• 한국유체기계학회 논문집
• /
• 제8권4호
• /
• pp.20-26
• /
• 2005

When the pumps are started or stopped for the operation or tripped due to the power failure, the hydraulic transients occur as a result of the sudden change in velocity. The field tests on the waterhammer were carried out for Pangyo booster pumping station in which had six booster pumps and two in-line pumps with the motor of output 1,700 kW, respectively. The booster pumping station was equipped with the pump control valve as the main surge suppression device, and the surge relief valve as auxiliary one. But the pump control valve had not early controlled in the planned closing mode, the slamming occurred to the valve of which abruptly closed during the large reverse flow. Because the positive pressure wave caused by the pump failure was superposed on the slam surge, the upsurge increased so extremely that the pump control valve was damaged. After the air chambers were additionally installed in the booster pumping station, it was preyed that the water supply system acquire the safety and reliability on the pressure surge.

• Journal of Welding and Joining
• /
• 제19권1호
• /
• pp.27-32
• /
• 2001

This paper is studied about welding conditions and weldability of seam welding for galvanized steel sheet of automotive. The fuel tank of automobile is made by seam welding to be required of airtight or oiltight. This method have required a short time for welding, simplicity operation progress and little HAZ. Especially, it has more less residual stress and transformation than different welding progress. So, this study is for decreasing the leakage occurrence rate and to make standard operating condition table anyone can operate easily. Therefore, this study is analyzed the optimum conditions of seam welding for making the automobile with galvanized steel sheets by means of observing the microstructure and configuration back projection, RT, tensile-shear strengths test and SEM. Optimum conditions of seam welding obtained as follows, current 17.2-17.6kA speed 1.0m/min weld time 4:10:6 and current 16.5-17.4kA, speed 0.83m/min, weld time 4:10:4 at t1.0, and current, 18.5-18.9kA, speed 0.8m/min, weld time 4:10:4 and current 16.5-17.4kA, speed 0.68m/mi, weld time 4:10:2 at t1.6.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 추계학술대회 초록집
• /
• pp.175.1-175.1
• /
• 2011

A rotating activated bacillus contactor (RABC) process with a series of aerobic reactors was tested in pilot scale to treat digested liquid from an anaerobic digester treating swine wastewater and sewage sludge. The influent (digested liquid) for the RABC process showed C/N ratios less than 2 as a typical feature of effluent from anaerobic digesters. The pilot process, which consists of three 3 RABC reactors, four aerobic tanks and a sedimentation tank, was operated for 210 days with a hydraulic retention time of 20 days without pH and temperature control. Since the Bacillus-enriched aerobic reactors shows high efficiencies of nitrogen removal at low DO levels less than 1.0 mg/L, they were operated at reduced aeration intensities. With relatively low concentrations of organics in comparison with nitrogen concentrations, the RABC process tested in this study showed stable and high nitrogen and organics removal efficiencies over 80%. The nitrogen removal process tested in this study was proven to be an effective and operation-cost saving (lower aeration) method to remove nitrogen without adding external carbon sources to meet the optimum C/N ratio.

• 한국항공우주학회지
• /
• 제43권11호
• /
• pp.1028-1034
• /
• 2015

발사체에 적용되는 솔레노이드 밸브의 경우 산업용 솔레노이드 밸브에 비해 엄격한 전류 및 무게, 크기 제한 조건을 요구한다. 이러한 제한 조건을 만족하며, 솔레노이드 밸브의 작동을 보장하기 위한 추진제탱크 가압제어용 솔레노이드 밸브 설계를 수행하였다. 극저온 상태에서 솔레노이드 전류 상승을 방지하기 위해 구리와 콘스탄탄 재료를 사용한 새로운 형태의 코일 설계를 적용하였으며, 시제품을 이용한 시험결과 측정된 전류는 설계 규격을 만족하고 있다.

• 항공우주기술
• /
• 제3권1호
• /
• pp.97-102
• /
• 2004

우주비행체의 추진시스템은 주차 궤도에서 임무 궤도도의 진입을 위해 필요한 임펄스 및 궤도에서의 3축 자세제어에 요구되는 적절한 임펄스를 제공하는 역할을 수행한다. 다목적실용위성 2호의 추진시스템은 용접으로 조립된 단일추진제 하이드라진 시스템으로 추력기, 추진제 탱크, 압력변환기, 추진제 필터, 격리밸브 및 충전/배출 밸브 등의 주요부품들로 구성되며, 그 외 각 부품들을 연결해주는 추진제 배관과 열제어 부품들이 추가된다. 이 논문에서는 설계에서부터 조립/시험에 걸친 액체 추진시스템의 개발과정을 서술하였다.

• 한국유체기계학회 논문집
• /
• 제7권1호
• /
• pp.30-35
• /
• 2004

The HANARO, a multi-purpose research reactor of 30 MWth open-tank-in-pool type, has been under normal operation since its initial criticality in February, 1995. Many experiments should be safely performed to activate the utilization of the HANARO. HANARO flow simulation facility is being developed for the endurance test of reactivity control units for extended life time and the verification of structural integrity of those experimental equipments prior to loading in the HANARO. This facility is composed of three major parts; a half-core structure assembly, a flow circulation system and a support system. The flow circulation system is composed of a circulation pump, a core flow piping, a core bypass flow piping and instruments. The system is to be filled with de-mineralized water and the flow should be met the design requirements to simulate a similar flow characteristics in the core channel of the half-core structure assembly to the HANARO. This paper, therefore, presents an analytical analysis to study the flow behavior of the system. Computational flow analysis has been performed for the verification of system pressure variation through the three-dimensional analysis program with the standard $k-{\epsilon}$ turbulence model and for the verification of the structural piping integrity through the finite element method. According to the analysis results, it could be said that the design requirements and the structural piping integrity of the flow circulation system are satisfied.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제11권2호
• /
• pp.980-992
• /
• 2019

This paper describes a model test and numerical simulation of a 750-kW-semi-submersible platform wind turbine under several wind and wave conditions for validation of the numerical simulation model. The semi-submersible platform was designed to support the 750-kW-wind turbine class and operate at a water depth of 50 m. The model tests were performed to estimate the performance characteristics of the wind turbine system in the wide tank of the University of Ulsan. Motions and loads of the wind turbine system under the wind and wave conditions were measured and analyzed. The NREL-FAST code was used to simulate the wind turbine system, and the results were compared with those of the test model. The results demonstrate that the numerical simulation captures noticeably the fully coupled floating wind turbine dynamic responses. Also, the model shows a good stability and small responses during waves, wind, and operation of the 750-kW-floating offshore wind turbine.

• Nuclear Engineering and Technology
• /
• 제48권4호
• /
• pp.893-905
• /
• 2016

Numerous advanced reactor concepts have been proposed to replace light water reactors ever since their establishment as the dominant technology for nuclear energy production. While most designs seek to improve cost competitiveness and safety, the implausibility of doing so with affordable materials or existing nuclear fuel infrastructure reduces the possibility of near-term deployment, especially in developing countries. The organic nuclear concept, first explored in the 1950s, offers an attractive alternative to advanced reactor designs being considered. The advent of high temperature fluids, along with advances in hydrocracking and reforming technologies driven by the oil and gas industries, make the organic concept even more viable today. We present a simple, cost-effective, and safe small modular nuclear reactor for offshore underwater deployment. The core is moderated by graphite, zirconium hydride, and organic fluid while cooled by the organic fluid. The organic coolant enables operation near atmospheric pressure and use of plain carbon steel for the reactor tank and primary coolant piping system. The core is designed to mitigate the coolant degradation seen in early organic reactors. Overall, the design provides a power density of 40 kW/L, while reducing the reactor hull size by 40% compared with a pressurized water reactor while significantly reducing capital plant costs.

• 상하수도학회지
• /
• 제17권4호
• /
• pp.519-527
• /
• 2003

Cake layer in crossflow microfiltration(CFMF) can be reduced by coagulation, enhancing membrane flux. This is because enlarging particle size by coagulation increases shear-induced diffusivity and the back-transport of rejected particles. However it is known that the enlarged particles are disaggregated by the shear force of the pump while passing through it. This study is to look at the disaggregation in relation with cake layer reducation. Kaolin and polysulfon hollow fiber microfilter are used for experiment. The reduction of cake resistance by coagulation is observed in a range of 17% to 53% at the various coagulation conditions. The particle size analysis results of the experiments show that aggregated particles in feed are completely disaggregated by pump but re-aggregation of particles occurs in membrane. This suggestes that the re-aggregation of particles is critical to cake reduction and flux enhancement, since the aggregated particles are completely broken. The mechanisms for re-aggregation in membrane are the same with those for coagulation in feed tank. Charge neutralization is better for CCFMF than sweep flocculation although it has two drawbacks in operation.

• KSBB Journal
• /
• 제7권1호
• /
• pp.79-83
• /
• 1992

Erwinia rhapontici를 Ca-alginate에 고정화시켜 고정화 세포의 반응특성을 고찰하고, STR, PBR을 이용하여 Palatinose의 생산을 검토하였다. Free cell과 고정화 세포의 반응최적 pH는 5.5-6.0, 반응 최적온도는$30-35^{\circ}C$로 동일하였으나 고정화에 의해 pH 및 온도 범위가 보다 넓어졌고, 이때 Free cell및 고정화 세포의 겉보기 Km갑슨 각각 0.13, 0.28M이었다. STR을 이용한 Palatonose 생산시 고정화 세포의 반감기는 약 380 시간으로 낮았으나, PBR을 통해 30일까지 안정운전이 가능하였다. PBR 운전시의 운전온도 30, $33^{\circ}C$에서 Palatinose수율 및 고정화 세포의 안정성은 거의 동일한 결과를 나타내었으며 이때 PBR생산성은 약 120g/l$\cdot$h이었고, Pilot scale인 50L 까지 성공적으로 Scale up 되었다.