• Title/Summary/Keyword: TOUGH2

검색결과 192건 처리시간 0.024초

이산화탄소 지중저장 모델링: 저투수 이질협재층이 이산화탄소 거동에 미치는 영향 (Modeling Geologic Storage of Carbon Dioxide: Effects of Low-permeability Layer on Migration of CO2)

  • 한아름;김태희;권이균;구민호
    • 한국지하수토양환경학회지:지하수토양환경
    • /
    • 제22권3호
    • /
    • pp.42-49
    • /
    • 2017
  • TOUGH2 was used to simulate the migration of $CO_2$ injected into a sandy aquifer. A series of numerical simulations was performed to investigate the effects of a low-permeability layer (LPL) embedded in the aquifer on the injection rate and the pressure distribution of $CO_2$. The results show that the size and location of the LPL greatly affected the spread of $CO_2$. The pressure difference between two points in the aquifer, one each below and above the LPL, increased as the size of the LPL increased, showing a critical value at 200 m, above which the size effect was diminished. The location of the LPL with respect to the injection well also affected the migration of $CO_2$. When the injection well was at the center of the LPL, the injection rate of $CO_2$ decreased by 5.0% compared to the case with no LPL. However, when the injection well was at the edge of the LPL, the injection rate was decreased by only 1.6%. The vertical distance between the injection point and the LPL also affected the injection rate. The closer the LPL was to the injection point, the lower the injection rate was, by up to 8.3%. Conclusively, in planning geologic storage of $CO_2$, the optimal location of the injection well should be determined considering the distribution of the LPL in the aquifer.

열-수리-역학적 연계해석을 이용한 복공식 지하 압축공기에너지 저장공동의 역학적 안정성 평가 (Geomechanical Stability of Underground Lined Rock Caverns (LRC) for Compressed Air Energy Storage (CAES) using Coupled Thermal-Hydraulic-Mechanical Analysis)

  • 김형목;;류동우;신중호;송원경
    • 터널과지하공간
    • /
    • 제21권5호
    • /
    • pp.394-405
    • /
    • 2011
  • 본 연구에서는 복공식 지하 압축공기에너지 저장공동의 역학적 변형 및 누출 거동의 복합거동을 파악할 목적으로 비등온 다상다성분 유체유동 및 역학적 거동의 연계해석이 가능한 TOUGH-FLAC 해석을 실시하였다. 지하압축공기에너지 저장 공동의 초기 및 장기 운영 과정에서 고압 압축공기 인입 입출에 따른 콘크리트 라이닝 내부에 발생하는 응력 양상을 살펴보고 저장공동 내부 압력 및 온도 변화를 파악함으로써 기밀성능을 평가하였다. 최대 저장공동 운영압력 8 MPa 조건에서 콘크리트 라이닝 내부에서는 공기침투압에 의한 유효응력의 감소와 접선방향의 인장응력의 증가에 따라 인장균열이 발생할 수 있음을 확인하였다. 콘크리트 라이닝 내부의 인장균열 발생에 따른 투과특성 증가 모델을 이용한 해석 결과, 저장공동 천정부 및 측벽부 일부에서 인장파괴가 발생하여 이들 영역에서의 투과계수는 초기 $10{\times}10^{-20}m^2$에서 $5.0{\times}10^{-13}m^2$까지 증가하였다. 한편, 콘크리트 라이닝 내부 인장균열 발생 및 투과특성 증가에도 불구하고 저장공동 내부 압축공기 압력은 주변 암반의 기밀성능으로 인해 일정하게 유지되고 공기누출량은 일일주입량의 0.02%에도 못 미쳐 복공식 지하 압축공기에너지 저장공동의 유효성을 확인할 수 있었다.

국내 이산화탄소 지중격리저장 실증실험 후보부지의 역학적 안정성 평가 기초해석 (Geomechanical Stability Analysis of Potential Site for Domestic Pilot CCS Project)

  • 김아람;김형목;김현우;신영재
    • 터널과지하공간
    • /
    • 제27권2호
    • /
    • pp.89-99
    • /
    • 2017
  • 이산화탄소 지중저장 사업의 성공적인 수행을 위해서는 저장시스템의 안정성을 확보할 수 있는 대상 지층을 선정하고 현장 지질조건에 최적화된 주입 조건을 설계해야 한다. 본 연구에서는 국내 실증실험 대상 예상후보지의 하나인 장기분지의 지질구조를 바탕으로 2차원 간략해석모델을 구축하고 TOUGH-FLAC 연계해석기법을 사용하여 초기응력조건과 주입량이 이산화탄소 격리저장시스템에 미치는 영향을 분석하였다. 기초해석 결과, 수직응력이 수평응력보다 우세한 정단층 응력조건에서 전단미끄러짐 가능성이 가장 높은 결과를 보였으며, 단위시간당 주입량을 달리하는 주입량 시나리오 해석에서는 주입량을 단계적으로 증가시켜 주입하는 경우가 공극압의 증가폭이 가장 크고 활동마찰계수를 이용한 전단미끄러짐 가능성 평가 결과에서도 가장 불리한 것으로 평가되었다.

일본의 통신상호접속 요금정책 동향 및 시사점 (The Current Trend to the Policy of Telecommunication Inter-connection Charge in Japan and Its Implication)

  • 김방룡
    • 기술혁신학회지
    • /
    • 제2권3호
    • /
    • pp.129-144
    • /
    • 1999
  • In recent an official announcement of NTT about a report of LRIC Model Study Group in the end of July 1999 has evoked a tough tug-of-the -war among relevant parties pertaining to the lowering problem of iner-connectino charge in Japan. This paper mainly introduces diverse response from all relevant parties about a report of LRIC Model Study Group in Japan and sort out their significant implications to our telecommunication industry.

  • PDF

A New Wall-Distance Free One-Equation Turbulence Model

  • Nakanishi Tameo
    • 한국전산유체공학회:학술대회논문집
    • /
    • 한국전산유체공학회 2003년도 The Fifth Asian Computational Fluid Dynamics Conference
    • /
    • pp.107-109
    • /
    • 2003
  • We propose a wall distance free one-equation turbulence model. The model is organized in an extremely simple form. Only a few model constants were introduced into the model. The model is numerically tough and easy-of-use. The model also demonstrated the ability to simulate the laminar to turbulent flow transition. The model has been applied to the channel flow, the plane jet, the backward facing step flow, the flat plate boundary layer, as well as the flow around the 2D airfoil at large angles of attack, which obtained satisfactory results.

  • PDF

THM analysis for an in situ experiment using FLAC3D-TOUGH2 and an artificial neural network

  • Kwon, Sangki;Lee, Changsoo
    • Geomechanics and Engineering
    • /
    • 제16권4호
    • /
    • pp.363-373
    • /
    • 2018
  • The evaluation of Thermo-Hydro-Mechanical (THM) coupling behavior is important for the development of underground space for various purposes. For a high-level radioactive waste repository excavated in a deep underground rock mass, the accurate prediction of the complex THM behavior is essential for the long-term safety and stability assessment. In order to develop reliable THM analysis techniques effectively, an international cooperation project, Development of Coupled models and their Validation against Experiments (DECOVALEX), was carried out. In DECOVALEX-2015 Task B2, the in situ THM experiment that was conducted at Horonobe Underground Research Laboratory(URL) by Japan Atomic Energy Agency (JAEA), was modeled by the research teams from the participating countries. In this study, a THM coupling technique that combined TOUGH2 and FLAC3D was developed and applied to the THM analysis for the in situ experiment, in which rock, buffer, backfill, sand, and heater were installed. With the assistance of an artificial neural network, the boundary conditions for the experiment could be adequately implemented in the modeling. The thermal, hydraulic, and mechanical results from the modeling were compared with the measurements from the in situ THM experiment. The predicted buffer temperature from the THM modelling was about $10^{\circ}C$ higher than measurement near by the overpack. At the other locations far from the overpack, modelling predicted slightly lower temperature than measurement. Even though the magnitude of pressure from the modeling was different from the measurements, the general trends of the variation with time were found to be similar.

암반의 불균질성을 고려한 불포화대 지하수 유동 평가 (Numerical Simulation of Groundwater Flow in Feterogenetic Rockmass of Unsaturated Condition)

  • 하재철;이정환;정재열;정해룡
    • 지질공학
    • /
    • 제26권1호
    • /
    • pp.87-99
    • /
    • 2016
  • 본 연구에서는 단열을 포함하는 불포화 암반에서의 지하수 유동 흐름을 예측하기 위한 2차원 수치 모델링을 수행하였다. 특히, 불연속 단열망 모델링(Dscrete Fractured Network, DFN)을 통하여 도출된 투수계수의 분포를 나타내는 k-field를 모델링 입력변수로 적용하였다. 투수계수 차이는 불포화대에서 지하수의 이동속도 차이를 야기시키는 중요한 인자로 적용되었다. 연구지역의 지표 토양층으로부터 지하 대수층까지의 불포화대 깊이를 적용하여 지하수 유동 모델링의 초기조건을 실제와 유사하게 설정하였다. 강우의 지표 침투율은 인공구조물과 자연 토양층의 침투율 차이를 적용하여 실제 불포화 암반을 거쳐서 포화대까지 지하수의 이동흐름을 해석하고 시각화하였다. 특히, 오염물질의 이동 시작점이 될 수 있는 인공구조물의 하부에 모니터링 지점을 설정하여 실제 오염물질원이 지하수에 용해되어 불포화대를 이동할 때의 경로를 예측 하였으며 중력방향인 직하부로 이동하는 것을 확인되었다.

수주지열정의 지하수 유동 및 지열 이동 예측을 위한 수치 모델링 기법 개발 (Development of a Numerical Modeling Technique for Predicting Groundwater flow and Heat Transport in a Standing Column Well)

  • 박성민;황기섭;문종필;김중휘
    • 지질공학
    • /
    • 제26권4호
    • /
    • pp.461-471
    • /
    • 2016
  • 수주지열정의 지하수 유동 및 지열 이동 현상을 모사할 수 있는 수치 모델링 기법을 제시하기 위하여 열-수리학적 모델인 TOUGH2를 기반으로 한 모듈을 개발하였고 두 유형의 수주지열정에서의 냉방 및 난방 운영을 수치 모의하였다. 수치 모델링 결과들은 수주지열정의 냉난방 운영이 주변 지층 및 지하수와의 열교환 및 유체 혼합에 크게 영향을 받으며, 특히 PVC 또는 PE 파이프 내부와 수주지열정 내부에서 서로 반대방향으로 유동하는 유입수와 유출수 간의 열교환이 중요한 요소임을 보여준다. 또한 본 연구에서 개발 및 제안된 수치 모델링 기법이 수주지열정의 내부 구조 및 유체 유동과 열 이동 현상을 합리적으로 모사할 수 있음을 보여준다. 이러한 수치 모델링 기법은 수주지열정의 설계, 시공 및 운영 단계에서 열교환 성능을 정량적으로 분석할 때 유용하게 활용될 수 있을 것으로 기대된다.

견직물의 스치는 소리로부터 변환된 색채의 물리량과 감성 (Physical Properties and Sensibility on the Transformed Colors from the Rustling Sounds of Fabrics)

  • 김춘정;최계연;김수아;조길수
    • 감성과학
    • /
    • 제5권1호
    • /
    • pp.25-32
    • /
    • 2002
  • 본 연구에서는 7가지 실크직물의 스치는 소리를 녹음한 후, 색채로 변환시켜 변환색채에 대한 감각과 감성을 평가하고, 2차원 모형을 제시하여 감각/감성과 직물의 관계를 시각화하였다. 피험자 30명을 대상으로 변환색채에 대한 감각과 감성을 평가하도록 하였으며 색채의 물리량은 홍색비율(RP), 녹색비율(GP), 청색비율(BP)과 색채 빈도수(CC)를 계산하였다. 감성차원에 대하여 활동감, 우아함, 터프함의 세 요인이 도출되었다. 활동감 차원은 GP, CC와는 정적인 상관을 보였으며 능직물과 견방사의 교직물을 가장 활동적이라고 평가하였다 우아함 차원은 RP와는 정적상관을, CC와는 부적상관을 보였으며 수자직물과 평직물이 가장 우아하다고 평가되었다. 터프함 차원은 RP와 높은 정적상관을 가졌다. 능직물과 같이 색채 빈도수가 많고 홍색비율과 녹색비율이 많은 변환색채를 선호하였다.

  • PDF

Prediction of tenderness in bovine longissimus thoracis et lumborum muscles using Raman spectroscopy

  • Maria Sumampa Coria;Maria Sofia Castano Ledesma;Jorge Raul Gomez Rojas;Gabriela Grigioni;Gustavo Adolfo Palma;Claudio Dario Borsarelli
    • Animal Bioscience
    • /
    • 제36권9호
    • /
    • pp.1435-1444
    • /
    • 2023
  • Objective: This study was conducted to evaluate Raman spectroscopy technique as a noninvasive tool to predict meat quality traits on Braford longissimus thoracis et lumborum muscle. Methods: Thirty samples of muscle from Braford steers were analyzed by classical meat quality techniques and by Raman spectroscopy with 785 nm laser excitation. Water holding capacity (WHC), intramuscular fat content (IMF), cooking loss (CL), and texture profile analysis recording hardness, cohesiveness, and chewiness were determined, along with fiber diameter and sarcomere length by scanning electron microscopy. Warner-Bratzler shear force (WBSF) analysis was used to differentiate tender and tough meat groups. Results: Higher values of cohesiveness and CL, together with lower values of WHC, IMF, and shorter sarcomere were obtained for tender meat samples than for the tougher ones. Raman spectra analysis allows tender and tough sample differentiation. The correlation between the quality attributes predicted by Raman and the physical measurements resulted in values of R2 = 0.69 for hardness and 0,58 for WBSF. Pearson's correlation coefficient of hardness (r = 0.84) and WBSF (r = 0.79) parameters with the phenylalanine Raman signal at 1,003 cm-1, suggests that the content of this amino acid could explain the differences between samples. Conclusion: Raman spectroscopy with 785 nm laser excitation is a suitable and accurate technique to identify beef with different quality attributes.