• Korean Journal of Agricultural Science
• /
• v.11 no.2
• /
• pp.223-232
• /
• 1984

The influences of some factors involved in removing glucose from egg white by the glucose oxidase system be fore drying were investigated. And the properties between foams prepared from raw and enzyme-treat ed egg white was compared. The results obtained we re summarized as follows; 1. The dianisidine method was found to be suitable for the measurement of egg white glucose in the range up to 100ug/ml. 2. The optimal pH of glucose oxidase activity on glucose was found to be a bout 5.0, and thats activity was most stable in the pH range of about 4.0~5.0 when that enzyme was treat ed for 30 minute at $50^{\circ}C$. 3. The optimal temperature for glucose oxidase reaction on glucose was found to be about $20^{\circ}C$, and that enzyme activity was s table up to $50^{\circ}C$. 4. The removing rate of glucose from egg white with glucose oxidase was influenced by the enzyme concentration, pH and oxygen addition, and the react ion time of the desugarization was about 10 hour sunder the conditions of 0.5% hydrogen peroxide, pH 7.0 and $26^{\circ}C$. 5. All of the each egg white treated with glucose oxidase, glucose oxidase+pancreatin, glucose oxidase+trypsin showed highly foaming ability than that of natural egg white(control), but thats foam stability, on the contrary, was reversed.

• Food Science of Animal Resources
• /
• v.27 no.2
• /
• pp.228-234
• /
• 2007

The purpose of this study was to investigate quality characteristics of the meat batter containing dietary fiber extracted rice bran. The formulations of meat batters were manufactured in a model system with 2% raw rice bran and 2, 4, 6% levels of dietary fiber extracted rice bran, respectively. The proximate compositions of dietary fiber extracted rice bran were 53.27% dietary fiber, 6.10% crude fat, 22.99% crude protein, 12.78% crude moisture, and 7.41% crude ash. Compared with control of uncooked meat batter, the pH value of all treatments were significantly different(p<0.05). The pH of cooked meat batter were similar to uncooked meat batter. $CIE\;L^*-\;and\;CIE\;b^*-value$ of uncooked meat batter containing dietary fiber extracted rice bran were lower than control, but CIE $a^*-value$ of treatment was higher than those in control(p<0.05). All treatments had significantly lower cooking loss and emulsion stability than control(p<0.05). Compared with control, viscosity of the treatments containing dietary fiber extracted rice bran were observed significantly higher than those in control (p<0.05). And then hardness, cohesiveness, gumminess, and chewiness of treatments were higher than in control(p<0.05). Conclusively, the results of this study showed that addition of dietary fiber extracted rice bran affected the high quality properties of meat batter.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.5
• /
• pp.855-867
• /
• 2018

When a weak zone exists ahead of tunnel face, the stress in the adjacent area would increase due to the longitudinal arching effect and the stability of the tunnel is affected. Therefore, it is critical to prepare a countermeasure through the investigation of the frontal weakness zone of the excavated face. Although there are several researches to predict the existence of weak zone ahead of tunnel face, such as geophysical exploration, numerical analysis and tunnel support, lack of studies on the relaxation zone depending on the width or distance from the vulnerable area. In this study, the impact of the weak zone on the formation of the relaxation zone was investigated. For this purpose, a series of laboratory test were carried out varying the width of the weak zone and the separation distance between tunnel face and weak zone. In the model test, sand with a water content of 3.8% was used to form a model ground. The model weak zone was constructed with dry sand curtains. The tunnel face was adjusted to allow a sequential excavation of upper and lower half part. load cells were installed on the bottom of the foundation and the tunnel face and measuring instruments for displacement were installed on the surface of the model ground to measure the vertical stress and surface displacements due to tunnel excavation respectively. The test results show that the width of weak zone did not affect the ground settlement while the ground subsidence drastically increased within 0.25D. The vertical stress and horizontal stress increased from 0.5D or less. In addition, the longitudinal arching effect is likely within the 1.0D zone ahead of the tunnel face, which may reduce the vertical stress in the ground following tunneling direction.

• KSBB Journal
• /
• v.23 no.1
• /
• pp.90-95
• /
• 2008

In this study, a combined process of sequential anaerobic-aerobic digestion (SAAD), fluidized-bed bioreactor (FBBR), and ultrafiltration (UF) for the treatment of small scale food waste leachate was developed and evaluated. The SAAD process was tested for performance and stability by subjecting leachate from food waste to a two-phase anaerobic digestion. The main process used FBBR composed of aerators for oxygen supply and fluidization, three 5 ton reaction chambers containing an aerobic mesophilic microorganism immobilized in PE (polyethylene), and a sedimentation chamber. The HRTs (hydraulic retention time) of the combined SAAD-FBBR-UF process were 30, 7, and 1 day, and the operation temperature was set to the optimal one for microbial growth. The pilot process maintained its performance even when the CODcr of input leachate fluctuated largely. During the operation, average CODcr, TKN, TP, and salt of the effluent were 1,207mg/L, 100mg/L, 50 mg/L, and 0.01 %, which corresponded to the removal efficiencies of 99.4%, 98.6%, 89.6%, and 98.5%, respectively. These results show that the developed process is able to manage high concentration leachate from food waste and remove CODcr, TKN, TP, and salt effectively.

• Journal of the Society of Disaster Information
• /
• v.9 no.4
• /
• pp.449-461
• /
• 2013

As the hydrofluoric acid leak in Gumi-si, Gyeongsangbuk-do or hydrochloric acid leak in Ulsan, Gyeongsangnam-do demonstrated, chemical related accidents are mostly caused by large amounts of volatile toxic substances leaking due to the damages of storage tank or pipe lines of transporter. Safety assessment is the most important concern because such toxic material accidents cause human and material damages to the environment and atmosphere of the surrounding area. Therefore, in this study, a hydrofluoric acid leaked from a storage tank was selected as the study example to simulate the leaked substance diffusing into the atmosphere and result analysis was performed through the numerical Analysis and diffusion simulation of ALOHA(Areal Location of Hazardous Atmospheres). the results of a qualitative evaluation of HAZOP (Hazard Operability)was looked at to find that the flange leak, operation delay due to leakage of the valve and the hose, and toxic gas leak were danger factors. Possibility of fire from temperature, pressure and corrosion, nitrogen supply overpressure and toxic leak from internal corrosion of tank or pipe joints were also found to be high. ALOHA resulting effects were a little different depending on the input data of Dense Gas Model, however, the wind direction and speed, rather than atmospheric stability, played bigger role. Higher wind speed affected the diffusion of contaminant. In term of the diffusion concentration, both liquid and gas leaks resulted in almost the same $LC_{50}$ and ALOHA AEGL-3(Acute Exposure Guidline Level) values. Each scenarios showed almost identical results in ALOHA model. Therefore, a buffer distance of toxic gas can be determined by comparing the numerical analysis and the diffusion concentration to the IDLH(Immediately Dangerous to Life and Health). Such study will help perform the risk assessment of toxic leak more efficiently and be utilized in establishing community emergency response system properly.

• The Journal of Korean Society for Radiation Therapy
• /
• v.22 no.2
• /
• pp.123-129
• /
• 2010

Purpose: The purpose of this study was to evaluate dosimetric characteristics of Optically stimulated luminescent dosimeters (OSLD) for dosimetry Materials and Methods: InLight/OSL $NanoDot^{TM}$ dosimeters was used including $Inlight^{TM}MicroStar$ Reader, Solid Water Phantom, and Linear accelerator ($TRYLOGY^{(R)}$) OSLDs were placed at a Dmax in a solid water phantom and were irradiated with 100 cGy of 6 MV X-rays. Most irradiations were carried out using an SSD set up 100 cm, $10{\times}10\;cm^2$ field and 300 MU/min. The time dependence were measured at 10 minute intervals. The dose dependence were measured from 50 cGy to 600 cGy. The energy dependence was measured for nominal photon beam energies of 6, 15 MV and electron beam energies of 4-20 MeV. The dose rate dependence were also measured for dose rates of 100-1,000 MU/min. Finally, the PDD was measured by OSLDs and Ion-chamber. Results: The reproducibility of OSLD according to the Time flow was evaluated within ${\pm}2.5%$. The result of Linearity of OSLD, the dose was increased linearly up to about the 300 cGy and increased supralinearly above the 300 cGy. Energy and dose rate dependence of the response of OSL detectors were evaluated within ${\pm}2%$ and ${\pm}3%$. $PDD_{10}$ and PDD20 which were measured by OSLD was 66.7%, 38.4% and $PDD_{10}$ and $PDD_{20}$ which were measured by Ion-chamber was 66.6%, 38.3% Conclusion: As a result of analyzing characteration of OSLD, OSLD was evaluated within ${\pm}3%$ according to the change of the time, enregy and dose rate. The $PDD_{10}$ and $PDD_{20}$ are measured by OSLD and ion-chamber were evaluated within 0.3%. The OSL response is linear with a dose in the range 50~300 cGy. It was possible to repeat measurement many times and progress of the measurement of reading is easy. So the stability of the system and linear dose response relationship make it a good for dosimetry.

• Journal of the Korean Wood Science and Technology
• /
• v.11 no.3
• /
• pp.49-57
• /
• 1983

This study dealts with the penetration of methyl methacrylate(MMA) monomer-solvent system into five Korean major tree species, especially the Pinus koraiensis S. et Z., Pinus densiflora S. et Z., Larix leptoiepis Gordon, Quercus serrata Thunb. and Betula platyphylla var japonica Hara. In this report I described the results of the interaction between wood and polymer loading by catalyst-heat polymerization. On the other hand the influence of penetration of polymer loading on dimensional stabilization on WPC of Pinus koraiensis by catalyst-heat polymerization was also investigated.

• Economic and Environmental Geology
• /
• v.35 no.2
• /
• pp.103-112
• /
• 2002

Despite the ecological importance of potentially phytotoxic $Al_{13}$-tridecamer and its formation in the simulated condition, it was not recognized in the natural soil environment. Here we performed thermodynamic calculations to examine the stability condition of $Al_{13}$-tridecamer based on the solubility of AI in the Bo horizon of Andisols, Jeju Island, dominantly composed of AI-containing solid phases such as $Al(OH)_{3}$, proto-imogolite and/or imogolite. We have found that $Al(OH)_{3}$, proto-imogolite and/or imogolite may control Al solubility in the moderate acid condition. It means that AI total activity of the soil solution equilibrated with these solid phases ranges from $10^{-6}$ ~ $10^{-8}$M in the pH 5 to 7. Calculations based on the thermodynamic data strongly indicate that the formation of $Al_{13}$-tridecamer closely related to the total activity of AI in the system. For example, for the formation of $Al_{13}$-tridecamer of $10^{-5}$M, Al total activity of $3{\times}10^{-3}$M are needed at pH 4, and $2{\times}10^{-5}$M in the pH 5 to 7. Therefore, this research and the thermodynamic consideration suggest strongly that $Al_{13}$-tridecamer should be negligible in natural soils, especially Andisols and Spodosols, These mainly contain $Al(OH)_{3}$, proto-imogolite and/or imogolite, which could prevent the formation of $Al_{13}$-tridecamer by controlling the AI total activity low. It means that the toxicity of $Al_{13}$-tridecamer with the increase of soil acidification may be considered to be definitely low.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.10
• /
• pp.41-53
• /
• 2016

Stability of the braced earth wall in the composite ground, which is composed of the jointed base rocks and the soil strata depends on the earth pressure acting on it. In most cases, the earth pressure is calculated by the empirical method, in which base rocks are considered as a soil strata with the shear strength parameters of base rocks. In this case the effect of the joint dips of the jointed base rocks is ignored. Therefore, the calculated earth pressure is smaller than the actual earth pressure. In this study, the magnitude and the distribution of the earth pressure acting on the braced wall in the composite ground depending on the joint dips of the base rocks and the ratio of soil strata and base rocks were experimentally studied. Two dimensional large-scale model tests were conducted in a large scale test facility (height 3.0 m, length 3.0 m and width 0.5 m) by installing 10 supports in a scale of 1/14.5. The test ground was presumed with the base rock ratio of the composite ground of 65%:35% and 50%:50% and with the joint dips for each base rock layer, $0^{\circ}$, $30^{\circ}$, $45^{\circ}$ and $60^{\circ}$, respectively. And then finite element analyses were performed in the same condition. As results, the earth pressure on the braced wall increased as the base rock layer's joint dips became larger. And earth pressure at the rock layer increased as the rock rate became larger. The largest earth pressure was measured when the base rock rate was 50% (R50) and the rock layer's joint dips was $60^{\circ}$. Based on these results, a formular for the calculation of the earth pressure in the composite ground could be suggested. Distribution of earth pressure was idealized in a quadrangular form, in which the magnitude and the position of peak earth pressure depended on the rock ratio and the joint dips.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.28 no.2
• /
• pp.119-126
• /
• 2012

State of problem: Cement-retained implant-supported prostheses are routinely used in dentistry. The use of high strength cements has become more popular with the increasing confidence in the stability of the implant-abutment screw connection and the high survival rates of osseointegrated implants. No clinical data on retention of metal copings using CAD/CAM. To evaluate retention of metal copings using CAD/CAM system bonded to short titanium abutment with four different cements and compare retentive strength of metal copings with sandblasting or without sandblasting before cementation. Forty titanium abutment blocks were fabricated and divided into 4 groups of 10 samples each. Forty metal copings with occlusal hole to allow for retention testing were fabricated using CAD/CAM technology. The four cements were Fujicem(Fuji, Japan), Maxcem Elite(Kerr, USA), Panavia F2.0(Kurarary, Japan) and Superbond C&B(Sunmedical, Japan). The copings were cemented on the titanium abutment according to manufacture's recommendation. All samples were stored for 24h at 37oC in 100% humidity and tested for retention using universal testing machine(Instron) at a crosshead speed of 1.0mm/min. Force at retentive failure was recorded in Newton. The mode of failure was also recorded. Means and standard deviations of loads at failure were analyzed using ANOVA and Paired t-test. Statistical significance was set at P<0.05. Panavia F2.0 provided significantly higher retentive strength than Fujicem, Maxcem Elite(P<0.05). Sandblasting significantly increased bond strength(P<0.05). The mode of failure was cement remaining principally on metal copings. Within the limitation of this study, Panavia F2.0 showed significantly stronger retentive strength than Fujicem, Maxcem Elite(p<0.05). The Ranking order of the cements to retain the copings was Panavia F2.0, Fujicem = Maxcem Elite. Sandblasting significantly increased bond strength(P<0.05). The retentive strength of metal copings on implant abutment were influenced by surface roughness and type of cements.