• Journal of Power Electronics
• /
• 제16권4호
• /
• pp.1324-1335
• /
• 2016

This article explores the speed regulation problem of permanent magnet synchronous motor (PMSM) systems subjected to unknown time-varying disturbances. A continuous sliding mode control (CSMC) technique is introduced for the speed loop to enhance the robustness of PMSM systems and eliminate the chattering phenomenon caused by high-frequency switch function in the conventional control law. However, the high control gain of the CSMC law in the presence of strong disturbances leads to large steady-state speed fluctuations for PMSM systems. In many application fields, PMSM systems are affected by time-varying disturbances instead of constant disturbances. For example, electric bicycles are usually affected by changing environmental disturbances, including wind speeds, road conditions, etc. These disturbances may be in the form of constant, ramp, and parabolic disturbances. Hence, a generalized proportional integral (GPI) observer is employed to estimate these types of disturbances. Then, the disturbance estimation method and the aforementioned CSMC method are combined to establish a composite sliding mode control method called the CSMC+GPI method for the speed loop of PMSM systems. Contrary to the conventional sliding mode control technique, the proposed method completely eliminates the chattering phenomenon caused by the switching function in the conventional control law. Moreover, a small control gain for the CSMC+GPI method is chosen by feed-forwarding estimated values to the speed controller. Hence, the steady-state speed fluctuations are small. The effectiveness of the proposed control scheme is verified by simulation and experimental result.

• Journal of Power Electronics
• /
• 제17권2호
• /
• pp.368-379
• /
• 2017

In this paper, a direct torque control algorithm with novel duty cycle-based modulation is proposed for permanent magnet synchronous motor drives fed by neutral-point clamped three-level inverters. Compared with the standard DTC, the proposed algorithm can suppress steady-state torque ripples as well as ensure neutral-point potential balance and smooth vector switching. A unified torque/flux evaluation table with multiple voltage vectors and precise control levels is established and used in this method. This table can be used to evaluate the effects of duty-cycle vectors on torque and flux directly, and the elements of the table are independent of the motor parameters. Consequently, a high number of appropriate voltage vectors and their corresponding duty cycles can be selected as candidate vectors to reduce torque ripples by looking up the table. Furthermore, small vectors are incorporated into the table to ensure the neutral-point potential balance with the numerous candidate vectors. The feasibility and effectiveness of the proposed algorithm are verified by both simulations and experiments.

• 한국경영과학회:학술대회논문집
• /
• 한국경영과학회 1996년도 추계학술대회발표논문집; 고려대학교, 서울; 26 Oct. 1996
• /
• pp.157-161
• /
• 1996

This paper presents a method for designing private networks considering response time under packet switching network environment Specifically, we propose the designing process of a private network, where the host is assumed to be synchronous and the terminals to be asynchronous, according to protocol and access lines. To calculate the response time for the networks, we use the mutual independent M/M/1 and M/W/s queueing models. Comparing the response time derived from the model with the actual one, it is found that the model yields almost same performance in a more economic way. From the experiment, it is suggested that the necessary number of lines as well as the response time for a specific network can be estimated properly by sensitivity analysis.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.425-430
• /
• 1998

This paper presents a high performance low switching PWM technique for the propulsion system of railway such as subway and high speed train. In order to achieve the continuous voltage control to six-step and a low harmonics with low switching frequency under 500Hz, the synchronous PWM technique is combined with a space vector overmodulation and implemented by using DSP. Improved performance and a validation of proposed method are showed by the digital simulation and the experimental results using a 1.65MVA IGBT VVVF inverter and inertia load equivalent to 160 tons railway vehicles.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2012년도 전력전자학술대회 논문집
• /
• pp.63-64
• /
• 2012

본 논문에서는, 태양광 AC 모듈 기반의 인터리브드 플라이백 인버터에서의 동기 정류기를 이용한 소프트 스위칭 제어 기법을 제안한다. 제안된 방식은, 동기정류기를 이용하여 다이오드의 전도손실을 줄이고, 1차측 주스위치의 ZVS(Zero Voltage Switching) 턴-온을 수행하여 스위칭 손실을 저감하였다. 본 논문에서는 제안된 시스템의 타당성을 이론적 분석과 시뮬레이션을 통해 검증한다.

• 전력전자학회논문지
• /
• 제25권4호
• /
• pp.279-285
• /
• 2020

An open-end winding (OEW) permanent magnet synchronous motor with dual inverters can synthesize large voltages for a motor with the same DC link voltage. This ability has the advantage of reducing the use of DC/DC boost converters or high voltage batteries. However, zero-sequence voltage (ZSV), which is caused by the difference in the combined voltage between the primary and secondary inverters, can generate a zero-sequence current (ZSC) that increases system losses. Among the methods for eliminating this phenomenon, combining voltage vector eliminated ZSV cannot be accomplished by the conventional Pulse Width Modulation(PWM) method. In this study, a PWM carrier generation method using functionalization to generate a switching pattern to suppress ZSC is proposed and applied to analyze the control influence of the center-zero vector in the switching sequence about the current ripple.

• Journal of Electrical Engineering and Technology
• /
• 제9권4호
• /
• pp.1332-1342
• /
• 2014

This paper proposes a novel test circuit for SiC transistors. On-state resistance under practical application conditions is an important characteristic for the device reliability and conduction efficiency of SiC transistors. In order to measure the on-state resistance in practical applications, high voltage is needed, and high current is also necessary to ignite performance for the devices. A soft-switching circuit based on synchronous buck topology is developed in this paper. To provide high-voltage and high-current stresses for the devices without additional spikes and oscillations, a resonant circuit has been introduced. Using the novel circuit technology, soft-switching can be successfully realized for all the switches. Furthermore, in order to achieve accurate measurement of on-state resistance under switching operations, an active clamp circuit is employed. Operation principle and design analysis of the circuit are discussed. The dynamic measurement method is illustrated in detail. Simulation and experiments were carried out to verify the feasibility of the circuit. A special test circuit has been developed and built. Experimental results confirm that the proposed circuit gives a good insight of the devices performance in real applications.

• Journal of Electrical Engineering and Technology
• /
• 제12권5호
• /
• pp.1891-1901
• /
• 2017

In this paper, optimal control of the fuel cell and design of a high-efficiency power converter is implemented to build a high-priced fuel cell system with minimum capacity. Conventional power converter devices use a non-isolated boost converter for high efficiency while the battery is charged, and reduce its conduction loss by using MOSFETs instead of diodes. However, the efficiency of the boost converter decreases, since overshoot occurs because there is a moment when the body diode of the MOSFET is conducted during the dead time and huge loss occurs when the dead time for the maximum-power-flowing state is used in the low-power-flowing state. The method proposed in this paper is to adjust the dead time of boost and rectifier switches by predicting the power flow to meet the maximum efficiency in every load condition. After analyzing parasite components, the stability and efficiency of the high-efficiency boost converter is improved by predictive compensation of the delay component of each part, and it is proven by simulation and experience. The variation in switching delay times of each switch of the full-bridge converter is compensated by falling time compensation, a control method of PWM, and it is also proven by simulation and experience.

• 조명전기설비학회논문지
• /
• 제24권4호
• /
• pp.81-94
• /
• 2010

본 논문에서는 고효율 공진형 비대칭 하프브리지 플라이백컨버터가 제안된다. 컨버터의 1차측 하프브리지 회로는 공진커패시턴스와 변압기 누설인덕턴스를 이용하여 비대칭 펄스폭변조(PWM; Pulse-Width Modulation) 방식에 의한 소프트스위칭 형태로 동작한다. 그리고 컨버터 2차측의 플라이백 회로는 간단한 구동회로에 의해 새로운 전압구동방식으로 동작하는 동기정류기를 이용한다. 제안된 컨버터는 이렇게 하여 컨버터의 전체효율을 향상시킨다. 또한 본 논문에서는 제안된 컨버터의 동작원리를 모드별로 설명하고 컨버터 설계 시의 고려사항과 프로토타입 컨버터의 설계 예를 각각 제시한다. 그리고 본 논문에서 제안하는 전압구동방식으로 동작하는 동기정류기의 간단한 구동기법에 관하여 간략하게 설명한다. 설계된 프로토타입 컨버터는 광범위 입력전압(교류 $V_{in,rms}$=75~265[V])이 가능하며 5[V]의 직류 출력전압과 100[W]의 출력전력을 가진다. 제안된 컨버터의 우수한 성능을 입증하기 위하여 설계된 파라미터로써 프로토타입 컨버터를 제작하여 실험하였으며, 이를 통하여 제안된 컨버터의 우수한 성능을 보인다.

• 전력전자학회논문지
• /
• 제24권6호
• /
• pp.445-451
• /
• 2019

An input power estimation method of a three-phase inverter for the high-efficiency operation of AC motors is proposed. Measuring devices, such as DC link voltage and input current sensors, are required to obtain the input power of the inverter. In the proposed method, the input power of the inverter can be estimated without the input current sensor by using the phase current information of the AC motor and the switching pattern of the inverter. The proposed method is more robust to parameter error than conventional method. The validity of the input power estimation method is verified through experiments conducted on a 1 kW permanent-magnet synchronous motor drive system.