• Journal of Power Electronics
• /
• v.7 no.2
• /
• pp.109-117
• /
• 2007

In this paper, a novel proposal for a utility-interactive three-phase soft commutation sinewave PWM power conditioner with an auxiliary active resonant DC-link snubber is developed for fuel cell and solar power generation systems. The prototype of this power conditioner consists of a PWM boost chopper cascaded three-phase power conditioner, a single two-switch auxiliary resonant DC-link snubber with two electrolytic capacitors incorporated into one leg of a three-phase V-connection inverter and a three-phase AC power source. The proposed cost-effective utility-interactive power conditioner implements a unique design and control system with a high-frequency soft switching sinewave PWM scheme for all system switches. The operating performance of the 10 kW experimental setup including waveform quality, EMI/RFI noises and actual efficiency characteristics of the proposed power conditioner are demonstrated on the basis of the measured data.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.5
• /
• pp.3114-3120
• /
• 2014

Wireless emergency call switch used in industry, the most important thing is the sustainable power supply. This paper describes the development and performance test results of a compact electromagnetic energy harvesting mechanism for batteryless wireless switch. This paper summarizes proposed structure design and magnetic field analysis results of the mechanism to generate an induced electromotive force using 2mm stroke of a single push action. This analysis results show the power output of the proposed mechanism up to VDC $4.5V{\pm}25%$ and it can hold up to 65ms of the power generation with greater than 2.5V.

• Journal of Power Electronics
• /
• v.19 no.1
• /
• pp.11-23
• /
• 2019

In this study, a novel zero voltage zero current transition (ZVZCT) bidirectional DC-DC converter is proposed by employing coupled inductors. This converter can turn the main switch on at ZVZCT and it can turn it off with zero voltage switching (ZVS) for both the boost and buck modes. These characteristics are obtained by using a simple auxiliary sub-circuit regardless of the power flow direction. In the boost mode, the auxiliary switch achieves zero current switching (ZCS) turn-on and ZVS turn off. Due to the coupling inductors, this converter can make further efficiency improvements because the resonant energy in the capacitor or inductor can be transferred to the load. The main diode operates with ZVT turn-on and ZCS turn-off in the boost mode. For the buck mode, there is a releasing circuit to conduct the currents generated by the magnetic flux leakage to the output. The auxiliary switch turns on with ZCS and it turns off with ZVT. The main diode also turns on with ZVT and turns off with ZCS. The design method and operation principles of the converter are discussed. A 500 W experimental prototype has been built and verified by experimental results.

• Progress in Superconductivity and Cryogenics
• /
• v.9 no.1
• /
• pp.47-52
• /
• 2007

This paper presents characteristics analysis of persistent current switch(PCS) system on a small scale by using YBCO coated conductor(CC). A high temperature superconductor(HTS) PCS system mainly consists of a PCS, a HTS magnet load and a magnet power supply(MPS). To design the optimal heater triggering switch. the three-dimensional heat conduction model was analyzed by finite element method(FEM). The electrical equivalent model considering the n-value of CC was applied to analyze current decay during persistent current mode. In the experiment and simulation, the heater was applied with a current of 0.43A and the current was ramped up to 10A and 20A with 0.2A/s. Finally, experimental results of the HTS PCS system have been compared with the theoretical results. It has been concluded that flux creep can not influence the results because the operating current was 40% of critical current and optimal sequential operation of the PCS system is indispensable to enhance its performance.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.4
• /
• pp.96-105
• /
• 2013

This paper presents a standardization method for designing wire harness systems, based on the control types and functional blocks, for use in commercial vehicles. With a rapid increase in the installation of systems with added new features, it is very important to develop a reliable wire harness design in a short time by standardizing wire harness designs and reusing the standard design. Because the function of a system, particularly, for commercial vehicles, varies significantly on the basis of the requirements, regulations, and options, it is not effective to establish one standard design for one system. In addition, a system with the same function may differ in terms of the input conditions and output loads on the basis of the installed vehicle types, and it is not practical to standardize a harness design targeting an entire system. In this study, the wire harness designs of a system were classified into six categories based on the control types of the system: switch driven, control of a switch, control of an electronic control unit, unit driven, control of a unit, and connector operation. Then, a wire harness design of each system was divided into three blocks according to their functions: the control, drive, and monitoring blocks. The standard wire harness designs were made for each functional block of each control type. The advantage of this proposed method is that an effective and practical design can be obtained, which covers the diversities in the same system for different grades of commercial vehicles with a reduction in the number of wire harness supplements.

• The Transactions of the Korea Information Processing Society
• /
• v.3 no.7
• /
• pp.1868-1879
• /
• 1996

There are limitations to process high bandwidth traffic in B-ISDN with mesh- topology single bus architecture of current mobile communication system. And, it is impossible to import ATM switch using fixed length packet rather than variable length packet. Some implementations are able to process variable length packet, but there are some problems such as pre-processing for synchronization and bit delay. In this paper, we design a concentrator that can manipulate variable length packet without additional pre-process. There is on bit delay for packet starting signal in input interface, So it is more efficient to process packets, such that the concentrator can reduce he processing time as $\ulcornerlog2N\lrcorne＋1$ bit-time rather than N bit-time delay in ordinary concentrator. It is expected that the mobile communication system with partial mesh topology bus adopting the knockout switch architecture can process high bandwidth traffic in B-ISDN.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.7
• /
• pp.711-719
• /
• 2008

Although non-real time simulation and pilot based evaluations are available for the development of flight control computer prior to real flight tests, there are still many risky factors. The control law designed for prototype aircraft often leads to degraded performance from the initial design objectives, therefore, the proper evaluation methods should be applied such that flight control law designed can be verified in real flight environment. The one proposed in this paper is IFS(In-Flight Simulator). Currently, this system has been implemented into the F-18 HARV(High Angle of Attack Research Vehicle), SU-27 and F-16 VISTA(Variable stability. In flight Simulation Test Aircraft) programs. This paper addresses the concept of switching mechanism for FLCC(Flight Control Computer)-SWMC(Switching Mechanism Computer) using 1553B communication based on flight control law of advanced supersonic trainer. And, the fader logic of TFS(Transient Free Switch) and stand-by mode of reset '0' type are designed to reduce abrupt transient and minimize the integrator effect in pitch axis control law. It hans been turned out from the pilot evaluation in real time that the aircraft is controllable during the inter-conversion process through the flight control computer, and level 1 handling qualities are guaranteed. In addition, flight safety is maintained with an acceptable transient response during aggressive maneuver performed in severe flight conditions.

• Journal of Korean Society of Water and Wastewater
• /
• v.32 no.4
• /
• pp.309-315
• /
• 2018

Currently, the commercialization of the $5^{th}$ Generation (5G) service is becoming more prevalent in domestic communication network technology. This has reduced communication delay time and enabled large-capacity data transmission and video streaming services in real-time. In order to keep pace with these developments, K-water has introduced a smart process control system in water purification plants to monitor the status of the water purification process. However, since wireless networks are based on the public Long Term Evolution (LTE) network, communication delay time remains high, and high-resolution video services are limited. This is because communication networks still have a closed structure due to expense and security issues. Therefore, with 5G in its current form, it is very difficult to accommodate future services without improving the infrastructure of its communication networks. In recognition of these problems, this study implemented the authentication and management function of wireless networks on a wired network management system in the K-water Bansong water purification plant. The results confirmed that wired Local Area Network (LAN) services give a higher security performance than an expensive commercial wireless LAN system. This was achieved by using an Internet Protocol (IP) address management system of wired networks and the packet filtering function of the Layer2 (L2) switch. This study also confirmed that it is possible to create a wireless LAN service that is 3.7 times faster than the existing LTE communication network.

• Journal of electromagnetic engineering and science
• /
• v.14 no.3
• /
• pp.284-292
• /
• 2014

This paper presents a characteristic evaluation of commercial gallium nitride (GaN) transistors having two different gate-lengths of $0.4-{\mu}m$ and $0.25-{\mu}m$ in the design of a class-S power amplifier (PA). Class-S PA is operated by a random pulse-width input signal from band-pass delta-sigma modulation and has to deal with harmonics that consider quantization noise. Although a transistor having a short gate-length has an advantage of efficient operation at higher frequency for harmonics of the pulse signal, several problems can arise, such as the cost and export license of a $0.25-{\mu}m$ transistor. The possibility of using a $0.4-{\mu}m$ transistor on a class-S PA at 955 MHz is evaluated by comparing the frequency characteristics of GaN transistors having two different gate-lengths and extracting the intrinsic parameters as a shape of the simplified switch-based model. In addition, the effectiveness of the switch model is evaluated by currentmode class-D (CMCD) simulation. Finally, device characteristics are compared in terms of current-mode class-S PA. The analyses of the CMCD PA reveal that although the efficiency of $0.4-{\mu}m$ transistor decreases more as the operating frequency increases from 955 MHz to 3,500 MHz due to the efficiency limitation at the higher frequency region, it shows similar power and efficiency of 41.6 dBm and 49%, respectively, at 955 MHz when compared to the $0.25-{\mu}m$ transistor.

• Journal of Internet of Things and Convergence
• /
• v.6 no.1
• /
• pp.97-102
• /
• 2020

Multi-Channel Switch ICs for IoT have integrated several solid state structure low ON-resistance bi-directional relay MOS switches with level shifter to drive high voltage and they should be independently controlled by external serialized logic control. These devices are designed for using in applications requiring high-voltage switching control by low-voltage control signals, such as medical ultra-sound imaging, ink-jet printer control, bare board open/short and leakage test system using Kelvin 4-terminal measurement method. This paper describes implementation of analog switch control block and its verification using Field programmable Gate Array (FPGA) test pattern generation. Each block has been implemented using Verilog hardware description language then simulated by Modelsim and prototyped in a FPGA board. Compare to conventional IC, The proposed architecture can be applied to fields where multiple entities need to be controlled simultaneously in the IoT environment and the proposed pattern generation method can be applied to test similar types of ICs.