• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.5
• /
• pp.268-273
• /
• 2017

In this study, nickel hydroxide crystalline powders were synthesized by continuous reaction in the taylor fluid flow using nickel chloride, nickel sulphate and sodium hydroxide as raw materials and compared with those prepared by a conventional batch type reaction. The crystallinity of nickel hydroxide prepared by the Taylor fluid flow reaction was higher than that of nickel hydroxide obtained by batch reaction. The particle size of nickel hydroxide decreased about 2.5 to 3.6 times, and the specific surface area was increased.

• Journal of Powder Materials
• /
• v.12 no.2 s.49
• /
• pp.136-145
• /
• 2005

Graphite-Ni composite powders were synthesized by mechanical alloying(MA) and spray drying(SD). Fabricated powders as well as commercial graphite-Ni powders were thermally sprayed on mild steel substrates using high velocity oxygen fuel (HVOF) thermal spray process and flame thermal spray process. The effects of several process parameters on related properties in thermally sprayed coatings have been investigated and correlated with microstructures in this study. The results indicated that the desired properties can be obtained when commercial powders were applied using HVOF process, while coating properties in case of MA powder application were inferior to those in HVOF process in so far. However, it is suggested that property enhancement can be obtained if the fraction of hexagonal graphite phase can be increased in mechanically alloyed powders.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.464-465
• /
• 2006

Monodispersed and nano-sized Cu powders were synthesized from copper sulfate pentahydrate $(CuSO_4{\cdot}5H_2O)$ inside a nonionic polymer matrix by using wet chemical reduction process. The sucrose was used as a nonionic polymer network source. The influences of a nonionic polymer matrix on the particle size of the prepared Cu powders were characterized by means of X-ray diffraction), scanning electron microscopy), and particle size analysis). The smallen Cu powders with size of approximately 100 nm was obtained with adding of 0.04M sucrose at reaction temperature of $60\;^{\circ}C$. The particle size of the Cu powders prepared by the reduction inside polymer network was strongly dependent of the sucrose content and reaction temperature.

• Journal of Powder Materials
• /
• v.17 no.1
• /
• pp.52-58
• /
• 2010

Bulk nanostructured metallic materials are generally synthesized by bottom-up processing which starts from powders for assembling bulk materials. In this study, the bottom-up powder metallurgy and High Pressure Torsion (HPT) approaches were combined to achieve both full density and grain refinement at the same time. After the HPT process at 473K, the disk samples reached a steady state condition when the microstructure and properties no longer evolve, and equilibrium boundaries with high angle grain boundaries (HAGBs) were dominant. The well dispersed alumina particles played important role of obstacles to dislocation glide and to grain growth, and thus, reduced the grain size at elevated temperature. The small grain size with HAGBs resulted in high strength and good ductility.

• Journal of the Korean Ceramic Society
• /
• v.44 no.1 s.296
• /
• pp.37-42
• /
• 2007

The preparation of $TiC_{0.7}N_{0.3}$ powder by SHS in the system of $Ti-TiH_2-C$ ($N_2$ atmosphere) was investigated in this study. In the preparation of $TiC_{0.7}N_{0.3}$ powder, the effect of gas pressure, compositions such as Ti, $TiH_2$, C, and additive in mixture on the reactivity were investigated. At 50 atm of the initial inert gas pressure in reactor, the optimum composition for the preparation of pure $TiC_{0.7}N_{0.3}$ was $0.75Ti+0.25TiH_2+0.7C+0.5NaCl$. The $TiC_{0.7}N_{0.3}$ powder synthesized in this condition was a single phase with irregular shape.

• Journal of the Korean Ceramic Society
• /
• v.43 no.10 s.293
• /
• pp.595-600
• /
• 2006

The preparation of $\beta$-SiAlON powder by SHS in the system of $Si-Al-SiO_2-NH_4F(\beta-Si_3N_4)$ was investigated in this study. In the preparation of SiAlON powder, the effect of gas pressure, compositions such as Si, $NH_4F$, \beta-Si_3N_4$ and additive in mixture on the reactivity were investigated. At 50 atm of the initial inert gas pressure in reactor, the optimum composition for the preparation of pure $\beta$-SiAlON was $3Si+Al+2SiO_2+NH_4F$. The $\beta$-SiAlON powder synthesized in this condition was a single phase $\beta$-SiAlON with a rod like morphology.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.6
• /
• pp.383-388
• /
• 2019

High purity SiC fine powder with metal impurity contents of less than 1 ppm was synthesized by improved carbothermal reduction process, and the synthesized powder was used for SiC single crystal growth in RF heating PVT device at temperature above 2,100℃. In-situ x-ray image analyzer was used to observe the sublimation of the powder and single crystal growth behavior during the growth process. SiC powder was used as a source of single crystal growth, exhausted from the outside of the graphite crucible at the growth temperature and left graphite residues. During the growth, the flow of raw materials was concentrated in the middle and influenced the growth behavior of SiC single crystals. This is due to the difference in temperature distribution inside the crucible due to the fine powder. After the single crystal growth was completed, the single crystal ingot was cut into a 1 mm thick single crystal substrate and finely polished using a diamond abrasive slurry. A dark yellow 4H-SiC was observed overall of single crystal substrate, and the polycrystals generated in the outer part may be caused by the incorporation of impurities such as the bubble layer mixed in the process of attaching the seed crystal to the seed holder.

• Journal of Electrochemical Science and Technology
• /
• v.8 no.2
• /
• pp.146-154
• /
• 2017

In this study, copper (II) oxide was prepared for use in a copper electroplating solution. Copper chloride powder and copper (II) oxide are widely used as raw materials for electroplating. Copper (II) oxide was synthesized in this study using a two-step chemical reaction. Herein, we developed a method for the preparation of copper (II) oxide without the use of sintering. In the first step, copper carbonate was prepared without sintering, and then copper (II) oxide was synthesized without sintering using sodium hydroxide. The optimum amount of sodium hydroxide used for this process was 120 g and the optimum reaction temperature was $120^{\circ}C$ regardless of the starting material.

• Journal of the Korean Ceramic Society
• /
• v.38 no.11
• /
• pp.959-961
• /
• 2001

Nanosized CeO$_2$Powders were prepared under high temperature and pressure conditions by precipitation from metal nitrates with aqueous potassium hydroxide. Spherical shape of CeO$_2$powder was obtained at 175$^{\circ}C$ for 6h. TEM and X-ray diffraction patterns showed that the synthesized particle was crystalline. The average size and size distribution of the synthesized particles were below 30 nm and narrow, respectively. In addition, the effects of synthesis parameters under hydrothermal process are discussed.

• Journal of the Korean Ceramic Society
• /
• v.33 no.7
• /
• pp.743-754
• /
• 1996

In this study (Ba1-xPbx)TiO3 was synthesized by modified oxalate process in order to prevent vaporization of PbO through low temperature synthesis climinate Cl ion reproducibly substitute Pb for by and uniformly distribute ion (Ba1-xPbx)TiO3 was synthesized by coprecipitation of lead acetate barium acetate and ammonium titanyl oxalate have been used as starting materials. The substitution of Pb for Ba was reproducibly possible synthetic temperature of perovskite structure becomes lowed as the Pb concentration increases and fine partic-les (specific surface are :7.2 cm2/g) were obtained, BaTiO3 powders calcined at 90$0^{\circ}C$ for 3 hours were cubic from in XRD analysis and as Pb content was increases evident split of tetragonal peaks could be observed The optimum conditions to synthesize (Ba,Pb)TiO3 powder are the followings ; synthesis temperature (5$^{\circ}C$)