• 한국군사과학기술학회지
• /
• 제20권3호
• /
• pp.352-361
• /
• 2017

This paper proposes a design and fabrication of the test equipment that is implemented as a part of the airborne tracking radar inspection under the environment of indoor simulation. This test equipment provides controlling the operation status of airborne tracking radar and replicating the velocity and range information of target by generating a variety of target signal. This is mainly composed of radar operation controller, target signal generator, horn antenna driving devices. Radar operation controller is able to perform the controlling of radar operation mode and monitoring in real time by serial communication. Target signal generator is generated doppler signal and range delayed signal using virtual target of RF-band. Horn antenna driving devices perform a role of target simulating exercise. In the end, the performance is demonstrated using experiment results of test equipment for airborne tracking radar.

• 한국안전학회지
• /
• 제24권3호
• /
• pp.65-70
• /
• 2009

In-vehicle route guidance information(RGI) systems have been developed with the advancement of the information and communication technologies. However, the RGI is provided by a pre-determined option, drivers occasionally pass the target intersection owing to non- or late- recognizing it. The purpose of this experiment is to examine the position of driver's tum signal operation and intersection recognition approaching at the target intersection which is difficult to identify as a preliminary research on developing the additional RGI connecting with the tum signal control. The field experiment was conducted to measure distances of the turn signal operation and intersection recognition from the target intersection according to driving lanes and landmarks at adjacent intersection. And, glance behavior to the car navigation display was evaluated by using an eye camera. The results indicate that drivers operate the turn signal after confirming a landmark in the case of the intersection with it. However, most case of driving, drivers operate the tum signal at 40 to 50m before coming to the target. To provide the additional RGI, when drivers do not operate the tum signal approaching at the target intersection based on the results, is expected to improve the traffic safety and the comfort for drivers.

• 대한안전경영과학회지
• /
• 제13권4호
• /
• pp.193-199
• /
• 2011

In the past annual recycling obligation rate calculation of Extended Producer Responsibility (EPR) system, it was difficult to operate the system efficiently, because responsible producers passively participated in the scheme only bent on achieving annual obligation without long-term plan. Thus, a new scheme of long-term recycling obligation rate began to be established every five year from 2008 in order to give the basis for the notice of annual specific operation standard and recycling obligation, thereby helping responsible producers to make a preparation with a plan and giving expectation of active operation of the scheme. However, in the operation of long-term recycling target program, while the development of prediction models and the evaluation for existing items has been conducted in various ways, applications for a new target items and the evaluation are quite insufficient. Therefore, in this study, problems in implementing long-term recycling goal of new target items will be examined, and more objective and rational long-term recycling rate calculation and the operation standard will be proposed. Thus, the long-term recycling target will play a role as a pacemaker to steadily improve the recycling performance of target items, and responsible producers will be expected to increase the achievement with the realistic capacity.

• 한국산업정보학회논문지
• /
• 제18권4호
• /
• pp.53-60
• /
• 2013

본 논문에서는 소형표적의 검출속도를 개선하기 위하여, SAD 알고리즘을 이용한 소형표적 검출 방법을 제안한다. 먼저 미디언 필터를 사용해서 클러터를 제거한다. 다음으로 다양한 크기의 구조 요소를 이용해 닫힘 연산과 열림 연산을 수행하고, 닫힘 연산 결과와 열림 연산 결과를 차 연산 하여 표적 후보 화소를 추출한다. 정확한 소형 표적을 검출하기 위해 표적 후보 영역에서 가우시안 거리 함수를 이용하여 표적을 검출한다. 검출 속도를 개선하기 위하여 다음 7프레임에서는 표적의 방향성을 예측한 후, SAD알고리즘을 이용해서 표적을 검출한다. 제안한 방법은 예측된 영역에서만 표적을 추출함으로써 97%의 검출율을 나타내며, 실시간 처리가 가능한 장점을 가지고 있다.

• 전기학회논문지
• /
• 제58권4호
• /
• pp.671-678
• /
• 2009

This paper presents target operation voltage guidelines of each voltage control area considering both voltage stability and economical efficiency in real power system. EMS(Energy Management System) data, Real-time simulator, shows not only voltage level but lots of information about real power system. Also this paper performs optimal power flow calculation of three objective functions to propose the best target operation voltage. objective function of interchange power flow maximum and active power loss minimization stand for economical efficiency index and reactive power reserve maximum objective unction represents stability index. Then through simulation result using optimazation technique, the most effective objective function is chosen. To sum up, this paper divides voltage control area into twelve considering electric distance characteristics and estimate or voltage level by the passage of time of EMS peak data. And through optimization technique target operation voltage of each voltage control area is estimated and compare heir result. Then it is proposed that the best scenario to keep up voltage stability and maximize economical efficiency in real power system.

• 한국산업정보학회논문지
• /
• 제17권4호
• /
• pp.61-70
• /
• 2012

본 논문에서는 모폴로지 연산을 기반으로 소형 표적 후보를 찾고, 변형된 가우시안 거리 함수를 이용해서 소형 표적을 검출하는 방법을 제안한다. 기존의 소형 표적 검출 방법은 예측 필터를 이용하는 방법과 모폴로지를 이용하는 방법이 있다. 예측필터를 이용하는 방법의 경우 최소 오차 수렴 시간이 오래 걸리고, 모폴로지를 이용하는 방법의 경우 클러터에 취약하고, 소형 표적의 크기를 고려하여 구조요소의 크기를 선정해야 하는 단점이 있다. 본 논문에서는 기존 연구 방법의 단점을 보완한 강인한 소형 표적 검출 방법을 제안한다. 제안하는 방법은 먼저 미디언 필터를 사용해서 클러터를 제거한다. 다음으로 다양한 크기의 구조 요소를 이용해 닫힘 연산과 열림 연산을 수행하고, 닫힘 연산 결과와 열림 연산 결과를 차 연산 하여 표적 후보 화소를 구한다. 정확한 소형 표적을 검출하기 위해 표적 후보 영역에서 가우시안 거리 함수를 이용하여 표적을 검출한다. 제안한 방법은 클러터에 민감하지 않고, 98%의 검출율을 보였다.

• 한국군사과학기술학회지
• /
• 제23권3호
• /
• pp.204-212
• /
• 2020

For general target tracking works by receiving a set of measurements from sensor. However, if the SNR(Signal to Noise Ratio) is low due to small RCS(Radar Cross Section), caused by remote small targets, the target's information can be lost during signal processing. TBD(Track Before Detect) is an algorithm that performs target tracking without threshold for detection. That is, all sensor data is sent to the tracking system, which prevents the loss of the target's information by thresholding the signal intensity. On the other hand, using all sensor data inevitably leads to computational problems that can severely limit the application. In this paper, we propose an iterative Joint Integrated Probabilistic Data Association as a practical target tracking technique suitable for a low SNR multi-target environment with real time operation capability, and verify its performance through simulation studies.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2004년도 춘계 학술대회논문집
• /
• pp.208-213
• /
• 2004

The HANARO, multi-purpose research reactor, 30 MWth open-tank-in- pool type, is under normal operation since it reached the initial critical in February 1995. The HANARO is planning to produce a fission moly-99 of radio isotopes, a mother nuclide of Tc-99m, a medical isotope and is under developing a target handling tool for loading and unloading it in a circular flow tube (OR-5). A guide tube is extended from the reactor core to the top of the reactor chimney for easily un/loading a target under the reactor normal operation. But active coolant through the core can be quickly raised up to the top of the chimney through the guide tube by jet flow. This paper is described an analytical analysis to calculate the hole size of a orifice inserted in the circular irradiation hole and to study the flow characteristics through the guide tube under reactor normal operation and loading the target. As results, the results show that the hole size of orifice was 31 mm of the inner diameter to suppress the guide tube jet flow and the coolant safely cooled the target of fission moly after inserting the orifice to the flow tube.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2004년도 춘계 학술대회논문집
• /
• pp.214-219
• /
• 2004

The HANARO, a multi-purpose research reactor of 30 MWth, open-tank-in-pool type, has been under normal operation since its initial criticality in February, 1995. The HANARO is composed of inlet plenum, grid plate, core channel with flow tubes and chimney. The reactor core channel is located at about twelve m (12 m) depth of the reactor pool and cold by the upward flow that the coolant enters the lower inlet of the plenum, rises up through the grid plate and the core channel and exit through the outlet of chimney. A guide tube is extended from the reactor core to the top of the reactor chimney for easily un/loading a target under the reactor normal operation. But active coolant through the core can be Quickly raised up to the top of the chimney through the guide tube by jet flow. This paper is described an analytical analysis to study the flow behavior through the guide tube under reactor normal operation and unloading the target. As results, it was conformed through the analysis results that the flow rate, about fourteen kilogram per second (14 kg/s) suppressed the guide tube jet and met the design cooling flow rate in a circular flow tube, and that the fission moly target cooling flow rate met the minimum flow rate to cool the target.

• 대한방사선기술학회지:방사선기술과학
• /
• 제39권4호
• /
• pp.643-649
• /
• 2016

사이클로트론을 이용하여 $^{18}F^-$동위원소를 생산하는 경우 가속된 양성자 빔은 사이클로트론의 금속부품들과 반응하여 방사화를 일으킨다. 그 중에서도 빔과 주요하게 반응하는 표적집합체를 구성하는 표적실, 표적창에 장반감기의 핵종이 많이 발생한다. 이러한 표적집합체의 방사화 핵종을 잘 이해하는 것은 사이클로트론 운영자와 유지 보수 작업자를 위해서 매우 중요하다. 본 연구에서는 IBA(Ion Beam Application)사 사이클로트론 Cyclone 18/9 기기의 표적집합체 유지보수 작업자의 방사선 안전지침을 마련하기 위해서 사이클로트론 가동 후 표적집합체에 발생되는 주요 핵종을 분석하고, 또한, 사이클로트론 가동정지 직후부터의 선량감소율을 실험적으로 측정하였다. $^{18}F^-$동위원소 생산 후 표적집합체의 잔류 방사화 핵종의 종류 및 방사능농도를 확인하기 위하여, 표적실내 잔류물질 및 표적창 하버포일 시료를 채취하여 고순도 게르마늄(HPGe) 감마핵종분석기로 측정하여 분석하였다. 또한, 사이클로트론 가동직후 사이클로트론에서 발생되는 선량률을 시간에 따라 측정하였다. 감마핵종분석과 선량률감소에 대한 데이터는 추후 사이클로트론 운영의 방사선안전을 위한 데이터로 활용될 수 있을 것으로 기대된다.