• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 추계학술대회 논문집
• /
• pp.123-128
• /
• 2002

The machining parameters for the wire electrical discharge machining(WEDM), including no load voltage, pulse-on time, pulse-off time, wire tension, water flow rata offset etc. should be chosen properly so that a better performance can be obtained An optimum selection of machining parameters relies heavily on the operators technologies and experience. This study presents a method by means of Taguchi method to select optimal machining parameter combination for an cutting speed or surface roughness. Experimental results demonstrate that the machining models are appropriate and the derived machining parameters satisfy the real requirements in notice.

• 통합자연과학논문집
• /
• 제13권3호
• /
• pp.92-96
• /
• 2020

Taguchi's robust parameter design is an approach to reduce the performance variation of quality characteristics in products and processes. In robust design, the signal-to-noise ratio (SN ratio) was used to find the optimum condition to minimize the variation of quality characteristics as much as possible and bring the average of quality characteristics closer to the target value. In this paper, we propose a simultaneous optimization method based on a linear model of the SN ratio as a method to find the optimal condition of the control factor in case of multi-characteristics. In addition, the proposed method and the existing method were compared and studied by taking actual cases.

• 한국경영과학회:학술대회논문집
• /
• 한국경영과학회/대한산업공학회 2003년도 춘계공동학술대회
• /
• pp.1077-1084
• /
• 2003

The performance of simulated annealing (SA) algorithm such as solution optimality and computation time mainly depends on how to determine the SA-related parameters Several schemes have been suggested to improve the performance of SA and several parameter design methods have been utilized to select parameter values of each scheme. In this paper, we propose a new SA algorithm design method that can determine schemes as well as parameter values simultaneously The new SA algorithm design method is based on the Taguchl method which primarily selects the design parameters for a product or process to minimize the effect of noise parameters. so that the response is close to the desired target with minimum variation. To show the effectiveness of the proposed method, extensive computation experiments are conducted.

• 대한안전경영과학회:학술대회논문집
• /
• 대한안전경영과학회 2001년도 춘계학술대회
• /
• pp.205-209
• /
• 2001

A study to analyze and solve problems of multi wire installation duct experiment has presented in this paper We have taken Taguchi's parameter design approach, specifically orthogonal array, and determined the optimal levels of the selected variables through analysis of the experimental results using S/N ratio.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2002년도 학술대회논문집
• /
• pp.173-177
• /
• 2002

A study to analyze and solve problems of multi wire installation duct experiment has presented in this paper. We have taken Taguchi's parameter design approach, specifically orthogonal array, and determined the optimal levels of the selected variables through analysis of the experimental results using S/N ratio.

• 산업공학
• /
• 제7권1호
• /
• pp.75-80
• /
• 1994

In a recent article, Leon et al. lucidly explained the ideas of the Taguchi two-stage procedure for parameter design optimization, and proposed alternative performance measures called PerMIA to the signal-to-noise ratios. On the other hand, Box proposed an empirical approach to the problem based upon monotone transformations of the performance characteristic(y). This paper develops procedures for parameter design optimization under the assumptions that the expected loss(not necessarily a mean squared error loss) is increasing with respect to the variance of the error in y, and that the mean of y satisfies certain conditions of adjustability. It turns out that the variance of the error in y can play the role of PerMIA, and it is further shown that the derived PerMIA can be adapted to the Box empirical procedure for the minimization of the expected loss in the original metric.

• 산업공학
• /
• 제5권1호
• /
• pp.25-34
• /
• 1992

A study to analyze and solve inherent problems of a pilot cola machine has been presented in this paper. The product considered in this study involves at least 16 variables(factors) which simultaneously affect the product performance. For this multi-variate statistical problem, we first carefully examined their relationships and selected four variables considered as the most important. We have taken Taguchi's parameter design approach, specifically the $L_8\:(2^7)$ orthogonal array, and determined the optimal levels of the selected variables through the analysis of the experimental results. Finally, we conclude this study with providing general comments drawn from the analysis and verification experiments.

• 반도체디스플레이기술학회지
• /
• 제13권3호
• /
• pp.7-11
• /
• 2014

The experimental analysis presented aims at the selection of the most optimal machining parameter combination for wire electrical discharge machining (WEDM) of STD11. Based on the Taguchi experimental design ($L_{27}$ orthogonal array) method, a series of experiments were performed by considering time-on, voltage, time-off, wire speed, and flow rate as input parameters. The surface roughness was considered responses. Based on the signal-to-noise (S/N) ratio, the influence of the input parameters on the responses was determined. The optimal machining parameters setting for the minimum surface roughness was found using Taguchi methodology. In order to investigate the effects of process parameters on the surface machined by WEDM, Several experiments are conducted to consider effects of time-on, voltage, time-off, wire speed and flow rate on the surface roughness. Analysis of variance (ANOVA) as well as regression analysis are performed on experimental data. The best results of surface roughness were obtained at higher voltage, lower wire speed, and lower time-on.

• 품질경영학회지
• /
• 제46권1호
• /
• pp.39-74
• /
• 2018

Purpose: For more than 30 years, robust parameter design (RPD), which attempts to minimize the process bias (i.e., deviation between the mean and the target) and its variability simultaneously, has received consistent attention from researchers in academia and industry. Based on Taguchi's philosophy, a number of RPD methodologies have been developed to improve the quality of products and processes. The primary purpose of this paper is to review and discuss existing RPD methodologies in terms of the three sequential RPD procedures of experimental design, parameter estimation, and optimization. Methods: This literature study composes three review aspects including experimental design, estimation modeling, and optimization methods. Results: To analyze the benefits and weaknesses of conventional RPD methods and investigate the requirements of future research, we first analyze a variety of experimental formats associated with input control and noise factors, output responses and replication, and estimation approaches. Secondly, existing estimation methods are categorized according to their implementation of least-squares, maximum likelihood estimation, generalized linear models, Bayesian techniques, or the response surface methodology. Thirdly, optimization models for single and multiple responses problems are analyzed within their historical and functional framework. Conclusion: This study identifies the current RPD foundations and unresolved problems, including ample discussion of further directions of study.

• 소성∙가공
• /
• 제9권3호
• /
• pp.257-264
• /
• 2000

In this study, optimization for press forming condition of low arm was performed with explicit dynamic FEM code, Pam-Stamp. FEM simulation was coupled with the Taguchi's experiment technique having three design variables - friction coefficient, plastic anisotropy parameter, and blank shape - which are chosen to be optimized. The simulation results were compared with those of experiment. We found out the change of blank shape among these three design variables is very effective in optimizing press forming condition of low arm. In addition, the modified blank shape shows high yield of slitting coil.