• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.10
• /
• pp.1044-1051
• /
• 2003

In this paper, a compact planar microwave duplexer on the high dielectric substrate is presented. As the Ba(Mg$\sub$1/3/Ta$\sub$2/3/)O$_3$(BMT) has good dielectric performances with a high dielectric constant of $\varepsilon$$\sub$r/=23, it is suitable to apply to a printed circuit board fur reducing its circuit size. The BMT substrate is fabricated by using a tape casting fabrication process, and circuit patterns are screen-printed on it by suing silver paste. The open-loop ring type duplexer is designed and implemented on the BMT substrate, and it achieves the smaller size by 80% than one on a commercial substrate($\varepsilon$$\sub$r/=6.15) without degenerating its performance. Therefore the proposed BMT substrate has provided the miniaturization of the duplexer, moreover it can make a contribution towards reducing the size of microwave passive circuits.

• Journal of the Korean Ceramic Society
• /
• v.38 no.9
• /
• pp.860-865
• /
• 2001

After manufacturing 2mol% CdO substitute $0.05Pb(Mn_{1/3}Sb_{2/3})O_3-0.95Pb(Zr_{0.52}Ti_{0.48})O_3$ piezoelectric ceramics powder as starting material, to manufacture green sheets using Doctor Blade method. The optimum composition of slurry was studied. Moreover, the sintering properties and the dielectric and piezoelectric properties with variation a thickness of the manufactured sheets were investigated. The optimum of slurry was investigated by the rheology with addition of additives, the sintering condition was decided by TGA. And the properties of sheet were investigated through SEM. XRD. The optimum of slurry was the stablest at dispersant 3.0 wt% to solid loading 30vol%. After, at addition of binder/plasticizer(0.75/0.25) 3.0wt%, viscosity was 7.55Pa${\cdot}$s. The dielectric and piezoelectric properties of the sheet were increased a little with the increasing of sintering temperature but were not variable with variation of sheet thickness.

• Journal of the Korean Ceramic Society
• /
• v.55 no.5
• /
• pp.492-497
• /
• 2018

This paper reports the efficacy of tape casting using an Ag-10 wt% CuO filler for the successful joining of a sintered $Ce_{0.9}Gd_{0.1}O_{2-{\delta}}-La_{0.7}Sr_{0.3}MnO_{3{\pm}{\delta}}$ (GDC-LSM) ceramic with a SUS 460 FC metal alloy by reactive air brazing. The as-prepared green tape was highly flexible without drying cracks, and the handling was easy when used as a filler material for reactive air brazing. Heat treatment for the GDC-LSM/SUS 460 FC joint was performed at $1050^{\circ}C$ for 30 min in air. Microstructural observations indicated a reliable and compact joining. The room temperature mechanical shear strength of the as-brazed joints was $60{\pm}8MPa$ with a cohesive failure. The flexural strength of joints was measured from room temperature up to $850^{\circ}C$, where the strength retention revealed to be almost 100% at $500^{\circ}C$. However, the joints showed a degradation in strengths at 800 and $850^{\circ}C$, exhibiting strength retentions of 57% and 37%, respectively.

• Journal of the Korean Ceramic Society
• /
• v.34 no.12
• /
• pp.1205-1212
• /
• 1997

The matrices which consisted of SiC whisker, PES(polyesterasulfone) as a binder, span 80(sorbitan monooleate) as a surfactant, TPP(triphenyl phosphate) as a plasticizer and dichloromethane as a solvent, have been prepared by the various methods such as tape casting, rolling, tape cast-coating and roll-coating method. The fuel cells of single stack type using these matrices are characterized by ac impedance spectroscopy and cyclic voltammetry technique. A fuel cell using a matrix prepared by the tape cast-coating method shows the best performance of 466.34 mA/$\textrm{cm}^2$ at 0.6V because it has the lowest polarization resistance at the interface between electrodes and a matrix due to the largest three phase contact region of gases, catalyst and electrolyte.

• Journal of the Korean Ceramic Society
• /
• v.37 no.8
• /
• pp.824-831
• /
• 2000

Alumina tapes, having various ratios of alumina to alumina＋binder＋plasticizer (a/(a＋o)) and binder to binder＋plasticizer(b/(b＋p)), were prepared by the tape casting method. The tapes were thermocompressed varying the thermocompression parameters such as temperature, pressure, and duration time. Among the parameters, the pressure was the most influential to the tape packing density. The packing density varied in two different ways depending on the a/(a＋o) ratio. For the tapes having low a/(a＋o) ratio, a saturation density was reached by applying very a low pressure of 1 MPa. For tapes with high a/(a＋o), on the contrary, the saturation density was obtained at a relatively high pressure. These different responses to the pressure are attributed to the fact that the rearrangement of alumina particles by the pressure becomes easy as an organic content in the tapes is high.

• Proceedings of the Korean Fiber Society Conference
• /
• 2007.11a
• /
• pp.209-210
• /
• 2007

• Proceedings of the Korean Ceranic Society Conference
• /
• 2000.10a
• /
• pp.99.2-99
• /
• 2000

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.850-850
• /
• 2006

• Proceedings of the Korean Ceranic Society Conference
• /
• 2002.10a
• /
• pp.66.2-66
• /
• 2002

• Proceedings of the Korean Ceranic Society Conference
• /
• 2002.10a
• /
• pp.68.1-68
• /
• 2002