• Journal of Mechanical Science and Technology
• /
• 제18권6호
• /
• pp.1002-1009
• /
• 2004

Direct contact air conditioning systems, in which heat and mass are transferred directly between air and water droplets, have many advantages over conventional indirect contact systems. The purpose of this research is to investigate the cooling and heating performances of direct contact air conditioning system for various inlet parameters such as air velocity, air temperature, water flow rate and water temperature. The experimental apparatus comprises a wind tunnel, water spray system, scrubber, demister, heater, refrigerator, flow and temperature controller, and data acquisition system. The inlet and outlet conditions of air and water are measured when the air contacts directly with water droplets as a counter flow in the spray section of the wind tunnel, and the heat and mass transfer rates between air and water are calculated. The droplet size of the water sprays is also measured using a Malvern Particle Analyzer. In the cooling conditions, the outlet air temperature and humidity ratio decrease as the water flow rate increases and as the water temperature, air velocity and temperature decrease. On the contrary, the outlet air temperature and humidity ratio increase in the heating conditions as the water flow rate and temperature increase and as the air velocity decreases.

• 한국농공학회지
• /
• 제41권1호
• /
• pp.60-71
• /
• 1999

This study was performed to improve underirable warm greenhouse environment by fog cooling system in summer season. The resultsof droplet size analysis and cooling effects for fog cooling system are summarized as follows ; 1. At the pump pressure of 70kgf/$\textrm{cm}^2$ , the mean (SMD) drop size was 22.6${\mu}{\textrm}{m}$ and the maximum and minimum drop size was 45.68${\mu}{\textrm}{m}$ and 1.73${\mu}{\textrm}{m}$ , respectively, and almost all of the drop size was less than 40${\mu}{\textrm}{m}$. 2. The temperature of fog cooling greenhouse with 60% shading was dropped more than 2$^{\circ}C$ below the ambient temperature , while the greenhouse temperature without shading was 1$^{\circ}C$ higher than the ambient temperature. 3. It was found that fog spraying intervals were significantly influential on cooling effect. 4. When the greenhouse was ventilated sufficiently by natural vent system, green house temperature could be maintained by 2.5$^{\circ}C$ lower than the ambient temperature, while it was difficult to drop the greenhouse temperature below ambient temeperature without sufficient ventilation. 5. It was found that the temperature of experimental greenhouse could be maintained 3$^{\circ}C$ to 14$^{\circ}C$ lower that of control greenhouse though there were variations depending on experimental and weather conditions.

• 한국물환경학회지
• /
• 제27권6호
• /
• pp.769-775
• /
• 2011

An experimental study of biofilm nitritation system for high-strength ammonium wastewater has been carried out to examine the temperature effect on different organic and solid concentration. Operating temperature varied from $35^{\circ}C$ to $15^{\circ}C$. The influent N concentration of identical three reactors was adjusted to about $300mg\;NH_4-N/L$. A control unit fed with a synthetic wastewater, while the others were fed with reject water which is consisted of the supernatant of both digester and thickener. The results indicated that nitrite accumulation was stable in temperature range of $35^{\circ}C$ to $25^{\circ}C$. However, nitritation was significantly reduced at below $20^{\circ}C$. Free ammonia (FA) and free nitrous acid (FNA) were major inhibitors to the nitrite oxidizer for nitrite accumulation in lower temperature. From the estimation of temperature coefficient (${\Theta}$) of biofilm and suspended nitritation system, biofilm nitritation system could absorb the negative temperature effect compared with suspended nitritation system.

• Smart Structures and Systems
• /
• 제34권1호
• /
• pp.41-50
• /
• 2024

The accurate measurement of temperature in the ground source heat pump system is crucial for assessing the thermal response of the system and validating the numerical model for parametric study, which is necessary for the thermal performance evaluation of the geothermal energy system. Conventional temperature sensors have some disadvantages such as they are difficult to install, and their position can be shifted during the backfill process of the ground heat exchanger. In this study, Fiber Bragg Grating (FBG) sensors were used to measure the temperature change of a recently developed ground heat exchanger (Coil Column Unit, CCU). FBG sensors were first calibrated in a thermal chamber alongside a correlation sensor (RTD sensor). The calibrated sensors were then mounted on the pipe surface at each spiral of the CCU to measure how temperature changes during the in-door mockup thermal response test. Finally, the measurement results of the FBG sensors were verified with a finite element coded program. The results indicated that the temperature difference between the numerical analysis and the experiment was less than 1%, which is significantly lower than that of the previous study using the RTD sensors. Therefore, it is feasible to apply FBG sensors for temperature measurement during the operation of the TRT of the geothermal energy system.

• Journal of Electrical Engineering and Technology
• /
• 제12권2호
• /
• pp.904-910
• /
• 2017

This paper presents temperature measurement of solar photovoltaic modules using the custom-made system composed of an infrared temperature sensor and a microcontroller. The obtained measurement results are processed, displayed and stored on a PC using the custom-made virtual instrument. The proposed system overcomes some of the problems related to the contact sensor application, and at the same time offers accurate readings and better flexibility. The proposed system is especially suitable for applications where the cost is a limiting factor in the choice of measuring system. The conducted analysis and the obtained results have shown an excellent accuracy of the proposed system in comparison to a high quality thermal imaging camera used as the reference instrument.

• Journal of Advanced Marine Engineering and Technology
• /
• 제37권3호
• /
• pp.260-265
• /
• 2013

Impressed current cathodic protection (ICCP) system is one of the most promising corrosion protection methods. The Effect of ICCP system can be changed at diverse conditions. Particularly, temperature and relative humidity plays a crucial role in CP (Cathodic Protection) effect. Thus, in this study, the influence of temperature and relative humidity on concrete specimens was investigated. Specimens were concrete slab type with a base of $400mm{\times}400mm$ and height of 70mm. To enhance the effect of CP system, seawater was used as an electrolyte. Used anode for ICCP system was mixed metal oxide (MMO) titanium. Test factors were natural potential, CP potential, CP current, and 4-hour depolarization potential. From this study, it could be confirm that CP potential and current were highly influenced by temperature and relative humidity.

• 전자공학회논문지SC
• /
• 제39권1호
• /
• pp.1-6
• /
• 2002

본 논문에서는 제한된 센서를 이용한 에어콘의 온도제어용 실내 ·외 온도 추론 시스템을 제안하였다. 제안한 온도추론 시스템은 자연계의 면역 시스템의 네트워크 이론을 이용한 실내온도 추론과정과 실외온도 추론과정으로 구성되어 있으며, 실시간 온도추론이 가능하도록 설계하였다. 면역기법을 이용한 온도 추론 시스템은 과거의 정보를 효과적으로 이용함으로써 주어진 입력 데이터뿐만 아니라 학습되지 않는 데이터에 대해서도 온도 추론능력이 우수하다.

• 동력기계공학회지
• /
• 제10권1호
• /
• pp.90-95
• /
• 2006

Pneumatic control systems have been mainly used as a high speed operating system. Therefore, state change of air in a control volume was assumed to be adiabatic change and, pneumatic control systems have been analyzed by using this assumption. Especially, when absolute value of pressure change in the control volume is small, there is a tendency to neglect effect of temperature change on pneumatic control system because temperature change owing to pressure change is small. In this study, an effect of temperature change of air on the decompression control process was analyzed by considering change of mass flow rate, and heat transfer characteristics between air in the chamber and the chamber wall. As a result, this study could confirm that a slight temperature change of the air in the pneumatic pressure control system can influence on the dynamic characteristics of pressure response, and pressure control performance.

• Computers and Concrete
• /
• 제24권5호
• /
• pp.437-444
• /
• 2019

PLC and its expansion module, electric ball valve and cooling pipe, electric heating steel plate and various components of the system, which is used to control test and process data. By automatically adjusting the opening of the valve, the system makes the top temperature and cooling speed develop along the ideal temperature diachronic curve. Moreover, the system enables the temperature difference between inside and surface of test block limited in a given range by automatically controlling the surface board heating. The method of physical simulation test by sandbox with built-in cooling water pipe and heating rod is adopted. On the premise of a given standard value, the operation of the system is checked under different working conditions. Further, an extension of this system is proposed, which enables its application to obtain some thermal parameters when cooperating with numerical simulation.

• Journal of Yeungnam Medical Science
• /
• 제16권2호
• /
• pp.193-199
• /
• 1999

저자들은 다양한 진료 환경과 연구 수행에 폭 넓게 이용할 수 있는 새로운 온도측정 시스템을 개발하기 위하여 임상에서 필요한 기능과 연구에 요구되는 기능을 가진 간편하고 편리한 온도측정 시스템을 개발하였다. 이 측정 시스템은 일정한 지점의 온도를 정확하고 신속하게 측정하여 기록할 수 있는 장치로서 실용 가능성을 다양하게 검증해 본 결과 기존의 평면적인 열 분포도보다 진보된 등온곡선을 도출할 수 있었으며, 기존의 체온 측정장치보다 더욱 편리하게 진료의 각 분야에 효과적으로 이용할 수 있음을 확인하였다. 본 연구결과에 의한 기대효과 및 향후 활용방안으로는 1) 환자의 체온 변화를 신속하게 진단할 수 있어서 치료효과의 극대화와 부작용의 최소화에 기여할 수 있다. 2) 체온의 변화를 일으키는 다양한 질환의 진단 및 치료성과 판정에 이용할 수 있다. 3) phantom을 이용한 다양한 실험적 연구를 수행할 수 있다. 4) 장기 입원중인 환자들을 대상으로 중앙통제 방식으로 환자들의 상태를 지속적으로 감시할 수 있어서 간호인력의 노동력 절약에 많은 도움을 줄 수 있다. 5) 현재의 기능을 더욱 발전시키면 다양한 질환의 환자들에게 두루 적용할 수 있으며, 환자 감시체제를 위한 필수장비로 이용할 수도 있다.