• 한국산업융합학회 논문집
• /
• 제7권1호
• /
• pp.63-68
• /
• 2004

There are a lot of manholes such as for water supply, sewage, telecommunication cable, traffic sign, electricity supply, and rainwater, etc. Conventional manholes installed on a road are impossible to adjust height, so that they should be entirely excavated to reinstall or repair. This entire excavation of a manhole causes too much time-consuming work, waste of resources, and obstruction of traffic. In this study, in order to solve the above mentioned problems, a cover, outer and inner parts of a manhole are integrated by gear-shaped parts located between outer and inner parts of a manhole. Mechanical design is performed to determine dimension of gear-shaped parts by Taguchi orthogonal array table. Cast molds for a gear-shaped manhole are also manufactured.

• 한국정밀공학회지
• /
• 제15권9호
• /
• pp.15-24
• /
• 1998

In this research. we have proposed a new technique to determine .the combination of design parameters for the process design of a hot forged product using artificial neural network(ANN) and statistical design of experiments(DOE). The investigated problem involves the adequate selection of the aspect ratio of billet, the ram velocity and the friction factor as design parameters. An optimal billet satisfying the forming limitation, die filling, load and energy as well as more uniform distribution of effective strain, is determined by applying the ability of artificial neural network and considering the analysis of mean and variation on the functional requirement. This methodology will be helpful in designing and controlling parameters on the shop floor which would yield the best design solution.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제3권4호
• /
• pp.446-450
• /
• 2014

This paper performed the optimal design of electromagnetic linear actuator with divided coil excitation. The table of orthogonal array and response surface methodology (RSM) are applied to maximize the clamping force of the electromagnetic linear actuator with colenoid (COL) and multipolar solenoid (MPS) excitation. The analysis results show that the clamping force of the optimal models with COL and MPS excitation are increased by 41% and 54% at the gap of 0mm compared to the initial models, respectively.

• 한국소음진동공학회논문집
• /
• 제12권6호
• /
• pp.405-412
• /
• 2002

Recently, regulations of the government and concerns of people give rise to the interest in exhaust and intake noise of passenger car as much as other vehicles. In these demands, performance prediction software with hybrid method was developed at first. Secondly, robust design was used for improving the noise reduction capacity of intake system with the performance prediction software. On the basis of the existing design, length and radios of each component that was thought to effect on the capacity of intake system was selected. The factors were arranged by using L18 table of orthogonal array and optimum value was obtained.

• 한국기계가공학회지
• /
• 제6권4호
• /
• pp.44-49
• /
• 2007

In this paper, propose an optimal design to improve the mechanical efficiency of gate valve made by forging method. In order to design the experiments using table of orthogonal array and optimization design is conducted as application of real response model to Taguchi method based approximation model using computer simulation. Also, from verification of the response model with optimized results was confirmed that usefulness and reliance of application Taguchi method to structural optimum design using finite element analysis and equation.

• 한국의류학회지
• /
• 제2권2호
• /
• pp.209-215
• /
• 1978

This experiment was designed to analyze the factors, which are very common in practical sewing, affecting on sewing shrinkage by using orthogonal array ($L_{27}$) table. The results were analyzed by using the computer program, PDP 11/10. The results showed that sewing shrinkage was increased up to 3 times of laundrying but no further changes could be found. Sewing shrinkage was affected much by the number of stitching and yarn tension and the rate increased with proportion to the number of stitching in unit length and yarn tension. When cotton yarn was used in P/C fabrics, the shrinkage was much smaller, but this results did not agree with other articles reported. Sewing by using $\sharp$11 needle and 1000$\~$1500r.p.m. seemed to lower the shrinkage rate.

• 대한가정학회지
• /
• 제29권2호
• /
• pp.35-46
• /
• 1991

After adhering theone-sided non-woven adhesive interlining to the polyester/cotton fabrics and making experiments under the various conditions by L27 Orthogonal Array Table, we examined and analyzed the breaking away strength. The rusults are summarized as follows : 1. The best length of the adhering time is 15 secs. 2. As the adehesive interlining for blouse and jacket, B3 is best 3. The pressure for the adhesion is best under the pressure of 6.2Kg. 4. The temperature for the adhesion is best at 140$^{\circ}C$. 5. As for the direction of the adhesion, three directions appear much the same breaking away strength. 6. For the better adhesion power, if the less adhering power, if the less adhering pressure is applied, the adhering time must be extended(15-20 secs), and if much stronger adhering pressure is applied, the time must be shortened(10-15 secs). In general, it is the best way for the adhesion to apply under the pressure of 6.2Kg, for 15 secs long, and at 140$^{\circ}C$ of the adhering temperature.

• 품질경영학회지
• /
• 제28권1호
• /
• pp.41-56
• /
• 2000

Recently, the regulations from the government and concerns of the people give rise to the interest in noise from a passengers car In this paper, Taguchi method is adopted to reduce the noise from the intake system of a cu. Based on the current design of the intake system, the factors such as the length and radius of each component of the intake system, which are thought to be effective for the system are arranged using L$_{18}$ table of orthogonal array Moreover, the non-controllable factors are included for the analysis. Thus, the relation between control factors and non-controllable factors are analyzed with constraints..

• 동력기계공학회지
• /
• 제15권4호
• /
• pp.11-18
• /
• 2011

A Shock absorber is one of the most important components in vehicle suspension systems. In general, many repeated analyses are required for the design of a shock absorber to satisfy the suspension characteristics of a specific automobile, like fluid flow analysis and mechanical analysis. The purpose of this study is to develop a fast design tool for shock absorber designers. One of the efficient solutions for this can be an empirical design method considering phenomenological effects from the shock absorber design variables. In order to extract the shock absorber's experimental characteristics, we used Taguchi method. This method showed that which design variables have major effects for the shock absorber's damping characteristics. This empirical design method also showed the direction of the design changes to satisfy the designer's intension.

• 한국기계가공학회지
• /
• 제14권5호
• /
• pp.102-106
• /
• 2015

In this paper, we study the optimal design for improved rotation latch system performance. The factors affecting the Torque generated in the armature were chosen as design variables. Utilizing the vertical matrix, the orthogonal array table was created to predict the results through minimal analysis. To confirm the Torque generation amount, by utilizing the commercial electromagnetic analysis software MAXWELL, finite element analysis was performed. The approximation method and experimental design through the commercial PIDO tool PIAnO for optimal design and calculations were utilized to perform experiments using an optimization method with evolutionary algorithms. Using the approximation model, design factors were determined that can maximize the torque generated in the armature, and the simulation was performed.