with/without considering the modeling uncertainty parameter and the safety level of the specifications is evaluated in terms of sufficient and uniform reliability criteria. Results show that: (1) The AISC design code provided slightly conservative results of square CFT stub columns with reliability indices larger than 3.25 and the uniformness of reliability indices is no better because of the quality of the resistance model; (2) The uniformness of reliability indices for the Eurocode 4 was better than that of AISC, but the reliability indices of columns designed following the Eurocode 4 were found to be quite below the target reliability level of Eurocode 4.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.127-131
• /
• 2006

There are being a lot of studies for achievement of high speed Dehydration, high-strength and Lightweight of washing machine in the latest washing machine business. It is essential that Press-joining Strength of Spin Drum Seaming division is improved .to attain that target. Generally, we are using Mechanical press-joining by Seaming and T.I.G (Tungsten Inert Gas) welding among part joint method. Mechanical press-joining method that is mainly using for Stainless Steel (STS430) Drum have lots of merit that consumption of energy is low more than welding and production costs cut down and generation of the corrosion is solved by removing weld zone defect and materials having different properties are enable to join without special equipment. But, it is difficult to realize joint strength required at high speed operation because joint strength of mechanical press-joining method is low remarkably in comparison with welding. Also, there are a lot of analysis difficulties and very limited research is under way due to the dynamic factor such as multistage plastic working, elastic recovery, residual stress etc. The results of this study show optimal joining condition for mechanical press-joining by performing lots of tensile joining strength test with various specimen under multi-change of important design factor such as seaming width, bead area and bead depth etc.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.57-65
• /
• 1999

This document illustrates the way to control of coiling temperature(CTC) of stip tail part in minimill process. The coiling temperature (CT) is very important fact in hot rolling process because the mechnical properties of strip depend on it. In mini-mill pocess, the speed pattern of rolling is different from that of conventional hot rolling. We have a lot of difficulties in controlling the coiling temperature at strip tail part, because after the strip tail is passed out the final stand, it's impossible to control the coiling temperature by using coiling speed. So we have CT deveiation in this gauge, about 160$^{\circ}C$ below in comparison with target CT. It's clear that deviation of mechanical properties(tensile strength, vield ratio etc) of strip to direction of length is so large, so we could not produce middle carbon steel, like this temperature condition. New coiling temperature control of strip especially in strip tail was developed. An innovative method for calculate the deceleration speed of strip tail has been implemented in CTC program, so called

• Journal of the Korean Professional Engineers Association
• /
• v.27 no.2
• /
• pp.42-54
• /
• 1994

Nowadays communication network is steadily changing from a main body of telephone to a network which is creating new services such as multimedia etc. Jhis article introduces a bud of new service and new network which are able to sustain the above service. Including Korea, world advanced countries have been digitatizing their network with N-ISDN (narrowband ISDN) by e.g. 64K b/s and 1.5M b/s. New service by N-ISDN are extraordinary, though it can not solve all kinds of services. To solve these problems, a solving platform should be constituted. B-ISDN(broadband ISDN), as a platform has to be built to deal with almost all uinds of services, whatever the communication speed, communication mode or communication quality may be. Korea Telecommunication Authority(KTA) opened the narrowband ISDN(N-ISDN) at the end of 1993. This was one step previous opening of the broadband ISDN(B-ISDN) service scheduled to be rendered in 2001. B-ISDN, receiving and transmitting by far more information with high speed than the N-NSDN does, is one of G-7 Progects which the Korean government is driving foreward to raise the national scientific power to seven advan ced countries. This is also linked with an extremely high speed information network scheduled to be built by the Ministry of Communications in 2015.