• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.4
• /
• pp.321-328
• /
• 2008

In this paper, variable gain amplifier(VGA) with a gain slope controller has been proposed and verified by circuit simulations and measurements. The proposed VGA has a gain control, gain slope switch and variable gain range. The input source coupled pair with diode connected load is used for VGA gain stage. The gain slope controller with switch can control VGA gain slope. The proposed VGA is fabricated in $0.18{\mu}m$ CMOS process for multi -standard wireless receiver. The proposed two stage VGA consumes min. 2.0 mW to max. 2.6 mW in gain control range and gives input IP3 of -3.77 dBm and NF of 28.7 dB at 1.8 V power supply under -25 dBm, 1 MHz input. The proposed VGA has 37 dB(-16 dB $\sim$ 21 dB) variable gain range, and 8 dB gain range control per 0.3 V control voltage, and can provide variable gain, positive and negative gain slope control, and gain range control. This VGA characteristics provide design flexibility in multi-standard wireless receiver.

• The KIPS Transactions:PartC
• /
• v.14C no.6
• /
• pp.525-536
• /
• 2007

Network Control Platform(NCP) and Qualify of Service Switch(QSS) are being developed to realize centralized control and management technology, which is essential for guaranteeing traffic engineering and service quality in a next generation network. This paper adopts a parallel mechanism, and a thread and object pool to achieve high-speed connection management in the existing SNMP interface between NCP and QSS. We built up a connection management test-bed in laboratory environment to validate the functionality of high-speed connection management. We also measured and analyzed a performance of connection setup delay and a completion ratio using the test-bed. We ascertain that the parallel mechanism and the object pool are the most important performance parameters to achieve high-speed connection management in the SNMP interface between NCP and QSS.

• JOURNAL OF ELECTRICAL WORLD
• /
• no.10 s.106
• /
• pp.22-27
• /
• 1985

• KSCI Review
• /
• v.2 no.1
• /
• pp.35-44
• /
• 1995

• Journal of KIISE:Information Networking
• /
• v.34 no.3
• /
• pp.203-217
• /
• 2007

In this paper, a performance evaluation model of Networks with the multiple-buffered crossbar switches is proposed and examined. Buffered switch technique is well known to solve the data collision problem of the switch networks. The characteristic of a network with crossbar switches is determined by both the connection pattern of the switches and the limitation of data flow in a each switch. In this thesis, the evaluation models of three different networks : Multistage interconnection network, Fat-tree network, and other ordinary communication network are developed. The proposed evaluation model is developed by investigating the transfer patterns of data packets in a switch with output-buffers. Two important parameters of the network performance, throughput and delay, are evaluated. The proposed model takes simple and primitive switch networks, i.e., no flow control and drop packet, to demonstrate analysis procedures clearly. It, however, can not only be applied to any other complicate modern switch networks that have intelligent flow control but also estimate the performance of any size networks with multiple-buffered switches. To validate the proposed analysis model, the simulation is carried out on the various sizes of networks that uses the multiple buffered crossbar switches. It is shown that both the analysis and the simulation results match closely. It is also observed that the increasing rate of Normalized Throughput is reduced and the Network Delay is getting bigger as the buffer size increased.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.327-332
• /
• 1999

In this paper, six harmonic injection PWM method for reducing total harmonic distortion in single switch three phase discontinuous conduction mode boost converter is presented. In the proposed method, periodic six harmonic voltage is injected in the control circuit to vary the duty ratio of the converter switch within a line cycle so that the fifth order harmonic of the input current is reduced. Experimental results are verified by converter operating at 400V/6kW with three phase 140V~220V input.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 1999.11a
• /
• pp.23-28
• /
• 1999

The manufactured pulsed power system with 500kA current is described in this paper. The capacitor bank, control cabinent, dec charging unit, closing switch and dumping box, cable system etc. employed with the system components are described. Especially the development of the inverse pinch switch controlled by gas puffing enabled the generation of the very high voltage and current.

• Proceedings of the KIPE Conference
• /
• 2010.07a
• /
• pp.489-490
• /
• 2010

A novel soft-switching two-switch flyback converter is proposed in this paper. This converter is composed of two active power switches, a flyback transformer, and two passive regenerative clamping circuits.The proposed converter has the advantages of a low cost circuit configuration, a simple control scheme, a high efficiency, and a wide operating range. The circuit topology and experimental results of the new flyback converter are presented.

• Proceedings of the Korean Information Science Society Conference
• /
• 1999.10c
• /
• pp.396-398
• /
• 1999

단일 망으로 다양한 서비스를 제공하기 위하여 하나의 스위치에서 다수의 제어소프트웨어를 지원해야 한다. 이를 위하여 스위치의 제어 인터페이스를 표준화하려는 시도가 활발하다. 본 논문에서는 다수의 스위치를 단일 제어기로 제어하는 ATM 연결 제어 방법을 제안한다. 본 논문에서 제안하는 방법으로 제어망과 트랜스포트 망을 분리함으로써 유연한 망의 구성이 가능해지고, 병렬 스위치 제어를 통하여 시그널링의 효율을 꾀할 수 있다. 이를 위하여 단일 스위치를 통한 복합 연결 (compound connection)에 대하여 단일 제어 인터페이스를 통한 제어가 가능한 원소 연결(atomic connection)로의 변환 모델 등을 제시한다.

• Proceedings of the KIEE Conference
• /
• 1999.07e
• /
• pp.2179-2181
• /
• 1999

This paper describes the composition technology of pulsed power system with high current. The capacitor bank, control cabinet, dc charging unit, closing switch and cable system etc. employed with the system components are described. Especially the development of the inverse pinch switch enabled the generation of the very high current.