• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.503-504
• /
• 2010

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.817-818
• /
• 2006

A 2.0T class HTS conduction cooled magnet was designed. Designing of magnet shape was performed through two steps. First step is to find a basic cross section for minimize the amount of conductor used and second step to optimize the coil shape to satisfy the magnetic field homogeneity. The magnetic fields was analyzed with FEM and the critical current value of magnet was also expected with the result of field analysis and the Ic to B curve of Bi-2223 HTS tape.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.210-212
• /
• 1996

A nonlinear optimization method for the shape optimization of actively shielded superconducting MRI magnet is presented. The presented design method can optimize both main coil and shielding coil simultaneously by setting constraints on stray field intensity at a specified distance from the magnet center. A 1 Tesla actively shielded superconducting MRI magnet, with 30cm bore diameter, is designed using the presented method.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.8
• /
• pp.1040-1046
• /
• 2018

The Permanent Magnet Synchronous Motor(PMSM) has various advantages. However, new types of research have been carried out because of rising prices of materials for rare earth magnets used in PMSM and also unstable supply. In this paper, we propose Consequent Pole(CP) type IPMSM for magnet reduction. The shape of CP type IPMSM stator was same with Basic model IPMSM. The design of the rotor shape was proceeded that CP type IPMSM achieved the same output as the basic model IPMSM. Finally, the selected model and IPMSM were compared and discussed.

• Proceedings of the KIEE Conference
• /
• 2001.04a
• /
• pp.404-406
• /
• 2001

This paper is about designing the magnetizing system which is used for magnetizing the NdFeB magnet in a squirrel cage rotor. It propose the shape of the magnetizing yoke, the number of coil turn and the capacitor discharging circuit parameter. In case of magnetizing the NdFeB magnet assembled with a squirrel cage rotor, the eddy current which is produced during magnetizing becomes a disturbance in magnetizing NdFeB magnet. Hence in this paper, we try to design optimized magnetizing system with eddy current considered by FEM(Finite Element Method).

• Progress in Superconductivity and Cryogenics
• /
• v.11 no.1
• /
• pp.49-54
• /
• 2009

This paper presents the numerical simulation results on the moving type electrodynamic suspension (EDS) simulator and static type EDS simulator using high-Tc superconducting (HTS) levitation magnet. The levitation force of the EDS system is formed by the reaction between the moving magnet and the fixed ground conductor. The possible two ways to simulate the EDS system were simulated in this paper by using finite element method (FEM). The first way was the moving type simulator which consists of the fixed HTS magnet and the moving ground conductor. The second way was the static type simulator which consists of the fixed magnet, the fixed ground conductor and the ac current supply system. To verify the characteristics of high speed EDS system with the moving type simulator heavy, large and fast moving ground conductor is needed. The static type simulator can get the characteristics of the high speed EDS system by applying equivalent ac current to velocity, therefore it does not need large moving part. The static type EDS simulator, which can consist of an HTS magnet, the fixed ground conductor(s), an AC power supply and the measuring devices, also test the effect of the shape of the ground conductor easily. The plate type ground conductor made stronger levitation force than ring type ground conductor. Although the outer diameter 335 mm ring type ground conductor (Ring3) was larger than the outer diameter 235 mm ground conductor (Ring2), the levitation force by Ring2 was stronger than that by Ring3. From the calculation results on this paper, the consideration of the magnetic flux distribution according to the levitation height should be included in the process of the ground conductor design.

• Proceedings of the KIEE Conference
• /
• 2003.10b
• /
• pp.113-115
• /
• 2003

This paper presents the optimal design of a brushless DC motor(BLDC) keeping the average torque and cogging torque of the initial model while minimizing the volume of magnet pole by FEM and evolution strategy. Experimental tests are performed by the finite element method(FEM), and the random based evolution strategy is applied for the shape optimization. The optimal result shows a largely reduced volume of magnet pole.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2004.04a
• /
• pp.291-298
• /
• 2004

The observations of rapid motion of bubbles under water for approximately 50 ms or less in high-magnetic fields of 10 T have been carried out successfully for the first time. The observation system constructed is composed of a high-speed video camera, a telescope, a cryostat with a split-type superconducting magnet, a light source, a mirror and a transparent sample cell. Using this system, the influence of magnetic field on the path and shape of single bubbles of O$_2$ (paramagnetism) and N$_2$ (diamagnetism) has been examined carefully. Experimental values describing the path are in good agreement with theoretical values calculated on the basis of the magneto-Archimedes effect, despite the effect of magnetism on the bubble. However, no effect of magnetism on the shape of the bubble is observed. In addition, the influence of magnetic field on drag coefficient of the bubble is discussed.

• Journal of Navigation and Port Research
• /
• v.28 no.2
• /
• pp.141-148
• /
• 2004

The observations of rapid motion of bubbles under water for approximately 50ms or less in high . magnetic fields of 10 T have been carried out successfully for the first time. The observation system constructed is composed of a high-speed video camera, a telescope, a cryostat with a split-type superconducting magnet, a light source, a mirror and a transparent sample cell. Using this system, the influence of magnetic field on the path and shape of single bubbles of $O_2$(paramagnetism) and $N_2$ (diamagnetism) has been examined carefully. Experimental values describing the path are in good agreement with theoretical values calculated on the basis of the magneto-Archimedes effect, despite the effect of magnetism on the bubble. However, no effect of magnetism on the shape of the bubble is observed In addition, the influence of magnetic field on drag coefficient of the bubble is discussed.

• Korean Journal of Heritage: History & Science
• /
• v.54 no.1
• /
• pp.206-219
• /
• 2021

The warming of the climate is increasing the damage caused by termites to wooden buildings, cultural properties and houses. A group removal system can be installed around the building to detect and remove termite damage; however, if the site is not visited regularly, every one to two months, you cannot observe whether termites have spread within, and it is difficult to take prompt effective action. In addition, since the system is installed and operated in an exposed state for a long period of time, it may be ineffective or damaged, resulting in a loss of function. Furthermore if the system is installed near a cultural site, it may affect the aesthetic environment of the site. In this study, we created a detection system that uses wood, cellulose, magnets, and magnetic sensors to determine whether termites have entered the area. The data was then transferred to a low power LoRa Network which displayed the results without the necessity of visiting the site. The wood was made in the shape of a pile, and holes were made from the top to the bottom to make it easier for termites to enter and produce a cellulose sample. The cellulose sample was made in a cylindrical shape with a magnet wrapped in cellulose and inserted into the top of a hole in the wood. Then, the upper part of the wood pile was covered with a stopper to prevent foreign matter from entering. It also served to block external factors such as light and rainfall, and to create an environment where termites could add cellulose samples. When the cellulose was added by the termites, a space was created around the magnet, causing the magnet to either fall or tilt. The magnetic sensor inside the stopper was fixed on the top of the cellulose sample and measured the change in the distance between the magnet and the sensor according to the movement of the magnet. In outdoor experiments, 11 cellulose samples were inserted into the wood detection system and the termite inflow was confirmed through the movement of the magnet without visiting the site within 5 to 17 days. When making further improvements to the function and operation of the system it in the future, it is possible to confirm that termites have invaded without visiting the site. Then it is also possible to reduce damage and fruiting due to product exposure, and which would improve the condition and appearance of cultural properties.